• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.357-362
• /
• 2008

This study have goal with reverse engineering for petrochemistry of high pressure ball valve for localization. Ball valve for development accomplished with flow analysis based on provision of ANSI B16.34, ANSI B16.10, ANSI B16.25 In order to localize the petrochemistry high pressure control valve. Numerical simulation using CFD(Computational Fluid Dynamic) in order to predict a mass flow rate and a flow coefficient form flow dynamic point of view. The working fluid assumed the water($H_2O$). The valve inlet and outlet setup a pressure boundary condition. The outlet pressure was fixed by atmospheric pressure and calculated inlet velocity 5m/s. CFD solver used STAR-CCM+ which is commercial code. The result shows change of mass flow rate according to opening and closing angle of valve. Flow decrease observed open valve that equal percentage flow paten which is general inclination of ball valve. The structural analysis used ANSYS which is a commercial code. Stress analysis result of internal pressure in valve showed lower than yield strength. This is expect to need more detail design and verification for stem and seat structure.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1195-1200
• /
• 2008

This study have goal with conceptual design for Offshore Structures of high pressure control valve for localization. Ball valve for development accomplished with flow analysis based on provision of ANSI B16.34, ANSI B16.10, ANSI B16.25 In order to localize the Offshore Structures high pressure control valve. Numerical simulation using CFD(Computational Fluid Dynamic) in order to predict a mass flow rate and a flow coefficient form flow dynamic point of view. The working fluid assumed the glycerin($C_3H_8O_3$). The valve inlet and outlet setup a pressure boundary condition. The outlet pressure was fixed by atmospheric pressure and calculated until increasing 1bar to 10bar. CFD analysis used STAR-CCM+ which is commercial code and Governing equations were calculated by moving mesh which is rotated 90 degrees when ball valve operated opening and closing in 1 degree interval. The result shows change of mass flow rate according to opening and closing angle of valve. Flow decrease observed open valve that equal percentage flow paten which is general inclination of ball valve. Relation with flow and flow coefficient can not be proportional according to inlet pressure when compare with mass flow rate. Because flow coefficient have influence in flow and pressure difference. Namely, flow can be change even if it has same Cv value. The structural analysis used ANSYS which is a commercial code. Stress analysis result of internal pressure in valve showed lower than yield strength. This is expect to need more detail design and verification for stem and seat structure.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.822-823
• /
• 2014

The usual method of generating an image for a multiview display system requires acquiring a color image and depth information of a reference camera. Then, intermediate images, generated using DIBR method, will be captured at a number of different viewpoints and composed to construct an multiview image. When such intermediate views are generated, several holes would be shown because some hidden parts are shown when the screenshot is taken at different angle. Previous research tried to solve this problem by creating a new hole-filling algorithm or enhancing the depth information. This paper describes a new method of enhancing the intermediate view images by applying the Ball Pivoting algorithm, which constructs meshes from a point cloud. When the new method is applied to the Microsoft's "Ballet" and "Break Dancer" data sets, PSNR comparison shows that about 0.18~1.19 increasement. This paper will explaing the new algorithm and the experiment method and results.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.12
• /
• pp.43-51
• /
• 2014

Organic matter in dredged soil has a lot of engineering problem in ground including a large settlement, crack propagation, low bearing capacity and low friction angle. From an agricultural point of view, however, organic matter contributes greatly soil quality and plant health. This paper investigated the relationship between engineering and germination characteristics of stabilized mixture consisting of different ratios of organic content (0 %, 10 %, 20 %, 30 %) for recycling dredged soil including organic matter. Several series of laboratory tests such as flow test, unconfined compressive test and consolidation test were performed to find out engineering characteristics. pH, percent of germination and growth of plants were also measured to investigate the germination characteristics. The experimental results indicated that, as organic content increased, unconfined compressive stress decreased and compression and swelling indices increased. However, percent of germination and plant growth increases as organic content increases.

• The Journal of the Korea Contents Association
• /
• v.15 no.12
• /
• pp.141-152
• /
• 2015

If we look into genre movie, we can see that almost similar forms are repeated in a movie. Such similar elements are largely divided into three units from a mass of story to a very small camera angle. Those can be explained as Formula, Convention, and Iconography. Among those three, convention means custom and it is a structure or an incident in which one story can be divided into second one. Convention is an incident visualized in individual genre, and a movie director tunes audiences through the incident. The director leads a familiar story but all of a sudden, he transforms the familiar scene to a new story. As a product established from the beginning of movie history, movie convention helps communication between audiences and a director. Audiences familiarize themselves with movie convention through repeated activities of watching movies, and the director utilizes it to provide audiences with familiarity. Director Bong Joon-ho not only tunes audiences through traditional convention but also creates a new art work through transformation of convention. A study is conducted on how he used traditional convention and transformation to get a new idea and to engage in his work through his work .

• Journal of Broadcast Engineering
• /
• v.22 no.6
• /
• pp.713-723
• /
• 2017

Since the panoramic image can overcome the limitation of the viewing angle of the camera and have a wide field of view, it has been studied effectively in the fields of computer vision and stereo camera. In order to generate a panoramic image, stitching images taken by a plurality of general cameras instead of using a wide-angle camera, which is distorted, is widely used because it can reduce image distortion. The image stitching technique creates descriptors of feature points extracted from multiple images, compares the similarities of feature points, and links them together into one image. Each feature point has several hundreds of dimensions of information, and data processing time increases as more images are stitched. In particular, when a panorama is generated on the basis of an image photographed by a plurality of unspecified cameras with respect to an object, the extraction processing time of the overlapping feature points for similar images becomes longer. In this paper, we propose a preprocessing process to efficiently process stitching based on an image obtained from a number of unspecified cameras for one object or environment. In this way, the data processing time can be reduced by pre-grouping images based on camera sensor information and reducing the number of images to be stitched at one time. Later, stitching is done hierarchically to create one large panorama. Through the grouping preprocessing proposed in this paper, we confirmed that the stitching time for a large number of images is greatly reduced by experimental results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.1585-1593
• /
• 2015

3D-structured (embossed) aluminum sheets have been used in the heat insulation purpose for automative exhaust parts because of increasing their surface areas and stiffness reinforcement imposed in making the embossing pattern. However, there are many restrictions in press forming of the embossed sheet compared with the flat sheet (non-embossed one) because of its difference in the mechanical properties and the geometrical 3-dimensional shape. In this paper we investigated the deformation characteristic of embossed aluminum sheet in the incremental sheet forming process which has frequently used in the design verification and the trial manufacturing of sheet products. The single point incremental forming (SPIF) experiments for the rectangular cone forming using the CNC machine with a chemical wood-machined die and a circular tool shape showed that the formability of the embossed sheet are better than that of the flat sheet in view of the maximum angle of cone forming. This comes from the fact that the embossed sheet between the tool and the elastic die wall is plastically compressed and the flatted area contributes to increase the plastic deformation. Also the tool path along the outward movement from the center showed a better formability than that of the inward movement from the edge. However the surface quality for the tool path along the outward movement evaluated from the surface deflection is inferior than that of the tool path along the inward movement.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.38 no.4
• /
• pp.35-44
• /
• 2010

This study will define the features of the viewpoint that best enables the view of Busan Port from Young-Do. Special focus will be on spatial distribution, the type Busan Port sights that can be experienced from Young-Do, the compositional characteristic of a port landscape and visual characteristic. The results are based on 27 selected viewpoints and are as follows. Firstly, the patterns of the spatial distribution of viewpoints are classified as park, public facility and wayside types. It was found that most viewpoints are located along a wayside. Secondly, the types of Busan Port sights that can be experienced from Young-Do are divided into three kinds: surrounding stand-line type, facing the port and the type of penetrating city. The major type was of penetrating city among the three patterns. The reason for this is that the point of view for Busan Port was changed into a prospect over the sea since city and road sections have been expanding due to the urbanization of Young-Do. Thirdly, the compositional characteristics of the port landscape are divided into three styles: panoramic, corridor, and rooftop. The most frequent type is the rooftop style among the three characteristics. This fact indicates that the picture of Busan Port seen from Young-Do loses continuity of view and that housetops inhibit the sense of distance. Lastly, the visual characteristics of the viewpoint were analyzed. The angles of the declination of the viewpoints are concentrated on the horizontally closed parts. Thirteen points lie between $-3^{\circ}$ and $-1^{\circ}$, and twelve points between $-6^{\circ}$ and $-4^{\circ}$. The visual axes of the depression are two points because sight is interrupted by buildings which are built when the city expands. Two viewpoints for experiencing the optimum landscape of depression should be prepared to ensure continuous preservation of the viewpoints. The sight creates a wide prospect, reaching from 0.2km to 6.4km. It is expected that the results of this study can be used for the landscape plans of port cities including the management and preservation of viewpoints.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.4
• /
• pp.528-543
• /
• 2005

Statement of problem: Repeated delivery and removal of abutment cause some changes such as wear, scratch or defect of hexagonal structure. It may increase the value of rotational freedom(RF) between hexagonal structures. Purpose: The purpose of this study was to evaluate surface changes and rotational freedom between the external hexagon of the implant fixture and internal hexagon of abutment after repeated delivery and removal under SEM and toolmaker's microscope. Materials and methods: Implant systems used for this study were 3i and Avana. Seven pail's of implant fixture, abutment and abutment screws for each system were selected and all fixtures were perpendicularly mounted in liquid unsaturated polyesther with dental surveyor. Each one was embedded beneath the platform of fixture. Surfaces of hexagonal structure before repeated closing and opening of abutment were observed using SEM and rotational freedom was measured by using toolmaker's microscope. Each abutment was secured to the implant future by each abutment screw with recommended torque value using a digital torque controller and was repeatedly delivered and removed by 20 times respectively. After experiment, evaluation for the change of hexagonal structures and measurement of rotational freedom were performed. Result : The results were as follows; 1. Wear of contact area between implant fixture and abutment was considerable in both 3i and Avana system. Scratches and defects were frequently observed at the line-angle of hexagonal structures of implant fixture and abutment. 2. In the SEM view of the external hexagon of implant fixture, the point-angle areas at the corner edge of hexagon were severely worn out in both systems. It was more notable in the case of 3i systems than in that of Avana systems. 3. In the SEM view of the internal hexagon of abutment, Gingi-Hue abutment of 3i systems showed severe wear in micro-stop contacts that were machined into the corners to prevent rotation and cemented abutment of Avana systems showed wear in both surface area adjacent to the corner mating with external hexagon of implant fixture. 4 The mean values of rotational freedom between the external hexagon of the implant fixture and internal hexagon of abutment were 0.48$\pm$0.04$^{\circ}$ in pre-tested 3i systems and 1.18$\pm$0.25$^{\circ}$ after test, and 1.80$\pm$0.04$^{\circ}$ in pre-tested Avana systems and 2.61$\pm$0.16$^{\circ}$ after test. 5. Changes of rotational freedom after test shouted statistical)y a significant increase in both 3i and Avana systems(P<0.05, paired t-test). 6. Statistically, there was no significant difference between amount of increase in the rotational freedom of 3i systems and amount of increase in that of Avana ones(P>0.05, unpaired t-test). Conclusion: Conclusively, it was considered that repeated delivery and remove of abutment by 20 times would not have influence on screw joint stability. However, it caused statistically the significant change of rotational freedom in tested systems. Therefore, it is suggested that repeated delivery and remove of abutment should be minimal as possible as it could be and be done carefully Additionally, it is suggested that the means or treatment to prevent the wear of mating components should be devised.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.5
• /
• pp.582-595
• /
• 2003

Statement of problem : Most posts are metallic, but in response to the need for a post that possesses optical properties compatible with an all-ceramic crown. an esthetic post has been developed. Although there have been many studies about the esthetic post materials, 3-dimensional finite element studies about the stress distribution of them are in rare. Purpose : The purpose of this study is to investigate comparatively the distribution of stresses of the restored, endodontically treated maxillary incisors with the esthetic post materials and the displacement on the cement layer on simulated occlusal loading by using a 3-dimensional finite element analysis model. Material and method : Four 3-dimensional finite element models were constructed in a view of a maxillary central incisor, a post, a core, and the supporting tissues to investigate the stresses in various esthetic posts and cores and the displacement on the cement layer (Model 1 ; Cast gold post and core, Model 2 ; Glass fiber post with composite core, Model 3 ; Zirconia post with composite core. Model 4 ; Zirconia post with ceramic core). Force of 300N was applied to the incisal edge and the cingulum (centric stop point) with the angle of 135-degree to the long axis of the tooth. Results : 1. The stresses and displacement on the incisal edge were higher than on the cingulum 2. The stresses in dentin were the highest in Model 2 (Glass fiber post with composite core), and the second was Model 3, the third Model 1, and the lowest Model 4. 3. The stresses in post and core were the highest in Model 4 (Zirconia post with ceramic core), and the second was Model 1, the third Model 3, and the lowest Model 2. 4. The displacement on the cement layer was the highest in Model 2 (Glass fiber post with composite core), and the second was Model 3, the third Model 1, and the lowest Model 4. Conclusion : When a functional maximum bite force was applied, the distribution of stresses or the esthetic post and core materials and the displacement on the cement layer were a little different. It seems that restoring extensively damaged incisors with esthetic post and core materials would be decided according to the remaining tooth structure.