• Fashion & Textile Research Journal
• /
• v.10 no.2
• /
• pp.254-259
• /
• 2008

Poly(ethylene-co-vinylacetate)(EVA) microspheres were prepared by a thermally induced phase separation. The microsphere formation occurred by the nucleation and growth mechanism in the metastable region. The diluents used were toluene. The microsphere formation and growth was followed by the cloud point of the optical microscope measurement. The microsphere size, which was obtained by SEM observation and particle size analyzer, became decreased when the titanium dioxide($TiO_2$) concentration was higher. The deodorizing function of the prepared fabrics was studied by the determination of the decomposing capability for $NH_3$. The deodorant activity of these deodorizing fabrics was measured by chromogenic gas detector tubes. The deodorant activity of $NH_3$ increased with increasing $TiO_2$ concentration of EVA microsphere.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.1
• /
• pp.211-217
• /
• 2014

A new needle-based device for headspace wire coated in-needle microextraction (HS-WC-INME) was fabricated using a nichrome wire coated with poly(ethylene glycol) (PEG) and poly(dimethylsiloxane) (PDMS) mixture. The proposed needle device was applied for the determination of volatile compounds in lavender and lavandin essential oils by gas chromatography. Fundamental parameters such as needle design, conditions of extraction and desorption were optimized along with the validation of the extraction and desorption efficiency. The optimal conditions were 30 min extraction at $50^{\circ}C$ and 2 min desorption at $240^{\circ}C$. The calibration curves showed good linearity with the suitable values of the coefficients of determination ($r^2$) greater than 0.99. The limits of detection for linalyl acetate, ${\beta}$-caryophyllene, linalool and (+)-limonene were 7.15, 9.04, 10.79 and 22.26 ng, respectively. Analytical recoveries were acceptable in the test samples, varying from 86.7% to 108.0%. The values of relative standard deviations for run to run showed range less than 0.9% while 3.9% through 7.2% for needle to needle. The proposed PEG-PDMS coating could be more suitable than PDMS coating to extract particular polar groups such as alcohols.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2005.09a
• /
• pp.83-88
• /
• 2005

유기 절연층을 갖는 유기 박막트랜지스터 (organic TFT)를 제작하여 소자 성능을 조사하였다. 유기 절연층의 형성에서는 polyvinyl 계열의 PVP(poly-4-vinylphenol)와 PVT(polyvinyltoluene)를 용질로, PGMEA (propylene glycol mononethyl ether acetate)를 용매로 사용하였다. 또한, 열경화성 수지인 poly(melamine-co-formaldehyde)를 경화제로 사용하여 유기 절연층의 cross-link 를 시도하였다. MIM 구조로 유기 절연층의 특정을 측정한 결과, PVT는 PVP에 비해 절연 특성이 떨어지는 경향을 보였다. 게이트 절연막의 제작에서 PVP를 cobpolymer 방식과 cross-linked 방식으로 실험 해 본 결과, cross-link 방식에서 낮은 누설전류 특성을 나타내었다. OTFT 제작에서는 PVP를 용질로, poly(melanine-co-formaldehyde)를 경화제로 사용한 cross-linked PVP 를 게이트 절연막으로 이용하였다. PVP copolymer($20\;wt\%$)에 $10\;wt\%$ poly(melamine- co-formaldehyde)를 혼합한 cross-linked PVP 를 게이트 절연막으로 사용하여 top contact 구조의 OTFT를 제작한 결과 약 $0.23\;cm^2/Vs$의 정공 이동도와 약 $0.4{\times}10^4$의 평균 전류점멸비를 나타내었다.

• Textile Coloration and Finishing
• /
• v.33 no.3
• /
• pp.147-152
• /
• 2021

Bulk polymerization was used to produce poly(vinyl acetate) with different molecular weights, which were then saponified to prepare poly(vinyl alcohol) (PVA) with different molecular weights. With P_n of 2,060 and 3,240, the optimum film formation concentrations of PVA were found 7.5wt.% and 6.5wt.%, respectively. The drawing characteristics of the PVA film prepared at the optimum film formation concentrations were experimented, as well as the thermal characteristics of the PVA film based on the drawing ratio were observed. When the drawing velocity was fixed, it was found that the drawing ratios of all samples decreased as the heat band gap increased, and the melting temperature of the PVA film slightly increased as the drawing ratio increased regardless of the P_n of PVA.

• Journal of Korean Ophthalmic Optics Society
• /
• v.17 no.1
• /
• pp.1-10
• /
• 2012

Purpose: Cellulose acetate (CA) was blended with polyethyleneglycol (PEG) having different molecular weight at various mixing conditions to enhance melt-processibility of CA, which might prevent the harmful effect resulted from the introduction of phthalic plasticizer. Methods: To establish optimal plasticizing conditions, CA/PEG blends were examined under various plasticizing conditions: PEG concentration, molecular weight of PEG, and plasticzing temperature. Mechanical properties of the CA/PEG blends, as well as migration and exudation of the PEG, were performed in order to evaluate the efficiency of plasticization. Results: Compared to industrial CA resin plasticized by diethyl phthalate, CA/PEG blends exhibited similar thermal plasticization. It was established that the optimum condition was to blend 30~40 phr PEG with molecular weight 400 at $175{\sim}180^{\circ}C$. CA/PEG blend showed superior glassness, PEG stability, and mechanical properties. Conclusions: CA/PEG blends would be a eco-friendly glasses frame to substitute traditional CA glasses frame prepared phthalate plasticizers.

• Journal of the Korean Chemical Society
• /
• v.38 no.6
• /
• pp.427-434
• /
• 1994

The retention behaviors of poly(ethylene-co-vinyl acetate)s have been studied by thermal field-flow fractionation(ThFFF) with respect to effective separation and characterization of thermal diffusion coefficients($D_{\tau}$) as one of the physicochemical properties of polymers. The eight copolymers are different in vinyl acetate composition ranging from 25% to 70% and in molecular weight ranging from 110,000 to 285,000. The carrier solvents are THF, toluene and chlorobenzene which have different viscosities and thermal conductivities. It is shown that the retention of a copolymer is dependent on the type of the carrier, the molecular weight and chemical composition of the copolymer. The results show that the retention of a copolymer increases when either vinyl acetate composition or the molecular weight increase. $D_{\tau}$ values measured by experiments vary from 1.36∼5.97 $\cm^2/(s.K)$ depending on the copolymer composition and the type of the carrier solvent. These values increase $(r^2{\geq}0.928)$ with increase of weight % of vinyl acetate. THF is found to be the proper carrier solvent for separation of copolymers employed in this study due to the fact that a $D_{\tau}$ value greatly changes with variation of copolymer composition. From the above results, ThFFF can be used for separation of copolymers with similar molecular sizes but different compositions.

• Korean Chemical Engineering Research
• /
• v.54 no.4
• /
• pp.437-442
• /
• 2016

A new route for PBT (Poly butylene terephthalate) production from recycled PET (Poly ethylene terephthalate) has been explored. The route consists of glycolysis of PET (Poly ethylene terephthalate) wastes using 1,4-butandiol into BHBT oligomers and polycondensation of the oligomers into PBT oligomer. This process uses post-consumer or post-industrial recycled PET and converts it into high-end PBT type engineering thermoplastic via a chemical recycling process. Zink acetate was used as a catalyst for both glycolysis and polycondensation. Two types of reactor for the glycolysis, batch and semi-batch reactor, were investigated and their performances were compared. Semi-batch reactor removes ethylene glycol (EG) and THF (tetrahydrofuran) during the reaction. Amounts of EG and THF generated during the glycolysis reaction were measured and used as criteria for the reactor performance. Performance of semi-batch reactor was shown to be better than that of batch reactor. Optimum reaction condition for the semi-batch reactor was BD/PET ratio of 4, and reaction temperature of $220^{\circ}C$, giving high EG yield (max 91%) and low production of THF. In addition, it was confirmed that the molecular weight of PBT oligomer increases in accordance with the progress of the polycondensation reaction.

• Applied Biological Chemistry
• /
• v.11
• /
• pp.67-76
• /
• 1969

The reduced pressure storage of apple, American Summer Pairman, was investigated comparing with the other storage methods and the following results were obtained. 1. The reduced pressure storage was better to extend the storage life and freshness of apples than the controlled atomoshere storage. 2. Decreasing the pressure of chamber atmosphere to about 20 cmHg showed the best result among several pressure conditions. 3. As for the surface treatment of the apples, poly-ethylene film wrapping showed to be the most favorable method in a short-term experiment. In a long-term experiment, however, poly-ethylene film wrapping seemed to cause apples rot. Poly-vinyl acetate coating seemed to keep the apples from color changing, but it caused an unpleasant odor and a peculiar taste. No significant effect was observed in Gibberellin. 4. Total sugar and reduced sugar of apples were decreased after a certain period of increasing. Acid and Vitamin C, however, gradually decreased from the beginning of storage.

• Journal of the Korea Furniture Society
• /
• v.16 no.1
• /
• pp.1-8
• /
• 2005

This experiment was carried out to investigate the gluing characteristics of poly vinyl acetate emulsion adhesive(PVAc) on the Cryptomeria japonica laminated boards. This sample trees are major planting species and have been planted in southern district for a long time. The optimum gluing conditions for laminated board were summarized as follows; the amount of spreading glue, assembly time, clamping pressure, and clamping time for PVAc resin were $200g/m^2$, 10min., $5kg/cm^2$, and 6hrs., respectively, and the relative formulae between extension ratio(x) and block shear strength(y) was $y=-9.6x+85.2(R^2=0.95)$.

• Journal of the Korea Furniture Society
• /
• v.17 no.2
• /
• pp.25-34
• /
• 2006

This experiment was carried out to investigate the high-frequency gluing characteristics of poly vinyl acetate emulsion adhesive(PVAc) on MDF edge-glued boards. The edge-glued boards were glued lengthwise with butt, scarf, or finger joint. The wastes of MDF boards were reused as board materials. The obtained results are summarized as follows; the bending strength of edge-glued MDF increased slightly with the HF heating time, but the economically desirable heating time was 6 minutes. The bending and tensile strength of edge-glued MDF were high with scarf, finger and butt joint, in order. The strength of finger jointed MDF showed 80% of scarf jointed MDF. The effects of location of finger joints on the bending strength of edge-glued MDF were larger than those of the numbers of finger joints. The bending strength of edge-glued MDF with one joint on the middle position showed 40% decrease in comparison with non-jointed MDF.