• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.113-114
• /
• 2016

영구자석형 동기전동기를 구동하는 인버터에서는 기본적으로 정현파 운전 방식을 사용하지만 최근에는 구형파 운전 방식도 종종 사용되고 있다. 정현파 운전 방식은 구형파 운전 방식에 비해 토크 리플이 작고 기동 성능이 우수하며, 약자속 제어를 이용하여 정격 속도 이상의 고속 운전이 가능하다. 이에 비해 구형파 운전 방식은 제어 알고리즘이 간단하고 스위칭 손실이 적은 장점이 있지만, 토크 리플이 크고 정격 속도 이하의 영역에서만 운전이 가능하다는 단점이 있다. 최근에 인버터의 운전 중에 각각의 장점이 있는 이들 2가지 운전 방식을 서로 전환하는 방법으로 가전제품의 압축기와 같은 연속 부하에 적용하기 위한 연구가 진행되었다. 저속 구간에서는 스위칭 손실을 줄이기 위하여 구형파 운전 방식을 주로 사용하고, 고속 구간에서는 안정적인 제어 성능을 위하여 정현파 운전 방식을 사용한다. 또한, 이 2가지 운전 방식의 전환 구간에서의 발생되는 과도 상태를 짧게 줄이기 위하여 속도 및 전류 제어기의 제어 변수에 대한 초기화 방법이 제시되었다. 본 논문에서는 구형파 운전 구간의 속도 제어기에 비례 적분 전류 제어기를 추가하여 전류 리플을 감소시키고, 전환 구간에서의 속도 및 전류 제어기의 제어 변수에 대한 초기화 방법을 제시하였다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.3
• /
• pp.267-274
• /
• 2004

In this paper, a new on-line dead-time compensation method is proposed. The output voltage errors due to the dead-time effect is considered as disturbance voltages. The magnitude of the disturbance voltages is estimated using a time delay control technique and the disturbance voltages are calculated using the estimated values, measured currents, and position information. The calculated disturbance voltages are fed to voltage references in order to compensate the dead-time effect. The proposed method is applied to a PM synchronous motor drive system and implemented in a digital manner using a digital signal processor (DSP) TMS320C31. The experiments are carried out for this system to show the effectiveness of the proposed method and the results show the validity of the proposed method.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.461-466
• /
• 2003

This paper presents the speed control of the surface-mounted permanent-magnet synchronous motors (SMPMSM) for the elevator drive. The elevator motor needs to be a compact and slim type. Essentially, the proposed scheme uses a vector control algorithm for a speed and torque control. This system is implemented using a high speed 32-bit DSP (TMS320C31-50), a high-integrated logic device FPGA (EPF10K10-Tl144-3) to design compactly and Inexpensively The proposed scheme is verified through digital simulation and experiments for a three-phase 13.3kW SMPMSM as a MRL(MachineRoomless) elevator motor ill the laboratory. Finally, experiment of the test tower was performed with a 48kW PWM converter-inverter system for a high- speed elevator .

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.1
• /
• pp.1-7
• /
• 2012

The brake-by-wire technology is a new automotive chassis system that allows standard braking operations by electronic components with lighter weights and faster response. The brake-by-wire units such as EMB (Electro-Mechanical Brake) are controlled by electronic sensors and actuators and, thus, the fault diagnosis is essential for implementation. In this study, a model-based fault diagnosis system is developed for the sensors based on the analytical redundancy method. The fault detection algorithm is verified in simulations for various faulty cases. A test bench is built including the EMB unit and the performance of the proposed fault diagnosis system is evaluated through the experiment.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.1
• /
• pp.53-60
• /
• 2012

As enforced by the regulation on the improving fuel efficiency and increased the demand on green technology, many interests are focused on electric vehicles and hybrid vehicles. Thus the technology development in electrification of vehicle operation system, including steering and braking field, is actively progressive. Especially electric power steering substitutes for hydraulic power steering rapidly in the market, which is more complex and bigger in packaging volume compared with electric power steering system. The core component in electric power steering system is a motor, which is required to be silent and powerful to guarantee required system performance. Brushless synchronous motors are widely used and many variations of the motors are introduced in the market, while the performance of each type is not well defined or studied for electric power steering system. In this paper, recent developments in brushless synchronous motor are reviewed and compared applying finite element analysis in electromagnetic field. As results, each characteristic of different types of brushless synchronous motors is compared and summarized for optimized selection in electric power steering system.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.4
• /
• pp.193-199
• /
• 2011

The next generation domestic high speed railway system is a power distributed type and uses vector control method for motor speed control. Nowadays, inverter driven induction motor system is widely used. However, recently PMSM drives are deeply considered as a alternative candidate instead of an induction motor driven system due to their advantages in efficiency, noise reduction and maintenance. The next-generation high-speed train is composed of 2 converter units, 4 inverter units, and 4 Traction Motor units. Each motor is connected to the inverter directly. In this paper, the effects of IPMSM parameter variation to the system operation characteristics of the multi inverter driven high speed train system are investigated. The parallel connected inverter input-output characteristics are analyzed to the parameter mismatches of the IPMSM in 1C1M control using Matlab/Simulink, then the reliability of the simulation results are verified through experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.5
• /
• pp.457-462
• /
• 2014

Given their low cost, single rolling piston compressors (SRPC) are utilized in low-power room air-conditioning systems. The SRPC cycle is composed of one compression and discharge process per mechanical rotation. The load torque is high during the compression process of the refrigerants and low during the discharge process of the refrigerants. This load torque variation induces a speed ripple and severe vibration, which cause fatigue failures in the pipes and compressor parts, particularly under low-speed conditions. To reduce the vibration, the compressor usually operates at a high-speed range, where the rotor and piston inertia reduce the vibration. At a low speed, a predefined feed-forward load torque compensator is used to minimize the speed ripple and vibration. However, given that the load torque varies with temperature, pressure, and speed, a predefined load torque table based on one operating condition is not appropriate. This study proposes an online load torque compensator for SRPC. The proposed method utilizes the speed ripple as a load torque ripple factor. The speed ripple is transformed into a frequency domain and compensates each frequency harmonic term in an independent feed-forward manner. Experimental results are presented to verify the proposed method.

• Proceedings of the KIEE Conference
• /
• 2007.04c
• /
• pp.97-99
• /
• 2007

This paper presents a fuzzy logical control method to implement an on-line optimum efficiency control for Permanent Magnet Synchronous Motor. This method real-timely adjusts the output voltage of the inverter system to achieve the optimum running efficiency of the whole system. At first, the input power is calculated during the steady state in the process of efficiency optimizing. To exactly estimate the steady state of the system, this section needs check up the speed setting on timely. The second section is to calculate input power of dc-bus. The exact measurement of the voltage and current is the vital point to acquire the input power. The third section is the fuzzy logic control unit, which is the key of the whole drive system. Based on the change of input power of dc-bus and output voltage, the variable of output voltage is gained by the fuzzy logical unit. With the on-line optimizing. the whole system call fulfill the minimum input power of dc-bus on the running state. The experimental result proves that the system applied the adjustable V/f control method and the efficiency-optimizing unit possesses optimum efficiency, and it is a better choice for simple variable speed applications such as fans and pump.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.5
• /
• pp.620-625
• /
• 2013

This paper presents the design of a switched reluctance motor (SRM) for electric air conditioning compressors which are applied to hybrid electric vehicles (EVs). The motor for driving air conditioning compressor which is recently used on EV(electric vehicle) / HEV (hybrid electric vehicle) is PMSM(permanent magnet synchronous motor) or BLDCM(brushless DC motor). However disadvantage of motors that uses permanent magnets are vulnerable to high temperatures because of the demagnetization by the high temperature and the permanent magnet is expensive because of the high price of rare earth materials from China's monopoly. Therefore, in the automotive insustry is interested in the non-rare-earth motors. SRM has many advantages. it's resistant to high temperatures, price is cheaper, because there are no permanent magnets and winding in the rotor. Also it's high relability and efficiency, suitable for high-speed operation because of structure is simple. In this paper, the SRM, non-rare-earth motor, are designed, analyzed and experimented drive to replace an existing electric compressor drive motor.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1566-1574
• /
• 2017

When the inter-turn short circuit (ITSC) fault occurs, the distortion of the magnetic field is serious. The motor loss variations of each part are obvious, and the motor temperature field is also affected. In order to obtain the influence of the ITSC fault on the motor temperature distribution, firstly, the normal and the fault finite element models of the permanent magnet synchronous motor (PMSM) were established. The magnetic density distribution and the eddy current density distribution were analyzed, and the mechanism of loss change was revealed. The effects of different forms and degrees of the fault on the loss were obtained. Based on the loss analysis, the motor temperature field calculation model was established, and the motor temperature change considering the loop current was analyzed. The influence of the fault on the motor temperature distribution was revealed. The sensitivity factors that limit the motor continuous operation were obtained. Finally, the correctness of the simulation was verified by experiments. The conclusions obtained are of great significance for the fault and high temperature demagnetization of the permanent magnet analysis.