• 한국자동차공학회논문집
• /
• 제14권2호
• /
• pp.57-66
• /
• 2006

AA5182-polypropylene sandwich sheet was manufactured, and the mechanical properties evaluation was executed in order to identify $L{\ddot{u}}ders$ band that causes fabrication process problem and especially surface roughness. To identify formability, deformation behavior, plastic strain ratio (R-value) and pole figure were measured, and texture analysis was performed. In the case of sandwich sheet, the unstable deformation behavior has decreased. As well, for sandwich sheet, A1 skin could manage the most of load, and the elongation has improved about 45% more than that of A1 skin. The plastic strain ratio of A1 skin and sandwich panel, which indicates serration behavior, was obtained from instantaneous plastic strain ratio evaluation. Also, the planar anisotropy of sandwich sheet has decreased more than that of A1 skin. According to these results, the sandwich sheet produced lightening effect and could control unstable deformation characteristic, that is, surface roughness caused by $L{\ddot{u}}ders$ band. Furthermore, it was proved that the texture control of the rolling attachment of A1 skin is necessary to improve the formability of the sandwich panel.

• Progress in Superconductivity
• /
• 제3권1호
• /
• pp.95-98
• /
• 2001

Recently, NiO films have been studied as a buffer layer to fabricate the superconductor with preferred orientation and as a diffusion barrier to prevent the reaction between superconductor and textured nickel substrate . We fabricated NiO films on textured Ni substrate by thermal oxidation with various variables of temperature, oxidation time, atmosphere, and cooling rate. We investigated the alignment of NiO films by XRD and pole figure and the microstructures by SEM. (200) <001> alignment of NiO film was observed at the oxidation condition of $1200^{\circ}C$ far 10min and slow cooling in O2 atmosphere. During the process in Ar atmosphere, we could also observe the thermal faceting which affects the alignment of NiO alms on Ni substrate.

• 한국초전도ㆍ저온공학회논문지
• /
• 제4권2호
• /
• pp.5-10
• /
• 2002

Deposition condition of NiO that is one of Possible buffer layers for YBCO coated conductors was studied. NiO was deposited on textured Ni substrates by a MOCVD (metal-organic chemical vapor deposition) method. The degree of texture, and the surface roughness were analyzed by X-ray Pole figure, atomic force microscope and scanning electron microscope. The (111) and (200) textures were competitively developed , depending on an oxygen partial Pressure(PO2) and deposition temperature (Tp). The (200) textured NiO layer was deposited at Tp=450~47$0^{\circ}C$ and PO2= 1.67 Torr Out-of-Plane ($\omega$-scan) and in-plane ($\Phi$-scan) textures of the (200) NiO films were as good as 10.34$^{\circ}$ and 10.00$^{\circ}$ respectively The AFM surface roughness of NiO was in the range of 3~4.5 nm at PO2=0.91~3.34 Torr and at Tp=47$0^{\circ}C$ , and in the range of 3~13 nm at TP=450~53$0^{\circ}C$ and at PO2=1.67 Torr.

• 한국전자파학회논문지
• /
• 제10권5호
• /
• pp.672-679
• /
• 1999

능동 여파기는 고집적화를 통한 소형화 추세에 있는 고주파 회로 block에 있어서 가장 핵심적인 부분중의 하나로 많은 연구가 진행되고 있으며 다수의 논문들이 발표되어 왔다. 본 논문에서는 공진기와 공진기를 연 결하고 있는 인버터를 능동소자로 대체하여 여파기를 설계하는 방법을 제시하였다. 기존의 논문에서도 본 방 법으로 연구된 사례가 있지만, 능동소자 및 능동회로로 구성된 인버터의 성능을 이론적으로 분석하지 않고 증폭기 block으로 사용하였기 때문에 여파기 성능에 미치는 영향을 고려하지 않았다. 본 논문에서는 능동소자가 갖는 특성을 해석하여 기존의 고주파 여파기 회로 설계방식에 그대로 이용할 수 있는 방법을 제시하였다. 설계된 3단 능동 여파기의 특성은 중심 주파수 865 MHz, 대역폭 75 MHz, 삽입 이득 24 MHz, 잡음지수는 2.5 d dB이하를 보였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 초전도 자성체
• /
• pp.59-63
• /
• 2002

The purpose of this paper is to investigate the crystal texture of the 2223 phase and its relationship with PIT processing parameter. Ag-sheathed Bi-2223 multi-filament tapes were prepared by changing rolling reduction ratio. We analysed the degree of texture for 2223 phase after heat-treatment. According to X-ray pole-figure, the texture of the filaments located near surface and center were not so different each other for all rolling conditions. we found a little higher degree of texture for 60% rolling reduction. But its difference is not so high compared with those tapes with a lower rolling reduction ratio. Reaction induced texturing seemed to contribute with a large portion under present condition.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1247-1248
• /
• 2006

We fabricated YBCO film using a TFA-MOD method. In order to enhance the reaction kinetics and to control the formation of the second phases, $Y_2Ba_1Cu_1O_x$ and $Ba_3Cu_5O_8$ powders were used as precursors (the so called "211 process"). The films were calcined at $460^{\circ}C$ and then fired at $750^{\circ}C-800^{\circ}C$ in a 12.1% humidified $Ar-O_2$ atmosphere. We found that the microstructure varied significantly with the firing temperature. The textures of all of the films were similar and mainly biaxial. For the film fired at $775^{\circ}C$, the critical current was obtained to be 39 A/cm-width (corresponding critical current density is 2.0 MA/$cm^2$).

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 추계학술대회 논문집
• /
• pp.55-58
• /
• 2003

We fabricated the textured Ni substrate and evaluated the effects of processing variables on microstructural evolution and texture transformation. Ni-rods as an initial specimen were prepared by two different methods, i.e., powder metallurgy(P/M) and plasma arc melting(PAM) The texture of the substrate was characterized by pole-figure and surface condition was evaluated by atomic force microscopy. It was observed that the texture of substrate made by P/M did not significantly varied with annealing temperature of 800~120$0^{\circ}C$ and the full-width at half-maximums (FWHM) of both in-plane and out-of-plane were 9$^{\circ}$~10$^{\circ}$. On the other hand, the texture of substrate made by PAM was more dependent on the annealing temperature and the FWHMs of in-plane texture was 9$^{\circ}$~13$^{\circ}$ at the temperature range. In addition, twin texture, (221)＜221＞, was formed as the temperature increased further. The grain size of substrate made by P/M was smaller than that made by PAM and this difference was correlated to the microstructure of initial specimens.

• 한국분말재료학회지
• /
• 제10권4호
• /
• pp.241-248
• /
• 2003

Biaxially textured Ni tapes were fabricated by a cold working and recrystallization heat treatment processes from powder compact rods. The processing parameters associated with the cube texture formation in Ni tapes were systematically investigated by using X-ray diffraction and pole-figure analysis. The Ni powder used in this study was 5 $\mu$m in size and 99.99% in purity. To find the optimum sintering temperature, tensile tests were performed for Ni rods sintered at various temperatures. The Ni rods sintered at 100$0^{\circ}C$ showed poor elongation and low fracture strength, while the Wi rods sintered above 100$0^{\circ}C$ revealed good mechanical properties. The higher elongation and fracture strength of the Ni rods sintered at higher temperatures than 100$0^{\circ}C$ are attributed to the full densification of the sintered rods. The sintered Ni rods were cold-rolled with 5% reduction to the final thickness of 100 $\mu$m and then annealed for development of rube texture in rolled Ni tapes. The annealed Ni tapes depicted strong cube texture with FWHM(full-width at half-maximum) of in-plane and out-of-plane in the range of 8$^{\circ}$ to 10$^{\circ}$. The NiO deposited on the Ni tapes by MOCVD process showed good epitaxy with FWHM=10$^{\circ}$, which indicates that the Ni tapes can be used as a substrate for YBCO coated conductors.

• Applied Microscopy
• /
• 제45권3호
• /
• pp.170-176
• /
• 2015

In this work, various electron microscopy and analysis techniques were used to investigate the microstructural evolution of a 9% Cr tempered martensite ferritic (TMF) steel T91 upon ultrasonic nanocrystalline surface modification (UNSM) treatment. The micro-dimpled surface was analyzed by scanning electron microscopy. The characteristics of plastic deformation and gradient microstructure of the UNSM treated specimens were clearly revealed by crystal orientation mapping of electron backscatter diffraction (EBSD), with flexible use of the inverse pole figure, image quality, and grain boundary misorientation images. Transmission electron microscope (TEM) observation of the specimens at different depths showed the formation of dislocations, dense dislocation walls, subgrains, and grains in the lower, middle, upper, and top layers of the treated specimens. Refinement of the $M_{23}C_6$ precipitates was also observed, the size and the number density of which were found to decrease as depth from the top surface decreased. The complex microstructure and microstructural evolution of the TMF steel samples upon the UNSM treatment were well-characterized by combined use of EBSD and TEM techniques.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2000년도 제18회 학술발표회 논문개요집
• /
• pp.122-122
• /
• 2000

Magnesium oxide is thermodynamically very stable, has a low dielectric constant and a low refractive index, and has been widely used as substrate for growing various thin film materials, particulary oxides of the perovskite structure. There has been a considerable interest in integrating the physical properties of these oxides with semiconductor materials such as GaAs and Si. In this regard, it is considered very important to be able to grow MgO buffer layers epitaxially on the semiconductors. Various oxide films can then be grown on such buffer layers eliminating the need for using MgO single crystal substrates. Vapor phase epitaxy of magnesium oxide has been accomplished on Si(001) substrates in a high vacuum chamber using the single precursor methylmagnesium tert-butoxide in the temperature range 750-80$0^{\circ}C$. For the epitaxy of the MgO films, SiC buffer layers had to be grown on Si(001). The films were characterized by reflection high energy electron diffraction (RHEED) in situ in the growth chamber, and x-ray diffraction (XRD), x-ray pole figure analysis, scanning electron microscopy (SEM), and x-ray photoelectron spectroscopy (XPS) after the growth.