• 한국측량학회지
• /
• 제40권1호
• /
• pp.1-14
• /
• 2022

굴착 현장에서 신속·정확·안전한 측량을 위해 본 연구에서는 드론을 이용한 지하 시설물 측량의 적용 가능성 및 3D 시각화의 기대효과를 다음과 같이 도출하였다. Phantom4 Pro 20MP의 드론으로 30m의 비행 고도, 중복도 85%의 비행계획으로 0.85mm의 GSD (Ground Sampling Distance)값을 확보하였고, GCP (Groud Control Point)4점과 검사점 2점을 계산하여 기준점에 대하여 7.3mm, 검사점은 11mm의 성과를 취득할 수 있었다. 저가의 드론으로 측량할 경우 GCP의 중요성이 확인되었으며, 지상 기준점이 없는 경우, X값의 오차 범위는 -81.2cm에서 +90.0cm, Y값의 오차 범위는 +6.8cm에서 155.9 cm 값을 도출하였다. Pix4D 프로그램을 이용하여 포인트 클라우드 데이터를 분류하였다. 지하 시설물 데이터와 도로 포장면의 데이터를 분류하고, 중첩과정을 통해 실제 모형의 도로와 지하 시설물의 데이터를 3D 시각화하였다. 중첩된 포인트 클라우드 데이터는 Open Source 프로그램인 CloudCompare를 통해 사용자가 원하는 장소의 위치와 심도 정보를 확인할 수 있게 되었다. 본 연구결과로 지하 시설물 측량의 새로운 패러다임으로 자리매김하게 될 것이다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.2108-2111
• /
• 2005

The mission life of a satellite determines the amount of fuel required on-board, while the total mass requirement limits the fuel to be loaded. Hence, for the design of thruster control loop, not only the satellite pointing accuracy but the saving of fuel is to be considered. In this paper, a two-step fuzzy controller is proposed for the thruster control loop to save fuel consumption. This approach combines requirements for pointing control accuracy with minimum fuel consumption into a fuzzy controller design. To demonstrate this approach, we have designed a fuzzy controller for the Sun point Mode of KOMPSAT-2. The performance of this fuzzy controller design is compared with that of PD controller used for KOMPSAT-2.

• 한국음향학회지
• /
• 제23권4호
• /
• pp.323-332
• /
• 2004

음상정위를 제어하는 한 방법으로 음원으로부터 모의하고자 하는 두 귀까지의 머리전달함수 (HRTF)를 모의하는 방법이 유효하다. 그러나, 이 방법을 이용한 경우, 모의계를 설계할 때의 수음점과 청취시의 수음점이 완전하게 일치하는 경우에는 정밀한 모의가 가능하나, 청취시에 머리가 이동한 경우에는 모의정도가 크게 저하하는 문제점이 있다. 이러한 문제점을 해결하기 위해, 본 논문에서는 외이도의 입구뿐만 아니라 그 근방의 복수개의 점의 음압을 제어하는 것에 의해 머리가 다소 이동하더라도 제어가 가능하도록 한 모의계의 구성 방법을 제안한다. 본 논문에서는 이 방법을 이용해 머리전달함수를 모의한 경우에 대하여 물리적인 모의정도와 청감상의 음상정위의 정확도에 대하여 종래의 방법과 비교하여 실험했다. 그 결과 복수개의 점에 있어서의 온압을 제어하는 것에 의해 청취위치가 6 cm 정도까지 이동한 경우에도 수평면상에서 방향의 지각 오차를 종래의 방법보다 적게 할 수 있다는 것을 인간을 대상으로 한 청취실험을 통해 증명했다.

• Journal of Power Electronics
• /
• 제6권3호
• /
• pp.226-234
• /
• 2006

Photovoltaic (PV) generators have nonlinear V-I characteristics and maximum power points which vary with illumination level and temperature. Using a maximum power point tracker (MPPT) with an intermediate converter can increase the system efficiency by matching the PV systems to the load. This paper presents a maximum power point tracker based on fuzzy logic and a control scheme for a single-phase inverter connected to the utility grid. The fuzzy logic controller (FLC) provides an adaptive nature for system performance. Also the FLC provides excellent features such as fast response, good performance and the ability to change the fuzzy parameters to improve the control system. A single-phase AC-DC inverter is used to connect the PV system to the grid utility and local loads. While a control scheme is implemented to inject the PV output power to the utility grid at unity power factor and reduced harmonic level. The simulation results have shown the effectiveness of the proposed scheme.

• 제어로봇시스템학회논문지
• /
• 제14권2호
• /
• pp.161-167
• /
• 2008

This article describes the methods of a decision of the location which user points to move by an optical device like a laser pointer and a moving to that location. Using a conic mirror and CCD camera sensor, a robot observes a spot of user wanted point among an initiative, computes the location and azimuth and moves to that position. This system offers the brief data to a processor with simple devices. In these reason, we can reduce the time of a calculation to process of images and find the target by user point for carrying a robot. User points a laser spot on a point to be moved so that this sensor system in the robot, detecting the laser spot point with a conic mirror, laid on the robot, showing a camera. The camera is attached on the robot upper body and fixed parallel to the ground and the conic mirror.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1004-1007
• /
• 1996

Various auto-tuning methods using relay feedback are presented recently. They are composed of the consecutive procedures identifying Nyquist critical point using relay feedback and designing PID controller by one point of Nyquist plot mapping. This paper suggests a strategy to get the knowledges of Nyquist critical point and the neighborhood point of it using relay feedback. The parameters of PID controller are established by dominant pole approximation based on these knowledges. Designers can make use of the damping ratio as a time domain specification. So design flexibilities are taken in view of stability and performance of the system response considering practical system condition.

• Journal of Power Electronics
• /
• 제17권1호
• /
• pp.1-10
• /
• 2017

This paper presents a novel predictive digital control method for boundary conduction mode PFC converters without the need for detecting the inductor current. In the proposed method, the inductor current is predicted by analytical equations instead of being detected by a sensing-resistor. The predicted zero-crossing point of the inductor current is determined by the values of the input voltage, output voltage and predicted inductor current. Importantly, the prediction of zero-crossing point is achieved in just a single switching cycle. Therefore, the errors in predictive calculation caused by parameter variations can be compensated. The prediction of the zero-crossing point with the proposed method has been shown to have good accuracy. The proposed method also shows high stability towards variations in both the inductance and output power. Experimental results demonstrate the effectiveness of the proposed predictive digital control method for PFC converters.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.84-86
• /
• 2001

A new navigation method is developed and implemented for mobile robot. The mobile robot navigation problem has traditionally been decomposed into the path planning and path following. Unlike tracking-based system, which minimize intercept time and moved mobile robot distance for optimal rendezvous point selection. To research of random moving object uses algorithm of Adaptive Control using Auto-regressive Model. A fine motion tracking object's trajectory is predicted of Auto-regressive Algorithm. Thus, the mobile robot can travel faster than the target wi thin the robot's workspace. The can select optimal rendezvous point of various intercept time.

• Journal of Biosystems Engineering
• /
• 제32권5호
• /
• pp.284-291
• /
• 2007

This study was to investigate performance of position, basic controls and additional control for man-machine interface on a 3-point hitch of a tractor. The developed additional control was one-touchup, backup, turnup, liftarm limited, PTO on/off and an external control. As a result of experiment, maximum steady state error of response system was lower than $0.8^{\circ}$ and this result showed the function operated normally because the dead band of system set was ${\pm}1^{\circ}$. There was no abnormal situation by switch operation and sensor signal during the performance test. The results of experiment showed the characteristics of the response was sufficient to be used as the position and additional control system for tractors.

• 대한전자공학회논문지
• /
• 제25권12호
• /
• pp.1601-1609
• /
• 1988

In the control of the robotic manipulators, the variable structure control method for the set point Regualation has an advantage of the insensitivity about parameter variations and disturbances. When the robotic manipulatores are controlled by a point-to-point scheme, no path constraint is considered. Thus, the variable structure control method will be effectively applied only if the trajectory of the robot hand is estimated precisely. In this paper, the joint trajectories in the joint space and the hand trajectory in the cartesian space are calculated by the variable structure control method, and an algorithm is suggested to elaborate the deviation error of the robot hand from a straight line path. The result of this study will become a base of the effective path planning about robotic manipulators with the variable structure control concept.