• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.9
• /
• pp.1-6
• /
• 1997

A transmission type phase shift attenuator has a poor reflection characteristics at an output port. And that is controlled by the current, its dynamic rnage decreases due to the current limitation. In this paper, to avoid such disadvantages, a reflection type low phase shift attenuator has been designed and measured. As a result, at a center frequency (1855MHz), the sreflection type low pahse shift attenuator has an attenuation of 30dB, within the limit of 3 phase shift and less than -17dB reflection characteristics at both input and output ports. And it demonstrates the peformance of the reflection type low phase shift attenuator is better than the transmission type phase shift attenuator with the same measurement specifications.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.4
• /
• pp.80-86
• /
• 1996

In order to decrease fuel comsumption rate and emissions, lean burn engine which has equipped swirl control valve, is investigated experimentally on the test bench. Single cylinder engine was used to test the combustion and emission performance with 4 kinds of swirl valve. Decrease in the carbon monoxide, hyerocarbon and specific fuel consumption was shown at the lean condition, which means that a good choice of swirl valve on the given intake port geometry can be used to increase the combustion efficiency and lean limit.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.73-79
• /
• 2002

The NO emissions at the exhaust manifo1d were investigated with a fast NO analyzer to investigate the cycle-by-cycle variations on NO emissions level and the dependence of NO emissions on combustion. The measurement was performed with a part load condition with respect to the mixture ratios and the changes in loads at 1800rpm. The averaged values were obtained during 200 cycles. We found that there is characteristic pattern in 70 emissions from exhaust port and it was possible to set a representative value with the data sampled during specific period. As the load increased, the characteristics of NO emissions were more dependent on combustion pressures. It was also analyzed that the correlation between combustion pressures and NO emissions for different equivalence ratios tends to increase as the mixture goes leaner, Furthermore, this correlation for the lean mixture near the lean limit seemed to be kept.

• Journal of the Korean Institute of Navigation
• /
• v.17 no.4
• /
• pp.73-87
• /
• 1993

As a result of accepting the '71 FUND Convention and enforcing the Oil Pollution Compensation Act 1992, we observed some benefits and costa. This paper analyses those benefits and costs and suggests se-veral key policy recommendations for the estasblishment of an effective oil pollution compensation regime in Korea. This paper identifies the said benefits and costs as follows : First, by establishing the oil pollu-tion compensation system as same as the international level, most of small and medium size of oil pollution damage which are caused by coastal tankers will be compensated by FUND. Second, most of oil pollution damage which are not covered by '69 CLC will be compensated by FUND. Third, some parts of FUND Contribution Fee and CRISTAL Contribution Fee to be charged by major oil companies will be doubled. However the limit of international oil pollution compensation system and the loophole outside the Oil Pol-lution Compensation Act 1992 suggest followings : 1) Radical risk management and insurance manage-ment of ocean going tanker owners, 2) Establishment of oil pollution claim settlement system, 3) Enforce-ment of crew and ship management for coastal tanker and 4) Establishment of Korean P & I Club.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.1384-1389
• /
• 2004

The primary objective of this paper is to examine the capacity of electrical transmission in electric railway feeding system. Although supply capacity of railway substation are sufficient and there is no accident, due to the electrical transmission limit of feeding line the voltage breakdown may occur when large capacity of electric load at feeding line exist. So, using multi-port analysis model, we draw P-V curve due to the length of feeding line, load, location and power factor of electric locomotive. And through case study, compare measurement result and simulation result

• Journal of the Korean Institute of Gas
• /
• v.11 no.4
• /
• pp.59-63
• /
• 2007

The purpose of this paper is to find optimum vent port of the booth for gas explosion experiment. Also, it is to understand the safety of the booth for explosion experiment which is installed to let the trainees for legal education which is managed by IGTT(Institute of gas technology training) blow the riskiness of explosion. Since the booth for gas explosion experiment is a confined space, we used the exhaust model for indoor explosion. As the result, it was safety calculated when the amount of leaking gas was close to the maximum of explosion limit on the explosion experiment.

• Journal of Fisheries and Marine Sciences Education
• /
• v.29 no.2
• /
• pp.415-421
• /
• 2017

This study is aiming to find one of working conditions for loading and unloading a large ship at game port. Firstly, for dynamic analysis of the moored ships, the motion characteristics of ship according to loading condition are figured out. The motion characteristics of ship is related to environmental factors such as current, wind, mooring line, fender and etc. As a result, it is ascertained through numerical simulation using the AQUA MARINE developed by ANSYS INC. This study might contribute to make a new method of mooring stability of target ship.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1169-1170
• /
• 2007

The primary objective of this paper is to examine the capacity of electrical transmission in electric railway according to the type of feeding system. Although supply capacity of railway substation are sufficient and there is no accident, due to the electrical transmission limit of feeding line the voltage breakdown may occur when large capacity of electric load at feeding line exist. So, using multi-port analysis model, we draw P-V curve due to feeding method, load, location and power factor of electric locomotive.

• Proceedings of the KIEE Conference
• /
• 2005.10c
• /
• pp.291-295
• /
• 2005

This paper presents the modeling of grounding system on Korean electric railway system. The system model is composed of the catenary system, the grounding-system, the sub-sectioning post, the fault point, the sectioning post, the autotransformer in the substation, and the electric vehicle. The increment of rail-ground voltage may be thought as an amplifier of danger on human body of equipment insulation. The rail-ground voltage on steady state and on fault condition should be under standard limit voltage. To analyze grounding system for steady state and fault condition on Korean railway, modeling for each railway system is performed by 10-port network model. Modeling and analysis of present grounding-system are important to protect human and electronic equipments. The examinations for systematic grounding-system are investigated.

• Journal of Navigation and Port Research
• /
• v.26 no.3
• /
• pp.289-294
• /
• 2002

The broadband high power 3-way combiner was designed and fabricated for the digital TV repeater. To achieve increase of the bandwidth and the high power capability, Wilkinson type power divider was adopted in our research. First of all, Wilkinson type power divider of equal-split and unequal-split were combined, and the characteristics of the four port in-phase power combiner was simulated for each thickness of dielectric substrates. As the results of simulation, the power combiner fabricated by using dielectric substrate of 120 mil-thickness has the characteristics as follows: insertion loss of less than -651 dB, reflection coefficient of less than -13 dB, isolation among the output ports of less than -15 dB, and pose difference among the output ports of smiler than 13$^{\circ}$. Therefore, this power combiner was possible to improve the limit of microstrip line width due to high impedance, the problem of power loss due to interaction between strip lines in a high power combiner and narrow bandwidth simultaneously. Furthermore, making broadband and high power could be achieved since the fabricated 3-way combiner has good characteristics of insertion loss, the reflection coefficient, separation between ports, and phase difference.