• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.11
• /
• pp.1868-1878
• /
• 2016

This paper proposes a novel velocity estimator for long-term underwater navigation of autonomous underwater vehicles(AUVs). Provided that an external position fix is not given, a viable goal in designing a underwater navigation algorithm is to reduce the divergence rate of position error only using the sporadic velocity information obtained from Doppler velocity log(DVL). For such case, the performance of underwater navigation eventually depends on accuracy and reliability of external velocity information. This motivates us to devise a velocity estimator which can drastically enhance the navigation performance even when the DVL measurement is unavailable. Incorporating the Gertler-Hagen hydrodynamics model of an AUV with the measurement models of velocity and depth sensors, the velocity estimator design problem is resolved using the extended Kalman filter. Different from the existing methods in which an AUV simulator is regarded as a virtual sensor, our approach is less sensitive to the model uncertainty often encountered in practice. This is because our velocity filter estimates the simulator errors with sensor aids and furthermore compensates these errors based on the indirect feedforward manner. Through the simulations for typical AUV navigation scenarios, the effectiveness of the proposed scheme is demonstrated.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.4 s.316
• /
• pp.1-7
• /
• 2007

When the sensor geometry is poor, the user position estimate obtained by of GN (Gauss-Newton) method is often diverged in radio navigation. In other to avoid divergence problem QCLS (Quadratic Correction Least Square) method using TDOA (Time Difference of Arrival) measurements is introduced, but the estimation error is somewhat large. This paper presents the modified QCLS method using weighted least square. Since the weighting matrix is influenced by the unknown user position, two-step approach is employed in the proposed method. The weighting matrix is estimated in the first step using least square, and then find user position is obtained using weighted least square. Simulation results show that the performance of the proposed method is superior to the conventional QCLS all over the workspace.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.9
• /
• pp.820-827
• /
• 2014

One of the basic problems in Wireless Sensor Networks (WSNs) is the localization of the sensor nodes based on the known location of numerous anchor nodes. WSNs generally consist of a large number of sensor nodes and recording the location of each sensor nodes becomes a difficult task. On the other hand, based on the application environment, the nodes may be subject to mobility and their location changes with time. Therefore, a scheme that will autonomously estimate or calculate the position of the sensor nodes is desirable. This paper presents an intelligent localization scheme, which is an artificial neural network (ANN) based localization scheme used to estimate the position of the unknown nodes. In the proposed method, three anchors nodes are used. The mobile or deployed sensor nodes request a beacon from the anchor nodes and utilizes the received signal strength indicator (RSSI) of the beacons received. The RSSI values vary depending on the distance between the mobile and the anchor nodes. The three RSSI values are used as the input to the ANN in order to estimate the location of the sensor nodes. A feed-forward artificial neural network with back propagation method for training has been employed. An average Euclidian distance error of 0.70 m has been achieved using a ANN having 3 inputs, two hidden layers, and two outputs (x and y coordinates of the position).

• Journal of Biosystems Engineering
• /
• v.36 no.2
• /
• pp.116-121
• /
• 2011

This study was conducted to develop a robust navigator which could be in positioning for precision farming through developing a plural GPS receiver with 4 sets of GPS antenna. In order to improve positioning accuracy by integrating GPS signals received simultaneously, the algorithm for processing plural GPS signal effectively was designed. Performance of the algorithm was tested using a simulation program and a fixed point on WGS 84 coordinates. Results of this study are aummarized as followings. 1. 4 sets of lower grade GPS receiver and signals were integrated by kalman filter algorithm and geometric algorithm to increase positioning accuracy of the data. 2. Prototype was composed of 4 sets of GPS receiver and INS components. All Star which manufactured by CMC, gyro compass made by KVH, ground speed sensor and integration S/W based on RTOS(Real Time Operating System)were used. 3. Integration algorithm was simulated by developed program which could generate random position error less then 10 m and tested with the prototype at a fixed position. 4. When navigation data was integrated by geometrical correction and kalman filter algorithm, estimated positioning erros were less then 0.6 m and 1.0 m respectively in simulation and fixed position tests.

• Journal of Navigation and Port Research
• /
• v.41 no.5
• /
• pp.297-302
• /
• 2017

The tracking filter plays a key role in accurate estimation and prediction of maneuvering the vessel's position and velocity. Different methods are used for tracking. However, the most commonly used method is the Kalman filter and its modifications. The ${\alpha}-{\beta}-{\gamma}$ filter is one of the special cases of the general solution provided by the Kalman filter. It is a third order filter that computes the smoothed estimates of position, velocity, and acceleration for the nth observation, and predicts the next position and velocity. Although found to track a maneuvering target with good accuracy than the constant velocity ${\alpha}-{\beta}$ filter, the ${\alpha}-{\beta}-{\gamma}$ filter does not perform impressively under high maneuvers, such as when the target is undergoing changing accelerations. This study aims to track a highly maneuvering target experiencing jerky motions due to changing accelerations. The ${\alpha}-{\beta}-{\gamma}$ filter is extended to include the fourth state that is, constant jerk to correct the sudden change of acceleration to improve the filter's performance. Results obtained from simulations of the input model of the target dynamics under consideration indicate an improvement in performance of the jerky model, ${\alpha}-{\beta}-{\gamma}-{\eta}$ algorithm as compared to the constant acceleration model, ${\alpha}-{\beta}-{\gamma}$ in terms of error reduction and stability of the filter during target maneuver.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.4
• /
• pp.469-475
• /
• 2015

This paper describes about the method for designing an extended Kalman filter to accurately measure the position of the spatial-phase system using a semiconductor sensor. Spatial position is expressed by the correlation of the rotated coordinate system attached to the body from the inertia coordinate system (a fixed coordinate system). To express the attitude, quaternion was adapted as a state variable, Then, the state changes were estimated from the input value which was measured in the gyro sensor. The observed data is the value obtained from the acceleration sensor. By matching between the measured value in the acceleration sensor and the predicted calculation value, the best variable was obtained. To increase the accuracy of estimation, designation of the extended Kalman filter was performed, which showed excellent ability to adjust the estimation period relative to the sensor property. As a result, when a three-axis gyro sensor and a three-axis acceleration sensor were adapted in the estimator, the RMS(Root Mean Square) estimation error in simulation was retained less than 1.7[$^{\circ}$], and the estimator displayed good property on the prediction of the state in 100 ms measurement period.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.5
• /
• pp.160-172
• /
• 2018

The method of estimating a position using a GPS has been applied to various fields including a navigation system of an automobile. However, since it is difficult to measure GPS signals indoors, it is difficult to locate specific objects indoors such as a building or factory. To overcome these limitations, this study proposes a system for object location estimation based on Bluetooth5 for the management of materials in factories. The object position estimation system consists of a Bluetooth signal generator, a receiver, and a database server. A signal generator based on Bluetooth Low Energy(BLE) is attached to the material and a receiver is appropriately arranged inside the factory. In this study, we propose "Diagonal Survey Method", a 4 - axis survey algorithm using four receivers to reduce the error of existing trilateration method. The proposed algorithm showed good performance compared to the conventional trilateration and we verified the effectiveness of the proposed system and algorithm by performing the experiment by installing the system in the factory.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.2
• /
• pp.113-118
• /
• 2023

The WiFi fingerprint method for location estimation within the home has the advantage of using the existing infrastructure and estimating absolute coordinates, so many studies are being conducted. Existing studies have mainly focused on the study of localization algorithms, but the improvement of accuracy has reached its limits. However, since a wireless LAN receiver such as a smartphone cannot measure signals smaller than the reception sensitivity of radio signals, the position estimation error varies depending on the method of processing these values. In this paper, we proposed a method to increase the location estimation accuracy by pre-processing the received signal data of the measured wireless LAN router in various ways and applying it to the existing algorithm, and greatly improved accuracy was obtained. In addition, the preprocessed data was applied to the KNN method and the CNN method and the performance was compared.

• Proceedings of the KOSOMBE Conference
• /
• v.1994 no.12
• /
• pp.113-116
• /
• 1994

Estimation of the evoked potential using the iterated bispectrum and cross-correlation (IBC) has been tried for both simulation and real clinical data. Conventional time average (TA) method suffers from synchronization error when the latency time of the evoked potential is random, which results in poor SNR distortion in the estimation of EP waveform. Instead of EP signal average in time domain, bispectrum is used which is insensitive to time delay. The EP signal is recovered by the inverse transform of the Fourier amplitude and phase obtained from the bispectrum. The distribution of the latency time is calculated using cross-correlation between EP signal estimated by the bispectrum and the acquired signal. For the simulation. EEG noise was added to the known EP signal and the EP signal was estimated by both the conventional technique and bispectrum technique. The proposed bispectrum technique estimates EP signal more accurately than the conventional technique with respect to the maximum amplitude of a signal, full width at half maximum(FWHM). signal-to-noise-ratio, and the position of maximum peak. When applied to the real visual evoked potential(VEP) signal. bispectrum technique was able to estimate EP signal more distinctively. The distribution of the latency time may play an important role in medical diagonosis.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.6
• /
• pp.191-196
• /
• 2016

A development on the indoor positioning technologies and services has been proceeded very actively. Among the several positioning technologies, the TDOA(Time Difference of Arrival) technology using acoustic signal has the best positioning performance. Because so many people use their own smartphones, the location of the smartphone is important, and the TDOA technology should be employed to use the acoustic signal for the positioning. For the digital signal processing with the acoustic signal, the signal should be sampled, and as the sampling rate increases, the positioning accuracy could be improved instead of processing time burden. In this paper, the position estimation error according to the sampling rate is analyzed, and the appropriate sampling rate for the positioning system is proposed.