• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.11a
• /
• pp.160-161
• /
• 2015

This research reviewed the characteristics of waste concrete sludge occurred from recycled aggregate producing process and the physical and mechanical properties of the mortar incorporated the pulverized the waste concrete sludge. From the results of the experiment, as the replacement ratio of waste concrete sludge powder was increased, the dosage of superplasticizer to satisfy the target flow of 200 ± 10 was increased, and the compressive and flexural strengths were decreased. On the other hand, when the sludge powder replacement ratio was 25 %, outstanding performance of general characteristics of mortar was obtained while it was lower than Plain mixture, thus, further detail study on various replacement ratios of waste concrete sludge powder is needed.

• Journal of Food Hygiene and Safety
• /
• v.11 no.3
• /
• pp.221-225
• /
• 1996

For the purpose of improving hygienic quality of health-foods, sterilization effects of ${\gamma}$-ray and ozone on microoganisms associated with food cultured in the media and contaminated in Angelica keiskei powder were investigated. Ozone was immersed in water and sprayed in air, on the concentration of 3 mg liter-1 at an air flow rate of 5 liter min-3. Test strains cultured in the media completely inhibited by ${\gamma}$-ray at irradiation doses of 0.25~2 kGy. In the case of ozone, test bacteria inactivated after treatment of 10~20 minutes, but test mold, Aspergillus flavus was not effective. Strains contaminated in Angelica keiskei powder completely inhibited by ${\gamma}$-ray at irradiation doses of 2.5~7.5 kGy. However, when the powder was sprayed with ozonized air for 10hours, Bacillus subtilis and Staphylococcus aureus among five strains were eliminated.

• Journal of environmental and Sanitary engineering
• /
• v.11 no.1
• /
• pp.63-70
• /
• 1996

The synthesis of high purity and ultra-fine $BaTiO_3$ by precipitation with gaseous $NH_3$ as precipitator was investigated to find an alternative process to solve various problems of recent wet methods. A synthesis process for $BaTiO_3$ powder using $NH_3$ gas as a precipitator in a bubble column reactor was experimentally successful in developing the production process of piezoelectric ceramic $BaTiO_3$ powder. And a 2.33m1/sec is approprite for the feed flow rate, $BaTiO_3$ powder produced under above the condition is spherical type, its particle size was about $0.2{\mu}m$.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.204-209
• /
• 1995

The implementation of rapid prototyping technologies has been developed for automotive engineering by utilizing concurrent engineering principes integrated with slective laser sintering. The Selective Laser Sintering, in which a part is generated in layers form powder using a computer-controlled laser scanning apparatus and power feed system. An over view of the basic principles of SLS Machine operation is given. Binding mechanisms are described for power which becomes thermally activated bye the scanning laser beam; viscous flow and melting of a low-melting-point phase in powder. The production of parts from metal is described, including post processing to improve structural integrity and induce a transformation.

• Proceedings of the Korean Printing Society Conference
• /
• 2007.11a
• /
• pp.59-64
• /
• 2007

We have manufactured low-curable silver pastes for gravure printing out of roll to roll printing process. When printing, the pastes be used different silver powder shape because of the printing characteristics. The pastes were prepared with silver powder by silver powder shape, polyester resin, solvent and homogenized on a standard three-roller mill. And the pastes exhibited a shear-thinning flow at viscosity profile. Moreover the adhesive strength and resistivity of silver film had good characteristics. With the manufactured paste in this study, RFID antenna circuit had flexible is manufactured and it had $10^{-4}{\sim}10^{-5}{\Omega}{\cdot}cm$.

• Journal of Powder Materials
• /
• v.15 no.4
• /
• pp.297-301
• /
• 2008

The Ni-based bulk metallic glass matrix composites were fabricated by spark plasma sintering of mixture of gas-atomized metallic glass powders and ductile brass powders. The successful consolidation of metallic glass matrix composite was achieved by strong bonding between metallic glass powders due to viscous flow deformation and lower stress of ductile brass powders in the supercooled liquid state during spark plasma sintering. The composite shows some macroscopic plasticity after yielding, which was obtained by introducing a ductile second brass phase in the Ni-based metallic glass matrix.

• Journal of Powder Materials
• /
• v.9 no.5
• /
• pp.322-328
• /
• 2002

Fe-Co nanocomposite powders with different composition were prepared by chemical vapor condensation (CVC) process and their characterizations were studied by means of X-ray diffraction, transmission electron microscopy, and vibrating sample magnetometer. The particles having the mean size of 5~25 nm consisted of metallic cores and oxide shells. The Co contents and particle size increased with increasing the carrier gas flow rate of Co precursor. The saturation magnetization and coercivity increased with increasing Co content. and the saturation magnetization maximized at the 40 wt.%Co. The Fe-Co nanocomposite powder oxidized at $400^{\circ}C$ showed the maximum coercivity of 1739 Oe.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.50 no.2
• /
• pp.27-34
• /
• 2008

Recently, owing to the development of industry and improvement of building techniques, concrete structures are becoming larger and higher. This study was performed to analyze hydration reation properties of concrete with binders and admixtures, such as OPC, low heat cement, belite rich cement, slag powder, lime powder and fly ash. To investigate effects of PC type superplasticizer on the hydration, experiments involving FT-IR, XRD, DSC, SEM were analyzed at the curing age 1day, 3days and 28days. The hydration reaction rate of OPC concrete slightly delayed at the curing age 1day, blast furnace slag powder and fly ash were more effective. BRC and LHC concretes can be used for concrete structures in winter season.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.278-279
• /
• 2014

This study was performed an evaluation of mechanical properties of reactive powder concrete using copper slag. So, various RPC containing copper slag were made by replacement ratio of copper slag and different the curing condition and their mechanical properties were investigated. From the experimental results, slump flow using copper slag tends to increase with replacement ratio. And also, 30% of copper slag with quartz sand was found to have a compressive strength superior to that of plain.

• Journal of Powder Materials
• /
• v.14 no.6
• /
• pp.405-409
• /
• 2007

The Cu-based bulk metallic glass (BMG) composites containing Zr-based metallic glass phase have been consolidated by spark plasma sintering using the mixture of Cu-based and Zr-based metallic glass powders in their overlapped supercooled liquid region. The Zr-based metallic glass phases are well distributed homogeneously in the Cu-based metallic glass matrix after consolidation process. The successful consolidation of BMG composites with dual amorphous phases was corresponding to the sound viscous flow of the two kinds of metallic glass powders in their overlapped supercooled liquid region.