• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2008.04a
• /
• pp.191-197
• /
• 2008

In this study, as a fuel filter for automobiles, base paper which can filtrate the polluted particles must satisfy with the standards of each vehicle. and a filter of impregnation paper made that combining the base paper with the resin. Therefore, They were wanted to found out the factors that affect base paper and impregnation paper according to content of HPZ, Mulberry pulp(MP), Laub holze bleached kraft pulp(LBKP). The most important things we wanted to find out in base paper and impregnation paper test were weight, thickness, air permeability, burst and tensile strength, maximum pore size and mean pore size, stiffness. we wanted to measure a rate of change of these condition by adjusting a rate of mixing for HPZ, MP and LBKP. Moreover, It suited for an impregnation paper mixed with a rate of mulberry pulp 20%, HPZ 40% and LBKP 40%. Used resins in this study was Phenol, Acryl, PVAc. And as every resins, sample was divided into existence and nothing of embossing. as a fuel filter for automobiles, It was appeared that the suitable condition of base paper was a rate of mixing for HPZ(40%), MP(20%) and LBKP(40%).

• Membrane Journal
• /
• v.25 no.2
• /
• pp.180-190
• /
• 2015

PVDF (polyvinylidene fluoride) nanofiber has the advantages such as excellent strength, chemical resistance, nontoxic, non-combustibility. Flat membranes with 0.3 and $0.4{\mu}m$ pore size respectively, were manufactured by PVDF nanofiber, and then each spiral wound module was prepared with them. A woven paper was not included in preparing the module with $0.3{\mu}m$ pore size; however, it was included the module with $0.4{\mu}m$ pore size. The permeate fluxes and rejection rates of the two modules were compared using pure water and simulation solution including kaolin and humic acid. The recovery rate and filtration resistance were calculated after water back-washing. In addition, the effect of flow rate and trans-membrane pressure on treatment efficiency and filtration resistance were investigated for the spiral wound module with $0.4{\mu}m$ pore size.

• Korean Journal of Materials Research
• /
• v.31 no.3
• /
• pp.115-121
• /
• 2021

MnO2 can be potentially utilized as an electrode material for redox capacitors. The deposition of MnO2 with poor electrical conductivity onto porous carbons supplies them with additional conductive paths; as a result, the capacitance of the electrical double layer formed on the porous carbon surface can be utilized together with the redox capacitance of MnO2. However, the obtained composites are not generally suitable for industrial production because they require the use of expensive porous carbons and/or inefficient fabrication methods. Thus, to develop an effective preparation procedure of the composite, a suitable structure of porous carbons must be determined. In this study, MnO2/C composites have been prepared from activated carbon gels with various pore sizes, and their electrical properties are investigated via cyclic voltammetry. In particular, mesoporous carbons with a pore size of around 20 nm form a composite with a relatively low capacitance (98 F/g-composite) and poor rate performance despite the moderate redox capacitance obtained for MnO2 (313 F/g-MnO2). On the other hand, using macro-porous carbons with a pore size of around 60 nm increases the MnO2 redox capacitance (399 F/g-MnO2) as well as the capacitance and rate performance of the entire material (203 F/g-composite). The obtained results can be used in the industrial manufacturing of MnO2/C composites for supercapacitor electrodes from the commercially available porous carbons.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1C
• /
• pp.9-17
• /
• 2008

In this research, an analytical solution for the coefficient of permeability of soils during consolidation is suggested. The pore pressure and the flow rate measurements at different locations during consolidation are utilized. The void ratio and volume compressibility of soils under consolidation are also estimated. A large consolidation testing device, possible in both vertical and radial drainage is designed and manufactured. And consolidation test with kaolinite soils were performed under radially inward drainage direction. Pore pressures in varying radial distances and flow rate with time were measured as well as vertical deformations. From the test results, the changes of permeability, volume compressibility and void ratio under consolidation and their spatial variations are estimated. Thus the proposed solution is verified by comparing with the experimentally estimated test results. In addition, it is confirmed that permeability, void ratio and volume compressibility decrease as consolidation and loading steps progress. Also, these soil characteristics increase with radial distant from drainage boundary, where lowest values observed, and slightly decrease as approaching undrained boundary.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.2
• /
• pp.82-86
• /
• 2011

Lightweight aggregate which is composed of sintered polycrystalline materials usually has a certain portion of pores inside of it. Because of such a structural characteristics, it tends to that movement of water in aggregate shows an abnormal behavior against the change of outside environment. In general, water movement behavior is controlled by porosity, distribution of pore size; however, dense surface layer will also affect water movement behavior in case of artificially sintered aggregates. Factors affecting water movement behavior in the aggregate are pore distribution, pore shape, pre-wetting method, etc. In this study, absorption characteristics of aggregate under the pressure and absorption rate according to water dipping time are analyzed for the basis of pressure pumping of lightweight concrete. Two kinds of aggregates were used for the test: one is made by 'L' company in Germany and the other is of our own made at the pilot plant in Kyonggi University. Absorption rate of aggregate is measured according to water dipping time, vacuum pressure, and quenching condition. Absorption rate of aggregate with $300^{\circ}C$ quenching is higher than that of aggregate with 24 hr water dipping. Generally the more vacuum the higher water absorption rate. Water absorption rate of 'L' aggregate under -300 mmHg is 54 % higher than that of aggregate with 24 hr water dipping; however, only 2 % increase in water absorption was measured for the K622 and K73 which were of our own.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.02a
• /
• pp.59-70
• /
• 2000

본 연구에서는 콘관입속도가 콘관입시험 결과에 미치는 영향을 연구하기 위하여 LSU/CALCHAS(Louisiana State University Calibration Chamber System)를 이용한 미니 Piezocone의 관입시험이 수행되었으며 그 결과를 비교 분석하였다. 10회의 미니 Piezocone 관입시험이 Ko 조건에서 수행되었으며 33% kaolin, 67% sand mixture가 시료로 사용되었고, 콘관입속도 0.3, 0.6cm/sec, U1(filter element at the cone tip), U2(filter element above the cone base), OCR=1, 10 의 조건이 다양하게 적용되었다. 시험결과 Cone Resistance, Excess Pore Water Pressure, Sleeve Friction 은 U1, U2 두 종류의 콘에 대해서 모두 관입속도가 커짐에 따라 증가하였으나 OCR의 증가에 따라서는 감소하였으며 U1의 Excess Pore Water Pressure가 U2 경우보다 크게 측정되었다.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.48 no.5
• /
• pp.63-71
• /
• 2006

In the present study, the dynamic deformation characteristics of clay, including the effect of loading rate in large strain ranges, were examined by performing undrained cyclic triaxial test. The test results showed that the loading rate to failure decreased with increasing loading amplitude and decreasing loading frequency. While the stress-strain relationships was not affected by loading frequency, excess pore pressure was affected significantly with the change in loading frequency. The change for 0.1 Hz was larger for than that of 0.01 Hz, resulting in inclined effective stress paths. Furthermore, the lower the frequency was, the higher the excess pore pressure was in the first loading.

• Preventive Nutrition and Food Science
• /
• v.16 no.3
• /
• pp.261-266
• /
• 2011

Supercritical $CO_2$ pretreatment before dehydration leads to a faster dehydration rate. The best supercritical $CO_2$ pretreatment conditions for the most effective dehydration were $45^{\circ}C$, 25 MPa and $55^{\circ}C$, 25 MPa. Increasing pressure of the supercritical $CO_2$ pretreatment system tended to accelerate the dehydration rate more than increasing temperature did. Samples pretreated at higher temperatures and pressures showed greater shrinking and pore distribution on scanning electron microscopy. Control samples maintained their cell walls, whereas samples pretreated at higher temperatures and pressures showed more cell disruption, and more pores were observed. Pore sizes of control and pretreated samples were about 100 and $70{\sim}80\;{\mu}m$, respectively. Samples pretreated at higher temperatures and pressures had smaller pores and a denser distribution.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1528-1533
• /
• 2004

In this study, we have manufactured the LHP(Loop Heat Pipe) with sintered metal wick and investigated the working characteristics of LHP experimentally.Water was used as a working fluid and fill charge rate was changed. LHP basically consist of the separated vapor/liquid channels, evaporator having sintered metal wick(effective pore diameter :$16{\sim}19{\mu}m$), and condenser cooled by water. The diameter of vapor/liquid line tube are 3.2mm/6.35mm, respectively. Heat transfer rate and thermal resistance was represented to study the basic characteristics of LHP at each conditions

• Korean Journal of Materials Research
• /
• v.14 no.2
• /
• pp.157-162
• /
• 2004

The object of this research is to develop a carbon molecular sieve(below CMS) which can separate selectively to convert mixture gases spout at waste landfill into fuel. And this research is meaningful from the viewpoint of a quality improvement of CH$_4$ gas and an utilization of by-product. CMS was prepared using coconut shell powder as starting material and the effects of activators, temperature and modifier on the reaction were investigated in this research. Also, pore diameter, surface area of CMS and adsorption rate were measured and studied by cahn balance and ASAP2010. Its specific surface area and pore distribution were controlled easily at 800^{\circ}C and adsorption rate was very good. The CMS prepared in this research is shown to be able to separate landfill gases very effectively.