• 한국세라믹학회지
• /
• 제37권3호
• /
• pp.280-287
• /
• 2000

Adsorption behavior and amount of phenolic resin followed silica (SiO2) formation onto silicon nitride(Si3N4) surface were investigated using electrokinetic sonic amplitude (ESA) technique and with UV spectrometer, to fabricate Si3N4/SiC nano-composite based on reaction between SiO2 formed and phenolic resin absorbed onto Si3N4 particle. The amount of SiO2 formed and carbon from phenolic resin absorbed onto Si3N4 surface were calculated quantitatively to adjust the reaction between SiO2 and phenolic resin, resulting in no residual SiO2 and carbon. As a result, pre-heated tempeature for optimized reaction was below 25$0^{\circ}C$, in which there was no residual SiO2 and carbon.

• 한국세라믹학회지
• /
• 제25권2호
• /
• pp.125-130
• /
• 1988

The characteristics of the PZT/PMM and PZT/Butadiene composites with 3 dimensional network structure have been investigated as a function of the PZT volume fraction. The dielectric constants of the PZT composites increased linearly as the PZT volume fraction increased. However, they are not significantly affected by the polymer compliance. The piezoelectric d33 coefficients of the PZT/Butadiene are largest than the PZT/PMM because of the high elastic compliance which promotes stress transfer. The values of the mechanical quality factor adn frequency factor of the PZT/PMM composite are slightly larger, while the planar coupling factor is smaller, than the PZT/Butadiene composite. These results are due to strong interaction and mechanical coupling between PZT and PMM.

• Restorative Dentistry and Endodontics
• /
• 제43권4호
• /
• pp.40.1-40.10
• /
• 2018

Objectives: This study evaluated the microtensile bond strength (${\mu}TBS$) of polymer-ceramic and indirect composite resin with 3 classes of resin cements. Materials and Methods: Two computer-aided design/computer-aided manufacturing (CAD/CAM)-fabricated polymer-ceramics (Enamic [ENA; Vita] and Lava Ultimate [LAV; 3M ESPE]) and a laboratory indirect composite resin (Gradia [GRA; GC Corp.]) were equally divided into 6 groups (n = 18) with 3 classes of resin cements: Variolink N (VAR; Vivadent), RelyX U200 (RXU; 3M ESPE), and Panavia F2 (PAN; Kuraray). The ${\mu}TBS$ values were compared between groups by 2-way analysis of variance and the post hoc Tamhane test (${\alpha}=0.05$). Results: Restorative materials and resin cements significantly influenced ${\mu}TBS$ (p < 0.05). In the GRA group, the highest ${\mu}TBS$ was found with RXU ($27.40{\pm}5.39N$) and the lowest with VAR ($13.54{\pm}6.04N$) (p < 0.05). Similar trends were observed in the ENA group. In the LAV group, the highest ${\mu}TBS$ was observed with VAR ($27.45{\pm}5.84N$) and the lowest with PAN ($10.67{\pm}4.37N$) (p < 0.05). PAN had comparable results to those of ENA and GRA, whereas the ${\mu}TBS$ values were significantly lower with LAV (p = 0.001). The highest bond strength of RXU was found with GRA ($27.40{\pm}5.39N$, p = 0.001). PAN showed the lowest ${\mu}TBS$ with LAV ($10.67{\pm}4.37N$; p < 0.001). Conclusions: When applied according to the manufacturers' recommendations, the ${\mu}TBS$ of polymer-ceramic CAD/CAM materials and indirect composites is influenced by the luting cements.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2006년도 SMT/PCB 기술세미나
• /
• pp.53-76
• /
• 2006

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.5-13
• /
• 2006

Based on the inventions of continuous ceramic fibers, such as C, SiC, $Al_2O_3$ etc., by polymer precursor driven methods, there have been many efforts to fabricate ceramic continuous fiber reinforced composite materials with metals and ceramics matrices. The main purpose of the R & D efforts has been to produce materials for severe environments, including advanced energy systems, advanced transportation systems. The efforts have been started from the R & D of metal matrix composite materials and now the strong emphasis on ceramic matrix composites R & D can be recognized. This paper provides a brief review about the national efforts to establish advanced composite materials for future industries starting from mid 70s. C/Al and SiC/Al are the typical examples to be applied transportation systems and energy systems. The excellences in specific strength and overall mechanical properties, the excellences in environmental resistance make those materials as potential materials for advanced ocean construction and marine transportation systems. About the recent progress in ceramic fiber reinforced ceramic composites, advanced SiC/SiC composites including NITE-SiC/SiC will be introduced and the present status will be introduced.

• Bulletin of the Korean Chemical Society
• /
• 제33권9호
• /
• pp.2949-2954
• /
• 2012

Nano ZnO with an average size of 8 nm was prepared by thermal decomposition of zinc oxalate at $450^{\circ}C$. A series of based composite polymer electrolyte PEO-$LiClO_4$ and nano ZnO as a filler have been synthesized using solution cast technique, with varying the filler ratio systematically. XRD, DSC and FTIR studies have been conducted to investigate the structure and interaction of different groups in the composite polymer electrolyte. Effect of nano ZnO ceramic filler concentration on the structure of composites and their electrical properties (DC-conductivity, AC-conductivity, dielectric constant, dielectric loss and impedance) at different frequencies and temperatures was studied. Melting temperature ($T_m$) of PEO decreased with the addition of both $LiClO_4$ salt and nano ZnO filler due to increasing the amorphous state of polymer. All composite samples showed an ionic conductivity. The maximum room temperature ionic conductivity is found for $(ZnO)_{0.5}(PEO)_{12}(LiClO_4)$ composite sample. All the results are correlated and discussed.

• 한국소음진동공학회논문집
• /
• 제19권3호
• /
• pp.301-312
• /
• 2009

This paper presents a theoretical approach to calculate the resonant frequency of a thickness vibration mode in the radial direction for a 1-3 piezoelectric composite transducer of circular arch shape. For the composite transducer composed of a piezoelectric ceramic and a polymer, vibration parameters were derived according to the volume ratio of a ceramic, and a vibration characteristic equation was derived from the piezoelectric governing equations with adequate boundary conditions. The fundamental resonant frequencies were calculated numerically and verified by comparing them with those obtained from the finite element analysis and the experiment. The volume ratio and the thickness are more substantial than the curvature radius to determine the fundamental resonant characteristics, and the fundamental resonant frequency becomes higher for the larger volume ratio of the piezoelectric ceramic and for the smaller thickness.

• 한국세라믹학회지
• /
• 제40권2호
• /
• pp.159-166
• /
• 2003

퍼플루오르설포닐 플로라이드 나피온 레진과 mordenite를 이용하여 $100^{\circ}C$ 이상의 고온에서 작동하는 고분자 전해질형 연료건지용 전해질 막을 제조하고, 물리적 특성, proton전도도 및 단위 전지의 성능을 측정하였다. 나피온/mordenite복합체 막은 나피온 레진을 용융한 후, mordenite를 무게별로 첨가하여 제조하였다. 고온 영역에서 proton 전도도를 측정한 결과, mordenite 함량이 증가할수록 층상 구조를 갖는 mordenite내에 존재하는 층간수의 느린 탈수 속도 때문에 proton 전도도는 증가하였다. 또한, 단위 전지 성능 측정 결과로부터, $130^{\circ}C$의 작동 온도에서 l0wt% mordenite를 함유하고 있는 복합체 막이 전체 영역에 걸쳐 가장 높은 성능을 보임을 알 수 있었다. 이러한 결과는 같은 조건에서. l0wt% mordenite가 함유된 복합체 막 내부에 존재하고 있는 수분이 다른 조성의 막보다 더 많이 존재하게 되어, 복합체 막의 이온 전도도를 유지하기 때문이다. 따라서, 나피온/mordenite복합체 막은 $100^{\circ}C$이상에서 작동하는 고분자 전해질형 연료전지용 전해질 막으로서 적합하다고 생각된다.

• Transactions on Electrical and Electronic Materials
• /
• 제16권6호
• /
• pp.351-354
• /
• 2015

In this study, alumina plates 9~25 μm in size were used as thermal fillers, and epoxy resin was used as a polymer matrix. Oriented alumina plate/epoxy composites were prepared using a rolling method. The effect of ordering alumina plates increased with alumina plate size. The thermal conductivity and flexural strength of the composites were investigated. The horizontal thermal conductivity of the oriented composite was significantly higher than the vertical thermal conductivity. The horizontal thermal conductivity of the 75 wt% alumina content was 8.78 W/mk, although the vertical thermal conductivity was 1.04 W/mk. Ordering of the alumina plate using a rolling method significantly improved the thermal conductivity in the horizontal direction. The flexural strengths of the ordered alumina/epoxy composites prepared at different curing temperatures were measured.

• 전기화학회지
• /
• 제19권4호
• /
• pp.123-128
• /
• 2016

본 연구에서는 poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP)를 나노 크기의 $Al_2O_3$ 세라믹입자와 혼합하여 전기방사법으로 복합 겔 고분자 전해질을 제조하였다. $Al_2O_3$ 세라믹입자를 혼합한 복합 겔 고분자 전해질의 이온전도도는 $9.5{\times}10^{-2}Scm^{-1}$로, 순수한 PVdF-HFP 겔 고분자 전해질보다 높은 이온전도도를 나타내며 전기화학적 안정성도 5.2 V까지 개선하였다. 전기화학적 성능을 분석하기 위해서 $LiNi_{1/3}Mn_{1/3}Co_{1/3}O_2$ (NMC)양극과 함께 전지로 제작되었으며 순수 겔 고분자 전해질과 복합 겔 고분자 전해질 셀은 0.1C-rate에서 각각 $168.2mAh\;g^{-1}$과 $189.6mAh\;g^{-1}$의 방전 용량을 가지며 우수한 수명 특성을 보여 주었다. 따라서 고유전율 세라믹 입자의 복합화는 리튬 이온 겔 고분자 전지의 안정성과 전기화학적 특성을 향상시키는 좋은 대안이 될 것으로 판단된다.