• Archives of Pharmacal Research
• /
• v.26 no.7
• /
• pp.569-574
• /
• 2003

Controlled-release amitriptyline pellets (ATP) were formulated and its oral bioavailability was assessed in human volunteers after oral administration under fasting conditions. Core pellets were prepared using a CF granulator by two different methods (powder layering and solvent spraying) and coated with Eudragit RS or RL 100. Physical characteristics and dissolution rates of core pellets and coated pellets were evaluated to optimize the formulation. Powder layering method resulted in a better surface morphology than solvent spraying method. However, physical properties of the products were poorer when prepared by powder layering method with respect to hardness, friability and density. The dissolution profile of amitriptyline coated with Eudragit RS 100 was comparable to that of commercially available amitriptyline enteric-coated pellets ($Saroten^{\circledR}$ retard). After the oral administration of both products at the dose of 50 mg, the mean maximum concentrations ($C_{max}$) were 36.4 and 29.7 ng/mL, and the mean areas under the concentration-time curve ($AUC_{0-96}$) were 1180.2 and 1010.7 ng.h/mL for ATP and Saroten retard, respectively. The time to reach the maximum concentrations ($T_{max}$) was 6 h for both formulations. Statistical evaluation suggested that ATP was bioequivalent to Saroten retard.

• Journal of the Korean Ceramic Society
• /
• v.51 no.5
• /
• pp.477-480
• /
• 2014

An $Al_2O_3$-CuO-ZnO (ACZ) precursor powder was synthesized by a facial sol-gel process using a nonionic surfactant span 80 as the chelating agent to improve the surface area and morphology. When creating a hydrogen membrane, several kinds of properties are required, such as easy dissociation of hydrogen molecules, fast hydrogen diffusion, high hydrogen solubility, and resistance to hydrogen embrittlement. ACZ-Ni composite membranes (cermet) were prepared with this precursor and pure Ni powder via the hot press sintering (HPS) method. The ACZ powder was characterized by XRD, BET, and FE-SEM. Hydrogen permeation experiments were performed by Sievert's type of hydrogen permeation membrane equipment. The hydrogen permeability of ACZ/Ni 10 wt% and ACZ/Ni 20 wt% was obtained as 7.2 and $10molm^{-2}s^{-1}$ at RT, respectively. These values of the corresponding membranes were slightly increased with increasing pressures.

• Korean Journal of Materials Research
• /
• v.22 no.4
• /
• pp.174-179
• /
• 2012

In this study, we demonstrated a simple and eco-friendly method, including mechanical polishing and attrition milling processes, to recycle sputtered indium tin oxide targets to indium tin oxide nanopowders and targets for sputtered transparent conductive films. The utilized indium tin oxide target was first pulverized to a powder of sub- to a few- micrometer size by polishing using a diamond particle coated polishing wheel. The calcination of the crushed indium tin oxide powder was carried out at $1000^{\circ}C$ for 1 h, based on the thermal behavior of the indium tin oxide powder; then, the powders were downsized to nanometer size by attrition milling. The average particle size of the indium tin oxide nanopowder was decreased by increasing attrition milling time and was approximately 30 nm after attrition milling for 15 h. The morphology, chemical composition, and microstructure of the recycled indium tin oxide nanopowder were investigated by FE-SEM, EDX, and TEM. A fully dense indium tin oxide sintered specimen with 97.4% of relative density was fabricated using the recycled indium tin oxide nanopowders under atmospheric pressure at $1500^{\circ}C$ for 4 h. The microstructure, phase, and purity of the indium tin oxide target were examined by FE-SEM, XRD, and ICP-MS.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.138.2-138.2
• /
• 2010

Scandium-doped zirconium, ScSZ-based electrolyte, provides higher oxygen conductivity than YSZ and nano-based electrolyte materials are ideal for fabricating thin film electrolyte membrane of SOFC unit cell. Moreover, it may be applied to anode and cathode as well as electrolyte as ionic conductor. In this report, nano-based ScSZ-based electrolyte powder was prepared by co-precipitation synthesis. The particle size, surface area and morphology of the powder were observed by SEM and BET. Thin film electrolyte of under $10{\mu}m$ was fabricated by tape casting and co-firing using the synthesized ScSZ-based powders, and ionic conductivity and gas permeability of electrolyte film were evaluated. Finally, the SOFC unit cell was fabricated using the anode-supported electrolyte prepared by a tape casting method and co-sintering. Electrochemical evaluations of the SOFC unit cell, including measurements such as power density and impedance, were performed and analyzed.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.3
• /
• pp.177-182
• /
• 2017

The properties of electroless Ni-B thin film on diamond powder with different parameters (temperature, pH, surfactant etc.) were studied. The surface morphology, structure and composition distribution of the Ni-B film were observed by field effect scanning electron microscope (FE-SEM), energy-dispersive spectrometer (EDS), X-ray diffraction (XRD) and Auger electron spectroscopy (AES). The growth rate of Ni-B film was increased with increase of bath temperature. The B content in Ni-B film was reduced with increase of bath pH. As a result the structure of Ni-B film was changed from amorphous to crystalline structure. The PVP in solution plays multi-functional roles as a dispersant and a stabilizer. The Ni-B film deposited with adding 0.1 mM-PVP was strongly introduced an amorphous structure with higher B content (25 at.%). Also the crystallite size of Ni-B film was reduced from 12.7 nm to 5.4 nm.

• Journal of the Korean Ceramic Society
• /
• v.30 no.4
• /
• pp.279-288
• /
• 1993

A study on calcination and reduction of AUC(ammonium uranyl carbonate, (NH4)4UO2(CO3)3) has been carried out by using TG-DTA in N2, air and H2 atmospheres, respectively. Phases of various intermediate obtained during thermal analysis of AUC in different atmospheres were confirmed by XRD. Powder characteristics of each intermediate were investigated by measuring particle size and specific surface area, and also observed by SEM. As a results, regardless of applied atmosphere AUC was calcined into amorphous UO3, which was converted to $\alpha$-U3O8 Via $\alpha$-UO3 in both H2 and N2 atmosphere, but directly into $\alpha$-UO3 in air atmosphere. Further reduction of U3O8 was only detectable in hydrogen atmosphere. During calcination and reduction, average particle size was reduced to less than 30% of original value without morphology change. Specific surface area was dramatically increased with release of NH3, CO2 and H2O from AUC powder and reached maximum value around 25$0^{\circ}C$, and then gradually decreased with the increase of temperature due to sintering effect of uranium oxides such as UO3 and U3O8. It was also found that the change of average crystallite size and pore size were closely related to the changes of specific surface area of uranium oxides.

• Journal of the Korean Ceramic Society
• /
• v.42 no.7 s.278
• /
• pp.497-502
• /
• 2005

This study investigated the effects of the substrate and powder content on the fabrication of SiO$_{2}$ photonic crystals by evaporation method. Photonic crystals were self-assembled on quartz, Corning 1737 glass, slide glass, and ITa glass to verify the effects of the wetting angle and surface morphology. The powder contents of the solution were varied from 0.2 to 2.0 wt$\%$. The number of photonic crystal layers increased according to the decrease of wetting angle and surface roughness. The resultant photonic crystals showed the best optical characteristics when the number of photonic crystal layers was within 40 and 50. In addition, the intensity peak of Fabry¡?Perot fringes increased when the wetting angle was large and the particle size was small. Photonic crystals coated on ITO glass showed the highest reflectance peak of 63$\%$ relative intensity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.213-213
• /
• 2010

In this thesis, we studied to increased to solar conversion efficiency of DSSC (dye-sensitized solar cell) using nanocrystalline $TiO_2$ semiconductor. We are preparation of $TiO_2$ photoelectrode, assembly the DSSC and put a focus in analyses electrochemical properties of DSSC and using Silica powder in $TiO_2$ photoelectrode for increase light scattering effect and improved conversion efficiency. It attempt to investigate the morphology of the photoelectrode and photovoltaic effects using field emission scanning electron microscopy (FE-SEM) and photovoltaic properties under illumination with AM 1.5 simulated sunlight. We got 146 % enhanced power conversion efficiency when the optimal content of quartz glass powder was 5 wt.% than that another content.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.592-595
• /
• 2009

Nanosize NiO powder was prepared by mixing acidic nickel nitrate with basic nickel carbonate. The particle size and morphology of NiO were mainly governed by the mole ratio of the nitrate to the carbonate. The effects were studied by DSC, XRD, FTIR, and SEM. Heat treatment conditions influence the particle size distribution of produced NiO powder extensively for the case of 3N7C (3 moles of the nitrate and 7 moles of the carbonate) and 4N6C, but only slightly for 1N9C and 2N8C. Uniform pseudospherical NiO particles were obtained in $50{\sim}70$ nm for 1N9C and $30{\sim}60$ nm for 2N8C by calcination at $750{^{\circ}C}$ for 2 h.

• Journal of Korea Foundry Society
• /
• v.10 no.5
• /
• pp.435-443
• /
• 1990

By using the centrifugal atomization, which is one of the rapid solidification processes, Al-5,10wt%Pb alloys which are monotectic alloys were melted at 150K over two liquid phase line in the phase diagram. The melted alloy was poured on the rotating disk, being made into atomized powders, and then the solidified microstructure and morphology of the powder were investigated. This study converted the produced powders into strips by strained powder rolling. According to sintering temperature, the microstructure and hardness were investigated. The solidified structure of the powders were almost cellular dendritic structure. Pb particles ($2.0-3.0{\mu}m$) were fairl distributed in the Al matrix. Powder shapes were irregular. Rolling property and the compacting was good, respectively, because of increasing mechanical interlocking and surface area in the small size powders. With increasing temperature, the boundarys of powders were in porous form due to the diffusion. Pb particles which were surrounding the pores were inverse-segregated at the surface of the powders. With increasing of sintering temperature, the hardness of the powders and the strips decreased. In particular rolling-strip, the hardness abruptly decreased due to the release of work-hardening.