• Korean Journal of Metals and Materials
• /
• v.48 no.7
• /
• pp.630-638
• /
• 2010

The present investigation has been performed on the mixing behavior and microstructural development during fabrication of Fe micro-nano powder feedstock for a micro-powder injection molding process. The mixing experiment using a screw type blender system was conducted to measure the variations of torque and temperature during mixing of Fe powder-binder feedstock with progressive powder loading for various nano-powder compositions up to 25%. It was found that the torque and the temperature required in the mixing of feedstock increased proportionally with increasing cumulative powder loading. Such an increment was larger in the feedstock containing higher content of nano-powder at the same powder loading condition. However, the maximum value was obtained at the nano-powder composition of not 25% but 10%. It was owing to the 'roller bearing effect' of agglomerate type nano-powder acting as lubricant during mixing, consequently leading to the rearrangement of micro-nano powder in the feedstock. It is concluded that the improvement of packing density by rearrangement of nano-powders into interstices of micro-powders is responsible for the maximum powder loading of about 71 vol.% in the nano-powder composition of 25%.

• Journal of Powder Materials
• /
• v.15 no.4
• /
• pp.271-278
• /
• 2008

Sintering behavior of iron nanopowder agglomerate compact prepared by slurry compaction method was investigated. The Fe nanopowder agglomerates were prepared by hydrogen reduction of spray dried agglomerates of ball-milled $Fe_2O_3$ nanopowder at various reduction temperatures of $450^{\circ}C$, $500^{\circ}C$ and $550^{\circ}C$, respectively. It was found that the Fe nanopowder agglomerates produced at higher reduction temperature have a higher green density compact which consists of more densified nanopowder agglomerates with coarsed nanopowders. The sintering behavior of the Fe nanopowder agglomerates strongly depended on the powder packing density in the compact and microstructure of the agglomerated nanopowder. It was discussed in terms of two sintering factors affecting the entire densification process of the compact.

• Journal of the Korean Ceramic Society
• /
• v.34 no.11
• /
• pp.1173-1181
• /
• 1997

Effects of particle size distribution of alumina ceramics on behaviors of tape casting were investigated with emphases on the rheological characteristic of slurry, green density, green sheet strength, and sintering density. For the control of particle size distribution of alumina, the commercial grade low soda alumina, which had different mean particle size of 3.58 ${\mu}{\textrm}{m}$ and 0.42 ${\mu}{\textrm}{m}$, were chosen and blended together. As results, the mixing of 80 wt% fine powder and 20 wt% coarse powder(designated to FC20) led to the increase of packing density and strength of green sheet, and made it easy to handle during processing without lowering of sintering density. Besides, the pseudoplastic behavior of slurry decreased with increase of the fraction of coarse alumina powder.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.916-917
• /
• 2006

Solid Oxide Fuel Cell technology uses powder processes to produce electrodes with residual porosity by partially sintering a mixture of electronically and ionically conducting particles. We model porous fuel cell electrodes with 3D packings of monosized spherical particles. These packings are created by numerical sintering. Each particle-particle contact is characteristic for an ionic, electronic or electrochemical resistance. The numerical packing is then discretized into a resistor network which is solved by using Kirchhoff's current law to evaluate the electrode's electrochemical performance. We investigate in particular percolation effects in functionally graded electrodes as compared to other types of electrodes.

• Journal of the Korean Ceramic Society
• /
• v.49 no.4
• /
• pp.363-368
• /
• 2012

Nitriding and post-sintering behavior of powder mixture compacts were investigated. As mixture compacts are different from simple Si compacts, the fabrication of a sintered body with a mixture composition has engineering implications. In this research, in specimens without a pore former, the extent of nitridation increased with $Si_3N_4$ content, while the highest extent of nitridation was measured in $Si_3N_4$-free composition when a pore former was added. Large pores made from the thermal decomposition of the pore former collapsed, and they were filled with a reaction product, reaction-bonded silicon nitride (RBSN) in the $Si_3N_4$-free specimen. On the other hand, pores from the decomposed pore former were retained in the $Si_3N_4$-added specimen. Introduction of small $Si_3N_4$ particles ($d_{50}=0.3{\mu}m$) into a powder compact consisting of large silicon particles ($d_{50}=7{\mu}m$) promoted close packing in the green body compact, and resulted in a stable strut structure after decomposition of the pore former. The local packing density of the strut structure depends on silicon to $Si_3N_4$ size ratio and affected both nitriding reaction kinetics and microstructure in the post-sintered body.

• Culinary science and hospitality research
• /
• v.7 no.3
• /
• pp.145-161
• /
• 2001

In odor to develop fillet-type seasoner and mixed powder-type seasoner using smoked mackerel as primary material, processing conditions of the mackerel meat and flavoring extract from various materials were examined. The approximate composition of mackerel meat and mixed powde-type seasoner using mackerel as primary material were 10.9 and 11.7%, for moisture 79.1 and 57.2% for crude protein, 5.3 and 2.9% for crude lipid, and 4.3 and 24.6% for crude ash, respectively. It was suitable to simmer raw mackerel in 3% chitooligosaccaride solution at 8$0^{\circ}C$ for 10 min., for the enhancement of reaction their meat and chitooligosaccharide. Considering effect of type of woodsmoke on organoletic properties of mackerel after smoking, oak and mixture(oak wood ＋ citrus wood = 1 : 1) were superior to another woodsmoke, the smoking conditions favoring the most overall preference were 8$0^{\circ}C$, 25min. for smoking time, 20$0^{\circ}C$, 20min. for baking, and 10$0^{\circ}C$. 4hrs. for drying. The optimal material mixing ratio for mixed powder-type seasoner was powder of smoked mackerel 60%, dried anchovy 15%, dried sea tangle 10%. The most appropriate extraction condition of mixed powder seasoner with packing tea bag(10g/bag) was 98$^{\circ}C$ for 5min. in the boiling water.

• Journal of Powder Materials
• /
• v.24 no.2
• /
• pp.147-152
• /
• 2017

Spherical-type zirconia granules are successfully fabricated by a spray-drying process using a water solvent slurry, and the change in the green density of the granule powder compacts is examined according to the organic polymers used. Two organic binders, polyvinyl alcohol (PVA) and 2-hydroxyethyl methacrylate (HEMA), which are dissolved in a water solvent and have different degrees of polymerization, are applied to the slurry with a plasticizer (polyethylene glycol). The granules employing a binder with a higher degree of polymerization (PVA) are not broken under a uniaxial press; consequently, they exhibit a poor green density of $2.4g/cm^3$. In contrast, the granule powder compacts employing a binder with a lower degree of polymerization (HEMA) show a higher density of $2.6g/cm^3$ with an increase in plasticizer content. The packing behavior of the granule powders for each organic polymer system is studied by examining the microstructure of the fracture surface at different applied pressures.

• Journal of Powder Materials
• /
• v.31 no.3
• /
• pp.213-219
• /
• 2024

Additive Manufacturing (AM) is a process that fabricates products by manufacturing materials according to a three-dimensional model. It has recently gained attention due to its environmental advantages, including reduced energy consumption and high material utilization rates. However, controlling defects such as melting issues and residual stress, which can occur during metal additive manufacturing, poses a challenge. The trial-and-error verification of these defects is both time-consuming and costly. Consequently, efforts have been made to develop phenomenological models that understand the influence of process variables on defects, and mechanical/ electrical/thermal properties of geometrically complex products. This paper introduces modeling techniques that can simulate the powder additive manufacturing process. The focus is on representative metal additive manufacturing processes such as Powder Bed Fusion (PBF), Direct Energy Deposition (DED), and Binder Jetting (BJ) method. To calculate thermal-stress history and the resulting deformations, modeling techniques based on Finite Element Method (FEM) are generally utilized. For simulating the movements and packing behavior of powders during powder classification, modeling techniques based on Discrete Element Method (DEM) are employed. Additionally, to simulate sintering and microstructural changes, techniques such as Monte Carlo (MC), Molecular Dynamics (MD), and Phase Field Modeling (PFM) are predominantly used.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.1
• /
• pp.21-26
• /
• 2005

In order to simulate the powder compaction process and to assess the effects of packing randomness and particle arrangement 2-dimensional model of rod array compaction using quasi-random multiparticle array is introduced. The elastic modulus of porous ceramics is computed by the homogenization method. With 3 Al₂O₃ and 3 Al particles the compaction processes associated with the porosities are simulated by the explicit finite element method, based on the elastic modulus found by the homogenization method. The simulation results are compared with both previous analytical ones and experimental measurements. Finally, in order to find the relationship between the friction coefficient of powder particles and the relative density, the sensitivity analysis is performed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.1
• /
• pp.57-63
• /
• 2017

High-purity ${\beta}-SiC$ powders for SiC single-crystal growth were synthesized by direct carbonization. The use of high-purity raw materials to improve the quality of a SiC single crystal is important. To grow SiC single crystals by the PVT method, both the particle size and the packing density of the SiC powder are crucial factors that determine the sublimation rate. In this study, we tried to produce high-purity ${\beta}-SiC$ powder with large particle sizes and containing low silicon by introducing a milling step during the direct carbonization process. Controlled heating improved the purity of the ${\beta}-SiC$ powders to more than 99 % and increased the particle size to as much as ${\sim}100{\mu}m$. The ${\beta}-SiC$ powders were characterized by SEM, XRD, PSA, and chemical analysis to assess their purity. Then, we conducted single-crystal growth experiments, and the grown 4H-SiC crystals showed high structural perfection with a FWHM of about 25-48 arcsec.