• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.337-340
• /
• 2001

The suction muffler of a reciprocating compressor is used for reducing noise produced by pressure pulsations. According to the shape, the suction muffler is classified into one-chamber type, two-chamber type, Helmholtz resonator type, pipe-resonator type, and so on. These mufflers are used according to the characteristics of the frequency of compressor noise. In this study, four pole parameters have been used for calculating Transmission Loss of the muffler, and Insertion Loss has been acquired for the optimum design of the muffler by the experiment.

• Proceedings of the KIEE Conference
• /
• 2008.10c
• /
• pp.41-43
• /
• 2008

This paper deals with a study on characteristic of inductance on spoke type motor. The rotor and stator is redesigned as rounding teeth of stator and pole surface of rotor. Result, a shape of air-gap is changed and the cogging torque is reduced greatly. In consequence, the inductance of spoke type motor is changed. The Finite Element Analysis(FEM) is used to characteristics.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.7
• /
• pp.320-326
• /
• 2003

Slotless Permanent Magnet Linear Synchronous Motor (PMLSM) has good control ability but thrust density is low. So, this paper proposes inserted core type of slotless PMLSM to improve its thrust density. Inserting the core between windings of each phase, detent force is generated by the difference of magnetic resistance in an air gap. To minimize detent force, this paper applies the neural network to inserted core type of slotless PMLSM. The, Magnetic pole ratio, the width of the inserted core and the width of the coil are selected as a design parameter to minimize detent force. In comparison with inserted core type one, thrust ripple greatly decreases by minimizing detent force and also thrust increases in this optimal model.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.3
• /
• pp.342-348
• /
• 2012

This paper presents a moving-magnet type linear actuator designed by using flux concentration type permanent magnet arrangement, which can generate higher magnetic flux density in air-gap. In this construction, detent force which is induced by both slot-effect and end-effect becomes larger due to strong attractive forces. To reduce cogging force we have employed a modular mover structure of two magnetic pole sections connected with a center yoke. The improved motor performance is demonstrated with the prototype machine.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.4
• /
• pp.739-745
• /
• 2011

This paper proposes a method for reducing the negative spatial harmonics of the radial flux density of an interior-type permanent magnet (IPM) motor. The reliability of the motor is increased by minimizing its vibrations under dynamic eccentricity (DE) state and normal state due to reduction of a negative spatial harmonics component through the influx of a zero spatial harmonics component in the radial flux density. To minimize the vibrations, optimal notches corresponding to the distribution shape of the magnetic field are designed on the rotor pole face. The variations of vibration computation by finite element method (FEM) and the validity of the analysis and rotor shape design are confirmed by vibration and performance experiments.

• Journal of the Korean Magnetics Society
• /
• v.26 no.2
• /
• pp.55-61
• /
• 2016

This study proposes the design algorithm of an electromagnetic linear actuator with a divided coil excitation system, such as the colenoid (COL) system, using the equivalent magnetic circuit (EMC) method. Nowadays, the clamping device is used to hold workpiece in the electrically driven chucking system and is needed to produce a huge clamping force of 40 kN like hydraulic system. The design algorithm for electromagnetic linear actuator can be obtained using the EMC method. At first, the parameter map is used to decide the slot width ratio in the initial design. Next, to make the magnetic flux density uniform at each pole, the pole width is adjusted by the pole width adjusting algorithm with EMC. When the dimensions of the electromagnetic linear actuator are decided, the clamping force is calculated to check the desired clamping force. The design results show that it can be used to hold a workpiece firmly instead of using a hydraulic cylinder in a chucking system.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.159-162
• /
• 2002

The eleventh-order coupled line lowpass filter(LPF) was designed to suppress harmonics and spurious signals. The microstrip type LPF was fabricated using a high-$T_{c}$ superconductor(HTS) $YBa_{2}$$Cu_{3}$$O_{7-x}$(YBCO) thin film with the $CeO_{2}$ buffer layer which was deposited on the sapphire ($Al_{2}O_{3}$) substrate of 30 x 30 $mm^{2}$. The coupled-line type LPF was designed for 1.2 GHz of cutoff frequency with 0.01 dB of ripple level at passband. The fabricated HTS LPF shows excellent attenuation characteristics in stopband of 1.2~9.5GHz (7-attenuation poles in the stopband), and shows low insertion loss (0.2 dB) and return loss (17.1 dB) in the pass- band. These measured results match well with those obtained by the EM simulation. This clearly demonstrates that the HTS LPF can suppress harmonics and spurious signals effectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.4
• /
• pp.99-106
• /
• 2005

In this study, the electromagnetic characteristics of a flat-type two-dimensional proportional solenoid were analyzed by the magnetic reluctance method. The equivalent magnetic circuit equation for the solenoid was derived by modeling the reluctance of air gaps and magnetic structural components such as pole core, armature and yoke. It was solved iteratively because of the nonlinear magnetization properties of the iron parts. The solutions showed good agreement with experimental data. Based on the equivalent magnetic circuit equation, the influence of design parameters on the force-to-armature displacement curves was mathematically derived and experimentally verified. In this way, dominant design parameters could be analytically determined.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.1
• /
• pp.7-15
• /
• 2002

The paper proposes the characteristics analysis for a Transverse flux type Switched Reluctance Motor(TSRM) considering the nonlinear magnetic phenomena. To investigate the nonlinear parameters of magnetic equivalent circuit, the designed TSRM is analyzed by the 2D and 3D finite element method as functions of input current and angular displacement. On the base of FEM analysis results, the current, torque, back EMF and output power wave of TSRM are simulated from the motion equation by MATLAB/Simulink. The simulated performance characteristics for a 4-phase, 24-pole TSRM are verified by experimental results of a prototype TSRM.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1998.06a
• /
• pp.331-336
• /
• 1998

A systematic design method for PDC(Parallel Distributed Compensation)-type continuous time Takagi-Sugeno(T-S in short) fuzzy control systems which have inaccessible states is developed in this paper. Reduced-dimensional fuzzy state estimator is introduced from existing T-S fuzzy model using the PDC structure of Wang et al. [1] LMI(Linear Matrix Inequalities) problems which represent the stabililty of the reduced-dimensional fuzzy state estimator are derived. Pole placement constraints idea for each rules is adopted to determine the estimator gains and they are also revealed as LMI problems. these LMI problems are combined with Joh et al's [7][8] LMI problems for PDC -type continuous time T-S fuzzy controller design to yield a systematic design method for PDC -type continuous time T-S fuzzy control systems which have inaccessible states.