• 대한전자공학회논문지SP
• /
• 제44권2호
• /
• pp.93-101
• /
• 2007

정합과 노출 보정을 동시에 최적화하기 위하여 반복적인 정합 알고리듬인 Lucas-Kanade 알고리듬을 히스토그램 변환에 기초한 노출 보정 알고리듬과 접목하였다. 단순 회귀 모델에 기초하여 비매개변수 추정인 실험적 조건 평균과 그의 다항식 근사를 이용하여 노출 보정을 시도하였다. 제안한 동시 최적화 알고리듬은 각 최적화 과정의 분리화가 가능하므로 기존의 Mann이나 Candocia의 동시 최적화 알고리듬에 비하여 구현의 융통성 측면에서 유리하다. 투사 공간 변환 관계를 가지는 실영상 들을 가지고 모의실험을 수행한 결과에서 보면 노출 보정을 고려하지 않은 경우에 비하여 좋은 성능을 얻음을 확인할 수 있었다.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2006년도 춘계학술발표회 논문집
• /
• pp.77-81
• /
• 2006

GPS cannot determine random errors such as multipath and signal cutoff caused by surrounding environment that determines the visibility of satellites and the speed of data creation and transmission is lower than the speed of vehicles, it is difficult to determine accurate dynamic positions. Thus this study purposed to implement a method of deciding the accurate dynamic position of vehicles by combining AHRS (Attitude Heading Reference System) IMU (Initial Measurement Unit) based on low-priced MEMS (Micro Electro Mechanical System) in order to provide the information of attitude, position and speed at a high transmission rate without external help. This study conducted an initialization test to decide dynamic position using AHRS IMU sensor, and derived attitude correction angles of vehicles against time through regression analysis. The roll angle was $y=(A{\times}10^{-6})x^2 -(B{\times}10^{-5})x+Cr{\times}10^{-2}$ and the pitch angle was $y=(A{\times}10^{-6})x^2-(B{\times}10^{-7})x+C{\times}10^{-2}$, each of which was derived from second-degree polynomial regression analysis. It was also found that the heading angle was stabilized with variation less than $1^{\circ}$ after 60 seconds.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2001년도 춘계 학술대회 논문집 통권 4호 Proceedings of the 2001 KSRS Spring Meeting
• /
• pp.104-110
• /
• 2001

Ocean heat fluxes over a wide region are generally estimated by an aerodynamic bulk fromula. Though a remote sensing technique can be expected to estimated global heat flux, it is difficult to obtain air temperature and specific humidity at sea surface by a remote sensor. In this study present a new method with which to determine near-sea surface air temperature from in situ data. Also, These methods compared with other methods. A new method used a linear regression equation between sea surface temperature and air temperature of the buoys data. In this study new method is validated using observed monthly mean data at the Japan Meteorological Agency(JMA), National Data Buoy Center(NDBC) and Tropical Ocean-Global Atmosphere(TOGA)-Tropical Atmosphere Ocean(TAO) buoys. The result that bias and rmse are 0.28, 1.5$0^{\circ}C$ respectively. The correlation coefficient is 0.98. Also, to retrieve near-sea surface specific humidity(Q) from good nonlinear regression relationship between vapor pressure(Ea) of buoy data and air temperature, after obtained the third-order polynomial function, compared with that of estimated from SSM/I empirical equation by Schussel et al(1995). The result that bias and rmse are -1.42 and 1.75(g/kg).

• 한국도로학회논문집
• /
• 제15권4호
• /
• pp.21-29
• /
• 2013

PURPOSES : The objective of this study is to provide for the overall SPL (Sound Pressure Level) prediction model by using the NCPX (Noble Close Proximity) measurement method in terms of regression equations. METHODS: Many methods can be used to measure the traffic noise. However, NCPX measurement can powerfully measure the friction noise originated somewhere between tire and pavement by attaching the microphone at the proximity location of tire. The overall SPL(Sound Pressure Level) calculated by NCPX method depends on the vehicle speed, and the basic equation form of the prediction model for overall SPL was used, according to the previous studies (Bloemhof, 1986; Cho and Mun, 2008a; Cho and Mun, 2008b; Cho and Mun, 2008c). RESULTS : After developing the prediction model, the prediction model was verified by the correlation analysis and RMSE (Root Mean Squared Error). Furthermore, the correlation was resulted in good agreement. CONCLUSIONS: If the polynomial overall SPL prediction model can be used, the special cautions are required in terms of considering the interpolation points between vehicle speeds as well as overall SPLs.

• Journal of Welding and Joining
• /
• 제14권4호
• /
• pp.33-42
• /
• 1996

In recent years there has been a significant growth in the use of the automated and/or robotic welding system, carried out as a means of improving productivity and quality, reducing product costs and removing the operator from tedious and potentially hazardous environments. One of the major difficulties with the automated and/or robotic welding process is the inherent lack of mathematical models for determination of suitable welding process parameters. Partial-penetration, single-pass bead-on-plate welds were fabricated in 12mm AS 1204 mild steel flats employing five different welding process parameters. The experimental results were used to develop three empirical equations: curvilinear; polynomial; and linear equations. The results were also employed to find the best mathematical equation under weld bend width to assist in the process control algorithms for the Gas Metal Arc Welding(GMAW) process and to correlate welding process parameters with weld bead width of bead-on-plates deposited. With the help of a standard statistical package program. SAS, multipe regression analysis was undertaken for investigating and modeling the GMAW process, and significance test techniques were applied for the interpretation of the experimental data.

• 한국안전학회지
• /
• 제33권4호
• /
• pp.21-29
• /
• 2018

In many companies handling flammable liquids, explosion-proof electrical equipment have been installed according to the Korean Industrial Standards (KS C IEC 60079-10-1). In these standards, hazardous area for explosive gas atmospheres has to be classified by the evaluation of the evaporation rate of flammable liquid leakage. The evaporation rate is an important factor to determine the zones classification and hazardous area distance. However, there is no systematic method or rule for the estimation of evaporation rate in these standards and the first principle equations of a evaporation rate are very difficult. Thus, it is really hard for industrial workplaces to employ these equations. Thus, this problem can trigger inaccurate results for evaluating evaporation range. In this study, empirical models for estimating an evaporation rate of flammable liquid have been developed to tackle this problem. Throughout the sensitivity analysis of the first principle equations, it can be found that main factors for the evaporation rate are wind speed and temperature and empirical models have to be nonlinear. Polynomial regression is employed to build empirical models. Methanol, benzene, para-xylene and toluene are selected as case studies to verify the accuracy of empirical models.

• 한국입자에어로졸학회지
• /
• 제18권4호
• /
• pp.109-127
• /
• 2022

Recently, low-cost particulate matter (PM) sensors have been widely used in monitoring mass concentration. Maintaining the accuracy of the sensors is important and requires rigorous performance evaluation and calibration. In this study, two commercial low-cost PM sensors(LCS), Plantower PMS3003 and Plantower PMS7003, were evaluated in the laboratory and field with a reference-grade PM monitor (GRIMM 11-D). Laboratory evaluation was conducted with single/mixed particles of PSL (Poly Styrene Latex) in an acrylic chamber at 20℃ and relative humidity of 20%. Field evaluation was conducted inside a building of Yonsei University (Shinchon) from February 12 to March 31, 2022. In both evaluations, LCS measured values became different from reference measured values when the relative humidity was high or the outdoor air PM10/PM2.5 ratio was high. Based on the field evaluation, the LCS measured values were corrected through four different regression analysis models. As a result, the multivariate polynomial regression analysis model showed highest matching with the reference PM monitor (PM2.5 >0.9, PM10 >0.85). In this model, the PM10/PM2.5 ratio and relative humidity were chosen as independent variables.

• Journal of Medicine and Life Science
• /
• 제20권3호
• /
• pp.107-114
• /
• 2023

Epidemiological control of coronavirus disease 2019 (COVID-19) is needed to estimate the infection period of confirmed cases and identify potential cases. The present study, targeting confirmed cases for which the time of COVID-19 symptom onset was disclosed, aimed to investigate the relationship between intervals (day) from symptom onset to testing the cycle threshold (CT) values of real-time reverse transcription-polymerase chain reaction. Of the COVID-19 confirmed cases, those for which the date of suspected symptom onset in the epidemiological investigation was specifically disclosed were included in this study. Interval was defined as the number of days from symptom onset (as disclosed by the patient) to specimen collection for testing. A locally weighted regression smoothing (LOWESS) curve was applied, with intervals as explanatory variables and CT values (CTR for RdRp gene and CTE for E gene) as outcome variables. After finding its non-linear relationship, a polynomial regression model was applied to estimate the 95% confidence interval values of CTR and CTE by interval. The application of LOWESS in 331 patients identified a U-shaped curve relationship between the CTR and CTE values according to the number of interval days, and both CTR and CTE satisfied the quadratic model for interval days. Active application of these results to epidemiological investigations would minimize the chance of failing to identify individuals who are in contact with COVID-19 confirmed cases, thereby reducing the potential transmission of the virus to local communities.

• 대한의용생체공학회:의공학회지
• /
• 제30권5호
• /
• pp.401-411
• /
• 2009

In this paper, we correct pulse wave velocity(PWV) with heart-rate and derive regression equations to estimate intima-media thickness(IMT). Widely used methods for diagnosis of arteriosclerosis are IMT and PWV. Arterial wall stiffness determines the degree of energy absorbed by the elastic aorta and its recoil in diastole but there is not correlation between sclerosis and IMT in an existing study. In this study, we will correct PWV with heart-rate and get regression equation to estimate IMT using heart-rate correction index(HCI). We executed experiments for this study. Made up question of physical condition and measured electrocardiogram(ECG), photoplethysmogram (PPG) of finger-tip and toe-tip and ultrasound image of carotid artery. Calculated PWV and IMT using ECG, PPG and ultrasound image. We found that every p-value between PWV and IMT is not significant(<0.05). But p-value between IMT and HCI which is a corrected PWV using heart-rate is significant(>0.01). We use HCI and various measured parameter for estimating regression equation and apply backward estimation to select parameters for regression analysis. Result of backward estimation, found that only HCI is possible to derive proper regression equation of IMT. Relationship between PWV and IMT is the second order. Result of regression equation of E-H PWV is $R^2$=0.735, adj $R^2$=0.711. This is the best correlation value. We calculate error of its analysis for verification of earlobe PWV regression equation. Its result is RMSEP=0.0328, MAPE(%) = 4.7622. Like this regression analysis, we know that HCI is useful parameter and relationship between PWV, HCI and IMT. In addition, we are able to suggest possibility which is that we can get different parameter of prediction throughout just one measurement.

• Archives of Pharmacal Research
• /
• 제11권3호
• /
• pp.185-196
• /
• 1988

The inflence of hydrophilic vehicles on percutaneous absorption rate of griseofulvin was studied using intact skin of full thickness of hairless rat. The in vitro absorption rates were used as the characteristics for deciding the optimum formula of ointment vehicles. The optimum formula of vehicle compositions for maximum absorption rate was obtained from the polynomial regression equation and the two graphical techniques, contour graph and partial derivative graph. It was composed of sodium lauryl sulfate (1.65 W /W%), white petrolatum (16.5 W /W%), propylene glycol (12.0 W /W%), and stearyl alcohol (19.6W /W%). The experimental value obtained from the optimum formula and the prediction value were 33.99 and 33.87 ${\mu}g/\sqrt{min}$, respectively. From these results, it was believed that optimum formula for semisolid dosage forms could be obtained from the application of the optimization technique used in this study.