• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.1005-1006
• /
• 2006

This paper proposes a method of position estimating through compensating the autonomous mobile robot's noise. Proposed method is that estimated position error by modified Kalman filter method using neural network. We use a neural network for measurement noise covariance and system noise covariance. In order to verify the effectiveness of the proposed method, we performed experiments for position estimation. The results show that convergence and position error is reduced than the Kalman filter method.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.8
• /
• pp.457-466
• /
• 2002

The speed and position control of SRM(Switched Reluctance Motor) needs the encoder or resolver to obtain the rotor position information. These position sensors can be affected by the EMI, dusty, and high temperature surroundings. Therefore the speed and position sensorless control has been studied widely In this paper, the binary observer of the SRM which has two feedback compensation loops to control the speed of SRM is proposed. One loop reduces the estimation error like the sliding mode observer, and the other removes the estimation error chattering occurred in the sliding mode observer. This observer is constructed on the basis of variable structure control theory and has the inertial term to exclude the chattering. This method has a good estimation performance in spite of nonlinear modeling of SRM. The advantages of the proposed method are verified experimentally.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.64.5-64
• /
• 2001

It is a very important problem that we grasp the accurate position at car navigation system. The GPS has used for knowing position because of accumulating few errors, but it have errors that are Tropospheric error, ionospheric error and Multipath error and so on. In this paper, We estimate moving position of a vehicle by Kalman filter using initial value after deducing the line equation using initial value and target value of map data. Then, we compensate GPS errors compare estimated poing with GPS errors. The experimental results have shown that are compared position data during real travel with compensated position data which are got after applying the algorithm ...

• Journal of Sensor Science and Technology
• /
• v.25 no.3
• /
• pp.202-207
• /
• 2016

Estimation of vertical position is critical in applications of sports science and fall detection and also controls of unmanned aerial vehicles and motor boats. Due to low accuracy of GPS(global positioning system) in the vertical direction, the integration of IMU(inertial measurement unit) with the GPS is not suitable for the vertical position estimation. This paper investigates an IMU-barometer integration for estimation of vertical position (as well as vertical velocity). In particular, a new two-step Kalman/complementary filter is proposed for accurate and efficient estimation using 6-axis IMU and barometer signals. The two-step filter is composed of (i) a Kalman filter that estimates vertical acceleration via tilt orientation of the sensor using the IMU signals and (ii) a complementary filter that estimates vertical position using the barometer signal and the vertical acceleration from the first step. The estimation performance was evaluated against a reference optical motion capture system. In the experimental results, the averaged estimation error of the proposed method was 19.7 cm while that of the raw barometer signal was 43.4 cm.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.8
• /
• pp.752-759
• /
• 2008

In this paper, we propose a high accurate geo-location system based on a single base station, where its location is obtained by Time-of-Arrival(ToA) and Direction-of-Arrival(DoA) of the radio signal. For estimating accurate ToA and DoA information, a MUltiple SIgnal Classification(MUSIC) is adopted. However, the estimation of ToA and DoA using MUSIC algorithm is a time-consuming process. The position tracking bias is occurred by the time delay caused by the estimation process. In order to mitigate the bias error, we propose the estimation method of the position tracking bias and compensate the location error produced by the time delay using the position tracking bias mitigation. For accurate self-localization of mobile robot, the Unscented Kalman Filter(UKF) with position tracking bias is applied. The simulation results show the efficiency and accuracy of the proposed geo-location system and the enhanced performance when the Unscented Kalman Filter is adopted for mobile robot application.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2150-2161
• /
• 2016

Mechanical and electrical parameter uncertainties cause dynamic and static estimation errors of the rotor speed and position, resulting in performance deterioration of sensorless control systems. This paper applies an extended nonlinear observer to interior permanent magnet synchronous motors (IPMSM) for the simultaneous estimation of the rotor speed and position. Two compensation methods are proposed to improve the observer performance against parameter uncertainties: an on-line rotational inertia adjustment approach that employs the gradient descent algorithm to suppress dynamic estimation errors, and an equivalent flux error compensation approach to eliminate static estimation errors caused by inaccurate electrical parameters. The effectiveness of the proposed control strategy is demonstrated by experimental tests.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.483-487
• /
• 1996

We consider the estimation of the position and orientation of 6 DOF motion bed (Stewart platform) from the measured cylinder length. The solution of forward kinematics is not solved yet as a useful realtime application tool because of the complity of the equation with multiple solutiple solutions. Hence we suggest an algorithm for the estimation of forward kinematics solution using Luenberger observer withnonlinear error correction term. The Luenberger observer withlinear model shows that the estimation error does not go to zero in steadystate due to the linearization error of the dynamic model. Hence the linear observer is modified using nonlinear measurement error equation and we prove thd practical stability of the estimation error dynamics of the proposed observer using lyapunov function.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.1
• /
• pp.119-126
• /
• 2000

In constructing the positioning system based on a conventional dead-reckoning for a wheeled vehicle with pneumatic tires, the position estimation error is inevitable as changes of the radius of the wheels depend on live load and variable enviroment. Therefore, this paper proposes the positioning system which can estimate the error source i.e. the vehicle parameter errors, such as the right and left wheel radius error, using gyroscope and ultrasonic sensor and correct the parameter to reduce the dead-reckoned position estimation error. The extended Kalman filter was used as a method for the multisensor data fusion. The simulation to verify the effectiveness of the proposed positioning system is performed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.491-497
• /
• 2004

This paper presents a new rotor position estimation method for brushless DC motors. It is clear that the estimation error of the rotor position provokes the phase shift angle misaligned between the phase current and the back-EMF waveforms, which causes torque ripple in brushless DC motor drives. Such an estimation error can be reduced with the help of the proposed neutral voltage-based estimation method that is structured in the form of a closed loop observer. A neutral voltage appearing during the normal mode of the inverter operation is found to be an observable and controllable measure, which can be dealt with for estimating an exact rotor position. This neutral voltage is obtained from the DC-link current, the switching logic, and the motor speed values. The proposed algorithm, which can be implemented easily by using a single DC-link current and the motor terminal voltage sensors, is verified by simulation and experiment results.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10b
• /
• pp.187-192
• /
• 1992

There are several potential error sources that can affect the estimation of the position of an object using combined vision and acceleration measurements. Two of the major sources, accelerometer dynamics and random noise in both sensor outputs, are considered. Using a second-order model, the errors introduced by the accelerometer dynamics are reduced by the smaller value of damping ratio and larger value of natural frequency. A Kalman filter approach was developed to minimize the influence of random errors on the position estimate. Experimental results for the end-point movement of a flexible beam confirmed the efficacy of the Kalman filter algorithm.