• Applied Chemistry for Engineering
• /
• v.30 no.1
• /
• pp.23-28
• /
• 2019

We report a supercapacitor cable, which consists of three-dimensional (3D) porous graphene coated onto the surface of carbon thread. The 3D porous framework of graphene was constructed by microwave-activated process using a graphene oxide-coated carbon thread. The use of microwave irradiation enabled to convert graphene oxide into reduced graphene oxide without any reducing agents and activate graphene sheets into exfoliated and porous graphene sheets. Combining two wire electrodes with a polymer gel electrolyte successfully completed supercapacitor device in a form of cable construction. The supercapacitor cables were highly flexible, and thus can be transformed into various shapes of devices and be integrated into textile items. A high area-capacitance of 38.1 mF/cm was obtained at a scan rate of 10 mV/s. This capacitance was retained 88% of its original value at 500 mV/s. The cycle life was also demonstrated by repeating a charge/discharge process during 10,000 cycles even under bent states, showing a high capacitance retention of 96.5%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.2
• /
• pp.77-81
• /
• 2019

Recently, as the problem of environmental pollution emerges, various methods of eco-friendly water treatment method are being developed. Polymer membranes, which are currently leading the market, are inexpensive, but have many problems in terms of chemical resistance and durability. Thus, ceramic membrane has been attracted great attention as high-efficiency water treatment due to excellent durability and chemical resistant. In this study, ceramic membranes were developed via pore structure, size control, and surface treatment. The pore size of the membrane was controlled through the formation of $ZrO_2$ and $TiO_2$ coating films. Tape casting and sol-gel process were used to form a ceramic coating film with nanopores on the surface of the membrane. Microstructure analysis of ceramic membrane and pore size analysis of the coating film were conducted and the change of water treatment characteristics was observed.

• Applied Chemistry for Engineering
• /
• v.32 no.4
• /
• pp.403-408
• /
• 2021

In this study, a thin and flexible planar supercapacitor (PSC) was fabricated by coating polyaniline (PANI) on a screen-printed carbon electrode. Carbon ink was coated onto the flexible polyethylene terephthalate using a screen-printing method; subsequently, a thin film of PANI was coated onto the carbon surface using a dilute polymerization method. A thin flexible PANI electrode in an interdigitated structure was assembled with a polymer gel electrolyte that resulted in planar-shaped supercapacitor (PSC) devices. The as-obtained PANI/PSC was very thin and flexible, exhibiting a high areal capacitance of 409 µF/cm was obtained at a rate of 10 mV/s. This capacitance retains 46% of its original value at 500 mV/s. The flexible PANI/PSC exhibited an excellent capacitance retention of 82% even under bent states of 180° and 100 repetitive bent cycles.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.3
• /
• pp.223-229
• /
• 2010

In this study diverse dehydrogenative polymers (DHPs) were synthesized with three precursors of native lignin [p-coumaryl alcohol (PCA), coniferyl alcohol (CA), sinapyl alcohol (SA)] in the presence of horseradish peroxidase (HRP, EC. 1.11.1.7)/$H_2O_2$. To compare the structural features between DHPs and native lignin, the DHPs as well as pine/poplar milled wood lignins were simultaneously subjected to gel permeation chromatography (GPC) to determine average molecular weights and derivatization followed by reductive cleavage (DFRC) to investigate the frequency of ${\beta}$-O-4 linkage. The highest yield of DHP was measured to 71% when CA was solely injected (G-DHP) and the yield of H-DHP was 42%. However, single injection of SA could not form any polymer in this system. The average molecular weights of DHPs were ranged between 3,000~4,700, which were only 1/2 fold compared with that of pine MWL (G-type lignin: Mw 7,340) and 1/3 scale compared with that of poplar MWL (GS-type lignin: Mw 13,250). DFRC analysis revealed that the formation of ${\beta}$-O-4 linkage during dehydrogenative polymerization was the highest in the GS-DHP with ca. 502 ${\mu}mol$/g, which was, however, remained to only 50% compared to that in poplar MWL (1107 ${\mu}mol$/g). The ${\beta}$-O-4 linkage was estimated to ca. 286 ${\mu}mol$/g In the G-DHP, which was twice as much as that of H-DHP(127 ${\mu}mol$/g). Similar to GS-DHP, only half amount of ${\beta}$-O-4 linkage, compared to pine MWL, was formed during in vitro polymerization of CA by horseradish peroxidase/$H_2O_2$.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.3
• /
• pp.255-264
• /
• 2014

This study analyzes the cause and the repairing method of water leak by parts of basement parking lot which is recorded to have a high defect frequency in apartment buildings. It has been assessed that the cause of water leakage on the first floor upper substrate is due to such factors as landscaping and weights. During construction or through other cases, it has been determined that cracks were produced in the apartment structure because the structure was weak and exposed to the effects of the substrate movement. The base floor and underground external walls are areas that are exposed to water pressure (uplife pressure), thus in normal cases the rear surface repair of the structure using sythetic rubberized polymer gel should be considered as an effective method. However, in cases where application of waterproofing layer is required in the structure due to high water pressure, using asystolic cement milk grout to form the waterproofing layer and applying water-swelling acrylic material into the cracked areas is considered to be highly effective.

• Journal of Microbiology and Biotechnology
• /
• v.14 no.5
• /
• pp.985-990
• /
• 2004

Levans produced from Microbacterium laevaniformans were isolated, characterized, and fractionated by molecular weight. TLC, HPLC, and GC-MS analyses of the exopolysaccharide showed that it was a fructan-type polymer and was composed of (2,6)- and (2,1)-glycosidic linkages. $^{13}C$-NMR analysis proved that the polysaccharide was mainly a $\beta$-(2,6)-linked levan-type polysaccharide. To investigate the cytotoxicity of the acetone-precipitated levan fractions such as M1, M2, and M3, HepG2, P388D1, U937, SNU-1, and SNUC2A cell lines were screened. Among the cell lines tested, the cytotoxicity of M1- M3 fractions were detected from only SNU-1 and HepG2 cells at the dosage level of $100-800\mu\textrm{g}ml$. The M2 fraction M_r$, 80,000) at 400 $mu{g/ml}$ had the greatest cell growth inhibition (84.6%) on SNU-1, while the M1 $(M_r$, 50,000) at $800\mu\textrm{g}ml$ showed the greatest (46.32%) on HepG2. To obtain more uniform M_r$ fractions of levan, the levan was further fractionated from S1 $(M_r$ 1,000,000) to S5 $(M_r$ 10,000) using gel permeation chromatography. Again, the S1-S5 fractions had strong cytotoxicity on SNU-1 and HepG2 cell lines. The greatest inhibition effects of S4 $(M_r$ 80,000) on SNU-1 and S5 $(M_r$ 10,000) on HepG2 were shown to be 49.5% and 73.0%, respectively. The cytotoxicity of the levan fractions was more effective on SNU-1 than on HepG2. Although the relationship between the Mw and the cytotoxicity was not clear, smaller $M_r$, fractions of levan showed greater growth inhibition effect on the cancer cell lines in general. Therefore, it was indicated that a specific Mw class of levan is responsible for the effective cytotoxicity.

• Journal of Pharmaceutical Investigation
• /
• v.35 no.6
• /
• pp.417-422
• /
• 2005

This study was aimed to design and formulate the moisture-activated patches containing ofloxacin and lidocaine for antibacterial and local anesthetic action. The solubility of lidocaine at $32^{\circ}C$ in various vehicles decreased in the rank order of PG $759.5{\pm}44.5\;mg/mL$ > PGL > IPM > PEG 300 > PEG 400 > Ethanol > PGMC > DGME > PGML > OA > $Captex^{\circledR}\;300$ > $Captex^{\circledR}\;200$ > water $(4.0{\pm}0.1\;mg/mL)$. Ofloxacin revealed very low solubility, which the highest solubility was obtained from PEG 400 $(18.7{\pm}6.3\;mg/mL)$ among the vehicles used. The addition of lactic acid increased the solubility of ofloxacin dramatically; the solubility at 5% lactic acid was $133.7{\pm}9.7\;mg/mL$. As $2-hydroxypropyl-{\beta}-cyclodextrin$ was added at the concentrations of 40, 80, 120, 160 and 200 mM, the solubilities of lidocaine and ofloxacin were enhanced up to three and two times, respectively, with concentration-dependent pattern. Gel intermediates for filmtype patches were prepared with mucoadhesive polymer, viscosity builders, lidocaine or ofloxacin at pH values from 5 to 7. Gels were cast onto a release liner and dried at room temperature. Dried patch was attached onto an adhesive backing layer, thus forming a patch system. Patches containing a single drug component were characterized by in vitro measurement of drug release rates through a cellulose barrier membrane. The release study was carried out at $37^{\circ}C$ using a Franz-type cell. Receptor solutions were isotonic phosphate buffers (pH 7.4). Samples $(100\;{\mu}L)$ were taken over 24 hours and quantitated by a verified HPLC method. The releases from all tested were proportional to the square root of time. The release rates were 0.9, 157.3 and $281.7\;{\mu}g/cm^{2}/min^{1/2}$ for the lidocaine patches and 19.8,37.2 and $50.7\;{\mu}g/cm^{2}/min^{1/2}$ for the ofloxacin patches at the concentrations of 0.3, 0.5 and 1 %, respectively. The release rates were dose dependent in both drug patches $(R^{2}\;=\;0.9077\;for\;lidocaine;\;R^{2}\;=\;0.9949\;for\;ofloxacin)$ and those were also thickness-dependent $(R^{2}\;=\;0.9246\;for\;lidocaine;\;R^{2}\;=\;0.9512\;for\;ofloxacin)$.

• Journal of Integrative Natural Science
• /
• v.2 no.1
• /
• pp.18-23
• /
• 2009

This minireview provides the chosen examples of our recent discoveries in the polymerization of hydrosilanes, dihydrosilole, lactones, and vinyl derivatives using various catalysts. Hydrosilanes and lactones copolymerize to give poly(lactone-co-silane)s with $Cp_2MCl_2$/Red-Al (M = Ti, Zr, Hf) catalyst. Hydrosilanes (including dihydrosilole) reduce noble metal complexes (e.g., $AgNO_3$, $Ag_2SO_4$, $HAuCl_4$, $H_2PtCl_6$) to give nanoparticles along with silicon polymers such as polysilanes, polysilole, polysiloxanes (and silicas) depending on the reaction conditions. Interestingly, phenylsilane dehydrocoupled to polyphenylsilane in the inert nitrogen atmosphere while phenylsilane dehydrocoupled to silica in the ambient air atmosphere. $Cp_2M/CX_4$ (M = Fe, Co, Ni; X = Cl, Br, I) combination initiate the polymerization of vinyl monomers. In the photopolymerization of vinyl monomers using $Cp_2M/CCl_4$ (M = Fe, Co, Ni), the photopolymerization of MMA initiated by $Cp_2M/CCl_4$ (M = Fe, Co, Ni) shows while the polymerization yield decreases in the order $Cp_2Fe$ > $Cp_2Ni$ > $Cp_2Co$, the molecular weight decreases in the order $Cp_2Co$ > $Cp_2Ni$ > $Cp_2Fe$. For the photohomopolymerization and photocopolymerization of MA and AA, the similar trends were observed. The photopolymerizations are not living. Many exciting possibilities remain to be examined and some of them are demonstrated in the body of the minireview.

• KSBB Journal
• /
• v.21 no.4
• /
• pp.279-285
• /
• 2006

We investigated the effects of immobilization chemistry on the yield of immobilization and the bioactivity of the immobilized enzymes. Trypsin as a model protein and macroporous polymer beads(Toyopearl AF 650M, Tosho Co., Japan) was used as a model matrix. Four methods were used to immobilize trypsin; covalent conjugation by reductive amination(at pH 10.0 and pH 4.0) and affinity interaction via streptavidin-biotin, and double-affinity interaction via biotin-streptavidin-biotin system. The covalent conjugation immobilized $3{\sim}4$ mg/ml-gel, ca. 3-fold higher than the affinity method. However, the specific activity of the covalently(pH 10.0) and affinity-immobilized trypsin(via streptavidin-biotin) are ca. 37% and 50%, respectively, of that of the soluble enzyme(on the low-molecular-weight BAPNA substrate). When the molecular size of a substrate increased, the affinity-immobilized trypsin showed higher clavage activity on insulin and BSA. This result seemed to indicate the streptavidin-biotin system allowed more steric flexibility of the immobilized trypsin in its interaction with a substrate molecule. To confirm this, we studied the molecular flexibility of immobilized trypsin using quartz crystal microbalance-dissipation. Self-assembled monolayers were formed on the Q-sensor surface by aminoalkanethiols, and gultaraldehyde was attached to the SAMs. Trypsin was immobilized in two ways: reductive amination(at pH 10.0) and the streptavidin-biotin system. The dissipation shift of the affinity-immobilized trypsin was $0.8{\times}10^{-6}$, whereas that of the covalently attached enzyme was almost zero. This result confirmed that the streptavidin-biotin system allowed higher molecular flexibility. These results suggested that the bioactivity of the immobilized enzyme be strongly dependent on its molecular flexibility.

• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.857-862
• /
• 1999

Aminated poly(ether sulfone)(APES) was prepared by amination of nitrated poly(ether sulfone)(NPES) after poly(ether sulfone)(PES) was nitrated with mixed acid of nitric acid and sulfuric acid(sulfuric acid is a catalyst). As a results of the FT-IR spectrum analysis, the nitration of PES was confirmed by the bands of asymmetric stretching and symmetric stretching of $NO_2$ group at 1537 and $1351cm^{-1}$, respectively. Also when the NPES was aminated, it was disappeared to absorbance peaks of $NO_2$ group. And It was confirmed by the bands of asymmetric stretching and symmetric stretching of $NH_2$ group at 3470 and $3374cm^{-1}$, respectively. The optimum condition of the nitration on PES(5 g; 21.55 mmol.) was 12 hr of reaction time, $120^{\circ}C$ of reaction temperature, nitric acid of 28.00 mmol. and sulfuric acid of 52.00 mmol. As a result of the elemental analysis of APES, reapeating unit per amine groups were induced to 0.89. The adsorption rate of NO gas was lower than that of silica gel and active carbon. But the adsorption capacity of NO gas was higher than that of these. When the APES was absorbed to NO gas, the chemical adsorption rate was lower than the physical adsorption rate. But the chemical adsorption capacity of it was higher than physical adsorption capacity.