• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.6 no.2
• /
• pp.34-41
• /
• 1988

Nowadays the considerable improvements, not only in photogrammetric equipment but also in adjustment methods have led to a high accuracy of Aerial Triangulation and reach the step to obtain A.T. technique that uses Global Position System without ground control survery. The enterance of analytical plotter have made considerable development both in accuracy and in efficiency and improved working environment of A.T. by the combination of On-Line Analytical Plotting System. In this paper, in A.T., with using of analytical polotter, aims to improve the acccuracy in coordinates determination of low level control point. The result shows that in case of A.T. with analytical plotter AVIOLYT BC2, the accuracy of control points improves to 7% in planimetry and to 40% in height compared to A.T. with precision plotter Autograph A-8.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1742-1745
• /
• 1997

We have developed a highly responsible probing system for inspection of electrical properties of assemble PCB$_{s}$ (printed circuit boards). However, as the duration of the impact occurring between a probe and a solder joint on PCB is very short, it is very difficult to control the harmful peak impact force and the slip motion of the probe to sufficient level only by its vorce feedback control with high gains. To overcome these disadvantages of the prototype, it needs ot obtain some information of the solder joint in advance before the contact. In addition, to guarantee the reliability of the probing task, the probing system is required to measure several points around the probale target point at high speed. There fore, to meet such requirements, we propose a new noncontaet sensor capable of detecting simultaneously position and normal vectors of the multiple points around the probable target point in real time. By using this information, we can prepare a control strategy for stable contact motion on impact. In this paper, we described measuring priniciple, design, and development of the sensor. The effectiveness of the proposed sensor is verified through a series of experiments.s.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.4
• /
• pp.99-104
• /
• 2010

We introduce Internet TCP/IP control system to monitor the traffic volume on the traffic network system. To check the traffic volume on traffic road, we use the traffic detector system shppe of circle or diamond or rectangular. Nevertheless we use traffic detector, we will use internet addressin TCP/IP system. If we use TCP/IP control system, we acquire many good point, we achive high sircurity and low costness traffic monitoring system coming difficulty and high level position. But internet system is very easy and low cost direction. Traffic control system is very more depending on the high techinquesion and very complexity. Therefore we introducing TCP/IP internet addressing control system schemetic point.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.3
• /
• pp.199-206
• /
• 2017

Maximum Power Point Tracking (MPPT) control needs to generate the maximum power of a tidal current turbine. A tidal current speed sensor is required to achieve effective generated power in a tidal current generation system. The most common methods used to achieve such power is the tip speed ratio of turbine and tidal current information. However, these methods have disadvantages, such as expensive installation of the tidal current sensor, parameter errors in turbine design, and different information according to the installed position of the tidal current sensor. This paper proposes a maximum power control scheme using perturb-and-observe (P&O) for tidal current generation system. The proposed P&O MPPT scheme can achieve the maximum power without tidal current sensors and turbine design parameters. The reliability and suitability of the proposed control scheme are proven through simulation and experiment results at the tidal current generation laboratory.

• Journal of fish pathology
• /
• v.26 no.2
• /
• pp.59-64
• /
• 2013

This study aimed to develop an algorithm to determine the optimal injection position in olive flounder, Paralichthys olivaceus when a vaccine is injected into the fish by using a vision-based automatic equipment measruing the total length (TL), width and weight of the fish. Over a 5-month period, 500 olive flounders were examined to analyze the relation of the fish size and to the shape and location of its abdomen, using radiography, a ruler plate and scale. There were significant correlations between the TL and the shape and location of the abdomen. The abdomen was located 0.232TL - 2.7221 mm ($R^2$=0.8787) from the end of the mouth of the fish. The height and width of the abdomen in the fish were 0.1292TL + 1.8768 mm ($R^2$=0.7935) and 0.183TL-5.9791 mm ($R^2$=0.8641), respectively. The injection point in the abdominal region avoiding organs was determined by calculating the center of gravity of the abdomen volume. This can be expressed as g (0.2759TL - 2.0965, 0.1295TL - 4.2325) on the basis of TL line coordinates. The injection point by the expressed coordinates had errors for the x and y axes as 12.15 mm and 8.28 mm, respectively. These were enough to use the algorithm to injection for the equipment. This automated method to determine the position of any part in the fish can also be used for other purposes, for example, intramuscular injection or auto-tagging of fish.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.2
• /
• pp.164-170
• /
• 2010

In brushless DC motor, current flow should be controlled such that only properly selected 2 out of 3 phases carry current depending on the position of rotor. In order to detect position of rotor, hole sensor, encoder, optical position-detecting sensor, and magnetic position-detecting sensor are frequently employed. These sensors not only often cause malfunction in low and high temperature but they also have disadvantage of increasing cost and size of an motor system. To reduce the cost and size and to increase the robustness of the motor system, recently researches on sensorless motor dirve are very active. This paper proposes a novel unipolar PWM switching method that can improve the control problem caused by the difficulty of detecting zero crossing point at high revolution speed by minimizing the switching noise while increasing the lifespan of the drive system.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.9
• /
• pp.43-54
• /
• 2013

This study proposed a new embankment stability control method to analyze the measurement data on the slope activities of the soft ground, using the Stability Control Index (SCI) obtained from the p-q stress paths. In order to validate this new technique, the data from triaxial compression tests (CU) and field measurement were compared. SCI is calculated from the current path of the effective stress points ($p^{\prime}=p-{\Delta}u$) using the relative position between the Total Stress Path $p_{max}$ and the point of $k_f$ line $p_f$. From this result, the point of effective stress $p^{\prime}(=p-{\Delta}u)$ will have access to the point $p_f$ of $k_f$ line when the pore water pressure occurs or the point of total stress pass $p^{\prime}_{max}$ when the pore pressure dissipates. Thus, the Stability Control Index (SCI) can evaluate quantitatively the safety of embankment from the relative position of the effective stress path.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1396-1401
• /
• 2004

In recent years, robot has been used widely in industrial field and has been expanded as a result of continous research and development for high-speed and miniaturization. The goal of this paper is to design the special serial manipulator through the understanding of the structure, mobility, and analysis of serial manipulator. Thereafter we control the position and orientation of end-effector with respect to time. In general, a structure of industrial robot consists of several links connected in series by various types of joints. Typically revolute and prismatic joints. The movement of these joints is determined in inverse kinematic analysis. Compared to the complicated structure of parallel and hybrid robot, open loop system retains the characteristic that each link is independent and is controlled easily by AC servomotor that is used to place the robot end-effector toward the accurate point with the desired speed and power while it is operated by position control algorithm. The robot end-effector should trace the given trajectory within the appropriate time. The trajectory of 3D end-effector model made by OpenGL can be displayed on the monitor program simultaneously

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2000-2003
• /
• 2003

In recent years, robots have been used widely in industrial field and have been expanded as a result of continuous research and development for high-speed and miniaturization. The goal of this paper is to design the serial manipulator through kinematic analysis and to control the position and orientation of end-effector with respect to time. In general, a structure of industrial robot consists of several links connected in series by various types of joints, typically revolute and prismatic joints. The movement of these joints is determined in inverse kinematic analysis. Compared to the complicated structure of parallel and hybrid robot, open loop system retains the characteristic that each link is independent and is controlled easily. AC servo motor is used to place the robot end-effector toward the accurate point with the desired speed and power while it is operated by position control algorithm. The robot end-effector should trace the given trajectory within the appropriate time. The trajectory of end-effector can be displayed on the monitor of general personal computer through Opengl program.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.6
• /
• pp.497-502
• /
• 2015

One of the goals in the field of mobile robotics is the development of personal service robots for the elderly which behave in populated environments. In this paper, we describe a security robot system and ongoing research results that minimize the risk of the elderly and the infirm to access an area to enter restricted areas with high potential for falls, such as stairs, steps, and wet floors. The proposed robot system surveys a potential falling area with an equipped laser scanner sensor. When it detects walking in elderly or infirm patients who in restricted areas, the robot calculates the velocity vector, plans its own path to forestall the patient in order to prevent them from heading to the restricted area and starts to move along the estimated trajectory. The walking human is assumed to be a point-object and projected onto a scanning plane to form a geometrical constraint equation that provides position data of the human based on the kinematics of the mobile robot. While moving, the robot continues these processes in order to adapt to the changing situation. After arriving at an opposite position to the human's walking direction, the robot advises them to change course. The simulation and experimental results of estimating and tracking of the human in the wrong direction with the mobile robot are presented.