• Journal of the Korean Society of Food Science and Nutrition
• /
• v.13 no.1
• /
• pp.15-21
• /
• 1984

In order to ascertain the practical possibility of home made retort pouches for production of retort pouch foods in factory, two kinds of retortable pouches, i. e. 3 ply film (polyester film/Al. foil/casting polypropylene) and 4 ply film(polyester film/Al. foil/nylon/casting poll·propylene) were developed in Korea, and then, their physical properties, such as physical strength, heat resistance during thermal processing and preservability of foods and sanitary safety, were tested and compared with the foreign made pouches. The results obtained were summarized as follows. a. The physical strength of home made retort pouches in processing model foods(soybean oil 5 %, acetic acid 2%, starch 5 % and water to 100 %) was equal to that of foreign made pouches at accelerated examination condition($38^{\circ}C$, 98 % RH). But the lamination strength of home made products was a little bit superior to that of foreign made products. b. Home made retort pouches(SAMA-4 ply and SAMA-3 ply pouch) packed with rice or curry was possible to bear the thermal processing at $135^{\circ}C$ and shelf-life was one year or more at ambient temperature($20^{\circ}C$). c. Sanitary safety test showed that these home made retort pouches were acceptable comparing to the regulation recommended by the Ministry of Health and Social Affairs.

• Applied Chemistry for Engineering
• /
• v.19 no.4
• /
• pp.388-396
• /
• 2008

2 Components polyurethane coatings are widely used for the industrial coating in general because of its excellent film performance and the workability which were brought by the 3 dimensional cross linked chain structures being formed after the reaction between polyol and polyisocyanate. 2 components polyurethane can be classified into alkyd polyol, polyester polyol, acrylic polyol and polyester modified acrylic polyol depending on where it is used. This research was conducted under the conditions below; different chemical compositions of resin for paint, set the same conditions of viscosity, thinner and acid value, set alternative polyols, OH values and catalysts, set alternative polyisocyanate hardeners of the paint, measure the reaction rates and dynamic mechanical characteristics using RPT-3000, Rotation Rheometer, DMA and FTIR. The research found that the reactivity between polyol and isocyanate influences the film performance and workability depending on the catalysts, OH values and chemical compositions. We find out that different reaction rate of acrylic polyol and polyester modified acrylic polyol with poly-isocyanate is not influenced on temperature and catalyst. In addition, reaction speed of high hydroxyl content polyol is faster than low hydroxyl equivalent. These results can improve difficult working condition to apply urethane coating.

• Journal of Mechanical Science and Technology
• /
• v.16 no.10
• /
• pp.1222-1228
• /
• 2002

This research is the development of a flexible tactile sensor array for service robots using PVDF (polyvinylidene fluoride) film for the detection of a contact state in real time. The prototype of the tactile sensor which has 8${\times}$8 array using PVDF film was fabricated. In the fabrication procedure, the electrode patterns and the common electrode of the thin conductive tape were attached to both sides of the 281$\mu\textrm{m}$ thickness PVDF film using conductive adhesive. The sensor was covered with polyester film for insulation and attached to the rubber base for a stable structure. The proposed fabrication method is simple and easy to make the sensor. The sensor has the advantages in the implementing for practical applications because its structure is flexible and the shape of the each tactile element can be designed arbitrarily. The signals of a contact force to the tactile sensor were sensed and processed in the DSP system in which the signals are digitized and filtered. Finally, the signals were integrated for taking the force profile. The processed signals of the output of the sensor were visualized in a personal computer, and the shape and force distribution of the contact object were obtained. The reasonable performance for the detection of the contact state was verified through the sensing examples.

• Journal of the Korean Magnetics Society
• /
• v.7 no.6
• /
• pp.314-320
• /
• 1997

We have observed the orientation behavior of acicular iron oxides in magnetic layer of the particular magnetic tape after magnetic paint was coated on polyester film. As results of the static orientation, orientation of iron oxides come to the maximum at the front and the back of orientation magnets, but it was a litter lower at the back than at the front, and it slowly decreases and come to the constant level after passing through the orientation magnets. In case of edge portion to be futher away from center in the coated film, the orientation of iron oxides in magnetic layer come to worse than that of the center. We think it is owing to the shape and the magnetic magnitude of orientation magnets. The results of the dynamic orientation are as follows. As the orientation of iron oxides in the particulated magnetic tape is higher, the output properties of tape come to better than ever. And the orientation of iron oxides can be changed by drying condition, as result, the output properties of tape can be also. Therefore we think the considrations of the design of orientation magnets and the control of drying condition are needed to improve output properties of the particulated magnetic tape.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.17 no.4
• /
• pp.299-305
• /
• 1984

As one trials to utilize sea mussel and anchovy effectively, powdered instant soups were prepared and then their quality stability were examined during storage. Powdered instant soup was made by adding $3\%$ sugar, $20\%$ table salt, $5\%$ monosodium glutamate, $0.2\%$ black pepper and garlic powder to the pulverized dried sea mussel or anchovy. Powdered instant soup products, powderd products, and dried round state sea mussel or anchovy were packed with air in laminated film bag (cellophane/polyester/aluminium foil/polyester: $20{\mu}m/15{\mu}m/7{\mu}m/20{\mu}m,\;13{\times}14cm$). The contents of amino-nitrogen and volatile basic nitrogen of these products were showed little significant variations and also water activity and color value (L, a, b) of these products were little changed during storage. Thiobarbituric acid value increased up to 30 days of storage and then decreased slightly. Comparing the quality of powdered-seasoned products with that of dried round state products, there were no significant differences in stability during storage. Judging from the experimental results, the quality of powdered instant soup of sea mussel and anchovy were stable for 100 days at room temperature($25{\pm}3^{\circ}C$).

• Korean Journal of Food Science and Technology
• /
• v.20 no.3
• /
• pp.363-370
• /
• 1988

An attempt was made in this study to investigate the possibility of processing oyster and sea mussel into an intermediate moisture food. To obtain a palatable and instant product, shucked samples were heated in soy sauce for 5 min., heated in seasoning solution for 10 min., and then dried by the method of hot-air blowing for 4-6 hours at $40^{\circ}C$. Optimum seasoning solutions consisted of 2% monosodium glutamate, 3.5% sodium chloride, 15% sorbitol, 2% propylene glycol, 5% glycine and 0.02% rosemary oleoresin in 72.48% water. Judging from water activity, thiobarbituric acid, viable cell count, volatile basic nitrogen, surface color and sensory evaluation, vacuum-packaging method in nylon/PE $(20{\mu}m/40{\mu}m)$ or polyester/viniliden chloride/polypropylene $(12{\mu}m/15{\mu}m/50{\mu}m)$ film bag did hardly damage to the quality of intermediate moisture products, but air-packaging method in polyethylene(0.06m/m) bag did considerable damage to the quality during storage for 60 days in an incubator with 49-51% relative humidity at $30^{\circ}C$.

• Journal of the Korean Applied Science and Technology
• /
• v.22 no.3
• /
• pp.270-280
• /
• 2005

To maximize a synergy effect in flame-retardancy of flame-retardant coatings, phosphorus and chlorine were introduced in polymer chains. Two-components PU flame-retardant modified polyesters (ABTTC-10C, -20C, -30C) were prepared by curing, at room temperature, of isocyanate (allophanate-trimer) and prepared modified polyesters which contain phosphorus and chlorine. To examine the film properties of the prepared flame-retardant coatings, film specimens were prepared with the prepared coatings. The film properties of ABTTC, ABTTC-10C and ABTTC-20C, which contain 0, 10 and 20wt%, 2,4-dichlorobenzoic acid (2,4-DCBA), respectively, were proved to be good, whereas the film properties of ABTTC-30C, which contains 30wt% 2,4-DCBA, were proved to be a little bit poor. Two kinds of flame retardancy tests, $45^{\circ}$Meckel burner method and LOI method, were performed. With the $45^{\circ}$Meckel burner method, three flame-retardant coatings except ABTTC showed less than 3.4 cm of char length, and showed less than 2 seconds of afterflaming and afterglow. From this result, the prepared flame-retardant coatings were proved to have the 1st grade flame retardancy. With the LOI method, the LOI values of the coatings containing more than 10wt% 2,4-DCBA were higher than 30wt%, which means that the coatings possess good flame-retardancy. From these results, it was found that synergistic effect in flame-retardancy was taken place by the introduced phosphorus and chlorine.

• Journal of Environmental Science International
• /
• v.22 no.2
• /
• pp.243-249
• /
• 2013

Fibers of microbial polyesters, poly(3-hydroxy butyrate) (PHB) and poly(3-hydroxy butyrate-co-3-hydroxy valerate) (HB-co-HV) were prepared by electrospinning method. The obtained fibers were evaluated by differential scanning calorimetry, scanning electron microscopy, and oil absorption. The formation of fibers was strongly dependent on a concentration of solution. At a low concentration, the fibers contained beads which is from aggregation of polymer due to short evaporation time. The fine fibers with $2-5{\mu}m$ diameter were obtained at 20 wt% concentration. The contact angle measurement showed that the fiber had higher water contact angle than the film due to the lotus-like effect. Oil absorbency showed that the fiber had higher than the film. Specially, the HB-co-HV fiber which was spinned from 20 wt% absorbed 65% oil which is much higher than that of a normal polypropylene-based oil paper.

• Journal of Sericultural and Entomological Science
• /
• v.43 no.1
• /
• pp.41-48
• /
• 2001

The purification, dissolution and powdering of stained waste silk obtained from weaving and dyeing process were studied for the surface modification of textile fabric and plastic materials. The whiteness of stained waste silk could be improved through degumming and bleaching with sodium hydrosulfite. The water-soluble fibroin solution can be obtained by dissoving the degummed waste silk in a boiling solution of 50% calcium chloride for 60 minutes. The salts and heavy metals contained in fibroin solution were removed by electric dialysis, wool fiber filtration and gel filtration chromatography. The fibroin powder was prepared by using a fine grinder after the alkali treatment for weakening the silk fiber. The fine fibroin powder of particle size around 30 ㎛ was obtained with a ultra fine-mill, while it was finer below 10 ㎛ with a ball-mill. The dissolved or powdered silk was applied to the surface of fabric with addition of the binder (a urethane resin). The moisture content of polyester and nylon fabrics treated with the silk solution was improved due to hygroscopic property of silk. The fine fibroin powder mixed with the binder ws coated on the surface of synthetic film by use of the air pressed sprayer. It was revealed that the hygroscopicity as well as the softness of fibroin powder coated film was much improved. Therefore, it is thought that the fine silk fibroin powder is applicable as an coating agent for the surface modification of plastic and synthetic leather.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.316-320
• /
• 2009

UV curable hard and color coatings were formed on polycarbonate(PC) films. The coating materials were composed of a commercially available end-capped polyester(EB830), diacrylate monomer(HDDA), silicon acrylate, photoinitiator, and organic dye as a coloring agent. The surface properties of coating films were evaluated, and the influences of the compositions of coating materials were investigated. The coating films showed high transmission and good adhesion between coating layer and PC substrate. And the coating films exhibited higher hardness than bare PC film. The coating films with various colors were obtained by wet process, and the clear and color window lenses for mobile phone were prepared successfully.