• Journal of information and communication convergence engineering
• /
• v.7 no.2
• /
• pp.209-214
• /
• 2009

The employment of the induction generator is preferable in the natural energy utilization by the minimum maintenance and the mechanical robustness, Another merit is also expected when it is connected to the power network system, because constant-voltage and constant frequency (CVCF) power generation is easily realized in spite of the variation of the rotor speed. However the induction generator needs much amount of the reactive power that reduces power factor in the primary side. The improvement of power factor in the primary side requires large VAR compensator, this point is solved, the merit of the induction machine as a main generator will become more established. This paper proposes a novel approach where the secondary is controlled by a PWM inverter not only to get CVCF power but also to improve the primary power factor. Basically the inverter is controlled so that the field current is supplied from the secondary side in this approach. The required capacity of the inverter is small, because only the slip power is controlled in the secondary side. In the experimental system where the sea wave torque simulator is used, the power factor is well improved by the microcomputer controlled PWM inverter.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.805-807
• /
• 2011

In this paper, we propose a method to inspect defects of injection molded automotive parts. In order to inspect them, we developed and used a line detection algorithm and a defect analysis algorithm. The line detection algorithm defines center point of a laser line and the inspection algorithm determines the defects of automotive parts using pattern data of inspected objects and the data results from the line detection algorithm. We evaluated the accuracy and the processing time of inspection and they showed good performance.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.7
• /
• pp.364-369
• /
• 2002

In this paper, 3-D magnetostatic finite element simulation of a rotux type Low-Tc superconducing (LTS) superconducting power supply, finite element method, cryogenic system, superconducting foil by generated magnetic flux from the rotating pole. The magnetic flux density on the superconducting foil caused by two exciters is therefore sufficiently greater than its critical magnetic flux density and it is an essential point in LTS power supply design. To establish the sufficient flux path of this machine, ferromagnetic materials is used in this power supply. When ferromagnetic materials is used at extremely low temperature, its characteristic of magnetization differs to that at room temperature. For this reason, special consideration is needed in the magnetic analysis of cryogenic systems. When the excitation current is 10A, the normal spot appears on superconducting foil. The results of this analysis are calculated and compared with the experimental results. The linkage flux due to the excitation current of 10, 20, 30, 40 and 50A are respectively $1.30{\times}10-4$, $2.67{\times}10-4$, $5.08{\times}10-4$ and $6.15{\times}10-4Wb$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.3
• /
• pp.440-449
• /
• 2003

Residual strength of fiber metal laminates after impact was studied. 3/4 lay up FML was fabricated using 4 ply prepreg, 2 ply aluminum sheets, and 1 ply steel sheet. Quasi isotropic ([0/45/90/-45]s) and orthotropic ([0/90/0/90]s) FRP were also fabricated to compare with FML. Impact test were conducted by using instrumented drop weight impact machine (Dynatup, Model 8250). Penetration load and absorbed energy of FML were superior to those of FRPs. Tensile tests were conducted to evaluate the residual strength after impact. Strength degradation of FML was less than that of FRP. This means that the damage tolerance of FML is excellent than that of FRP. Residual strength of each specimen was predicted by using Whitney and Nuismer(WN) Model. Impact damage area is assumed as a circular notch in WN model. Damage width is defined as the average of back face and top face damage width of each specimen. Average stress and point stress criterions were used to calculate the characteristic length. It is supposing that a characteristic length is a constant. The distribution of characteristic length shows that the assumption is reasonable. Prediction was well matched with experiment under both stress criterions.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.1
• /
• pp.45-51
• /
• 2014

Generally, marine transmissions contain straight shafts and helical gears, meaning that enginerooms require more space. In order to guarantee a levelengine space for conical involute gears or beveloid gears, both of which are important machine parts, a conical gear was used to replace the traditional cylinder gear. Owing to weak points such as the point contact phenomenon of the teeth, a limitation of the width of each tooth in terms of the addendum, the variational modification coefficient,and the difficulty of processing, research about conical involute gears remains at a standstill. Along with the increasing number of applications of conical involute gears, research on conical gear design technology is necessary. In this paper, in an effort to enhance conical gear design technology, research on the 3D modeling and stress analyses of helical conical involute gears were done.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.2
• /
• pp.310-317
• /
• 2013

In this paper, the contact pressure of the wafer and polishing pad for final polishing process for 300 mm-wafer were investigated through numerical analysis using FEM tool, ANSYS. The distribution of the contact pressure is one of main parameters which affects on the flatness and surface roughness of polished wafers. Two types of polishing head, a hard type head with ceramic disk and a soft type head with air bag were considered. The effects of the deformation and initial shape of table on the contact pressure were also examined. Both heads and tables were modeled as 3D finite element model from solid model, and the material properties of polishing pads and rubber plate for the air-bag head were obtained from tensile tests. The contact pressure deviation on wafer surface was smaller with air bag head than hard type head even when the table had form errors such as convex or concave. From this 3D analysis, it could be concluded that the air-bag head has better uniformity of the contact pressure on wafer. Also, the effects of inner diameter of air bag and radial clearance between wafer and retainer were investigated as view point of contact pressure concentration on the edge of wafer.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.15-19
• /
• 2001

A dedicated reverse engineering(RE) system for rapid manufacturing of human head in a 3D bust has been developed. The first step in the process is to capture the surface details of a human head and shoulder by three scanners based upon the digital moire fringe technique. Then the multiple scans captured from different angles are aligned and merged into a single polygonal mesh, and the aligned data set is refined by smoothing, subdividing or hole filling process. Finally, the refined data set is sent to a 4-axis computer numerically control(NC) machine to manufacture a replica. In this paper, we mainly describe on the algorithms and software for aligning multiple data sets. The method is based on the recently popular Iterative Closest Point(ICP) algorithm that aligns different polygonal meshes into one common coordinate system. The ICP algorithm finds the nearest positions on one scan to a collection of points on the other scan by minimizing the collective distance between different scans. We also integrate some heuristics into the ICP to enhance the aligning process. A typical example is presented to validate the system and further research work is also discussed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.4
• /
• pp.803-810
• /
• 1992

With increases in the rotational speed of hydraulic machine, studies on the hydrodynamic characteristics of supercavitating cascade are important on the view of flow analysis and design of fluid machinery. In the present paper, the complex functions of nonlinear theory corresponding to the flow of supercavitating cascade can be obtained by distributing singulary singulary points such as sources, vortexes and doublets on hydrofoil and free streamline. The numerical calculations on the closed wake model and semi-closed wake model are carried out in order to show the flow characteristics around the supecavitating cascade with finite with finite cavity length. As the result of this study, the flow characteristics such as lift, drag and cavitation coefficients are predicted by the flow conditions of supercavitating cascade in the fluid machinery.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.7
• /
• pp.749-753
• /
• 2013

Hydraulic systems are used to transform mechanical energy and fluid energy into each other. Its applications are very wide over the whole industries such as automobiles, public works, rockets, machine tools, construction heavy equipments, airplaces and so on. They are hydraulic pumps that transform energy in the systems. In this study, with basic operation principles as a start point, I tried to understand how the rotating radius of a piston affects the lubrication characteristics in more practical conditions, a swash-plate with tilt angle zero capable of rotating motion and other devices was used. In this paper, a slipper was located on 45mm eccentricity from the center of a swash-plate. As a result, through this experiment, it was found that the rotating radius of a piston affects load capacity, leakage flow and lubrication characteristics and it is one of the important parts for improving the pump efficiency.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.1
• /
• pp.86-91
• /
• 2008

The structural members must be designed to control characteristics of energy absorption for protecting passengers in a car accident. Study on collapse characteristics of structural member is currently conducted in parallel with other studies on effective energy absorption capacity of structural members with diverse cross-sectional shapes and various materials. This study concerns the crashworthiness of the widely used vehicle structural members, square thin-walled tubes, which are excellent in the point of the energy absorption capacity. The absorbed energy, mean collapse load and deformation mode were analyzed for side member which absorbs most of the collision energy. To predict and control the energy absorption, controller is designed in consideration of its influence on height, thickness and width ration in this study. The absorbed energy and mean collapse load of square tubes were increased by $15{\sim}20%$ in using the controller, and energy absorbing capability of the specimen was slightly changed by change of the high controller's height.