• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.5
• /
• pp.364-370
• /
• 2009

This study was conducted to survey, analyze on the compaction layer and the plow layer at Jeonbug and Jisan series paddy soil, which is the representative soil in fluvio-marine and local alluvium, respectively. The depths of surface soil were 12.6 and 12.7 cm in Jeonbug and Jisan series, respectively. A plowing depth was 10.5 cm. The properties of compaction layer in two soil series were as follows. The hardness were $14.7kg\;cm^{-2}(25.3mm)$ and $8.7kg\;cm^{-2}(22.1mm)$ in Jeonbug and Jisan series, respectively. The thickness were 22.3 cm and 17.8 cm in Jeonbug and Jisan series, respectively. The depth of soil compaction, which means depth from surface, were 15 and 20 cm in Jeonbug and Jisan series, respectively. The relationship between the hardness of compaction layer and the depth of surface soil showed negative correlation, however relationship between the hardness and the thickness of compaction layer showed positive correlation. Soil temperature was lower in compaction layer than in plow layer. This temperature differences between compaction layer and plow layer were from 1.0 to $2.5^{\circ}C$ in Jeonbug series and from 0.7 to 2.1 in Jisan series. The soil physical properties of compaction layer were higher in bulk density and solid phase and lower in porosity and gaseous phase than those of plow layer in all soil series. The soil chemical properties of compaction layer were higher in pH, content of available silicate, exchangeable calcium and magnesium but lower in total nitrogen, content of organic matter and available phosphate than those of plow layer in all soil series. Cation exchangeable capacity and content of exchangeable potassium were similar between compaction layer and plow layer in Jeonbug series, however, in Jisan series these were lower in compaction layer than in plow layer. Elution amount of inorganic nitrogen were lower in compaction layer than in plow layer in all soil series. The content of soluble Fe and Mn were plenty in compaction layer compared with plow layer and these tendency was apparent in Jeonbug series. The water depth decrease were fast until the latter part of June, and were slow as $1{\sim}3mm\;day^{-1}$ for July and August, and were fast again from september. Rice roots distributions as each soil series and tillage method were 25 cm at rotary plowing in Jeonbug series, 30 cm at deep plowing in Jeonbug series, and 20 cm at tillage in Jisan series. Dry weight per m2 at heading stage were much in order of deep plowing in Jeonbug series, rotary plowing in Jeonbug series, and tillage in Jisan series.

• Journal of Biosystems Engineering
• /
• v.36 no.6
• /
• pp.397-406
• /
• 2011

In this study, surveys on operation status of the 73 tractors with rated power of over 75 kW from six provinces in Korea were performed to obtain basic data required for development and efficient use of the high-power and high-performance tractors. And types of tractors and implements, operation crops, types of operations, annual operation areas, annual operation days, annual operation hours, operation speeds and widths, and problems and improvements in use were investigated. Most (91.7%) of the tractor surveyed were operated for forage and silage crops such as rice straw, whole barley, rye grass, reed canary grass, sudan grass, and the remains were operated for upland crops such as ginseng, sweet potato, potato, chinese cabbage, radish. Main operations of the tractors were cutting, baling, and wrapping for forage crops, plow tillage, rotary tillage, and manure spreading. About half (47.9%) of the tractors were used exclusively for forage crop harvesting such as forage crop cutting, forage baling, and bale wrapping, 24.5% of the tractors were used exclusively for plow or rotary tillage, and 27.4% of the tractors were used for both forage crop harvesting, and plow or rotary tillage. For the tractors with power ranges of 75~83, 89~94, 98~101, 113, 124 kW, average annual operation areas per tractor for plow tillage, rotary tillage, forage crop harvesting (cutting, baling, wrapping), and manure spreading operations were analyzed as 112.6. 144.8, 158.9. 390.0. 215.6 ha, respectively. and total average annual operation area per tractor was 171.3 ha. Average annual operation days per tractor for those operations were analyzed as 24.1, 28.9, 38.3, 55.4, 33.4, respectively, and total average annual operation days per tractor was 33.6. Average annual operation hours per tractor for them were analyzed as 260.0, 321.6, 408.1, 664.8, 413.8, respectively, and total average annual operation hours per tractor for the all tractors was 377.1. Ranges of operation widths of plow tillage, rotary tillage, forage crop cutting, forage baling, bale wrapping, and manure spreading operations were shown as 1.5~2.6, 2.3~3.0, 1.8~3.2, 1.8~2.0, 1.8~2.3, 3.1~6.6 m, respectively. Ranges of operation speed of plow tillage, rotary tillage, forage crop cutting, forage baling, bale wrapping, and manure spreading were shown as 6~9, 4~11, 9~16, 8~15, 8~17, 12~16 km/h, respectively.

• Korean Journal of Agricultural Science
• /
• v.50 no.3
• /
• pp.383-394
• /
• 2023

In Korea, the U.S. Tier-4 Final emission standards have been applied to agricultural machinery since 2015. This study was conducted to analyze the emission characteristics of agricultural tractors during plow tillage operations using PEMS (portable emissions measurement systems). The tractor working speed was set as M2 (5.95 km/h) and M3 (7.60 km/h), which was the most used gear stage during plow tillage operation. An engine idling test was conducted before the plow tillage operation was conducted because the level of emissions differed depending on the temperature of the engine (cold and hot states). The estimated level of emissions for the regular area (660 m²), which was the typical area of cultivation, was based on an implement width of 2.15 m and distance from the work area of 2.2 m. As a result, average emission of CO (carbon monoxide), THC (total hydrocarbons), NOx (nitric oxides), and PM (particulate matter) were approximately 6.17×10-2, 3.36×10^-4, 2.01×10^-4, and 6.85×10^-6 g/s, respectively. Based on the regular area, the total emission of CO, THC, NOx, and PM was 2.62, 3.76×10^-2, 1.63, and 2.59×10^-4 g, respectively. The results of total emission during plow tillage were compared to Tier 4 emission regulation limits. Tier 4 emission regulation limits means maximum value of the emission per consumption power (g/kWh), calculated as ratio of the emission and consumption power. Therefore, the total emission was converted to the emission per power using the rated power of the tractor. The emission per power was found to be satisfied below Tier 4 emission regulation limits for each emission gas. It is necessary to measure data by applying various test modes in the future and utilize them to calculate emission because the emission depends on various variables such as measurement environment and test mode.

• Korean Journal of Soil Science and Fertilizer
• /
• v.49 no.4
• /
• pp.300-309
• /
• 2016

The monolithic weighing lysimeter is a useful facility that could directly measure water movement via layers, drainage, and evapotranspiration (ET) with precise sensors. We evaluated water movement through layers and water balance using the lysimeter with undisturbed paddy sandy loam soil, Gangseo soil series (mesic family of Anthraquic Eutrudepts classified by Soil Taxonomy) during winter season from Dec. 2014 to Feb. 2015. Daily ET indicated up to 1.5 mm in December and January and 2 mm in February. The abrupt increase of soil water tension at the depth of 0.1 m, when soil temperature at the same depth was below $2^{\circ}C$, was observed due to temporary frost heaving. The surface evaporation was less than reference ET below -15 kPa of soil water potential at the depth of 0.1 m. The maximum drainage rate was similar to the saturated hydraulic conductivity of a plow pan layer. Both upward and downward water movement, related to ET and drainage, were retarded by a plow pan layer. This study demonstrated that the lysimeter study could well quantify water balance components even under frost heaving during winter season and that a plow pan with low permeability could act as a boundary that affects drainage and evapotranspiration.

• Journal of Drive and Control
• /
• v.16 no.4
• /
• pp.23-31
• /
• 2019

The purpose of this study was to evaluate the PTO severeness for an agricultural tractor during disk plow and rotary tillage. The PTO load measurement system was constructed with data acquisition and a PTO torquemeter. Field experiments were conducted at a combination of traveling speed (L3 Low, L3 High) and PTO speed (P1, P2). The load spectrum was generated using the rain-flow counting method, and the SWT method was used to consider the range and mean of the PTO load. The damage sum was calculated by applying a modified miner rule, which is a cumulative damage law. The relative severeness was expressed as the ratio of the lowest damage sum. Relative severeness was higher with the lower PTO gear stage, and higher driving gear stage and it was approximately 40-102 times higher for rotary tillage than disk plow tillage in the same gear stages. The relative severeness was 1010.12 in the rotary tillage under L3 High P1 based on the disk plow tillage under L3 Low P2.

• Archives of Plastic Surgery
• /
• v.34 no.4
• /
• pp.490-492
• /
• 2007

Purpose: Nipple reconstruction is an important step in breast reconstruction after mastectomy. There are considerable number of reconstructive methods developed over the past years. Each of these has not only its own special advantages, but also limitations. Therefore, no single method has become the overwhelming favorite. Sometimes it seems to be compromised when the nipple must be located directly over a linear scar. Methods: A 48-year-old female patient received a central lumpectomy with circumareolar resection of the nipple areolar complex 4 months ago. The newly designed nipple must be positioned directly astride a scar. We drew two equal-sized rectangular flaps sharing a common limb on a transverse scar and the result was two opposing plow form. Each flap size was about 1.3 cm wide and 2.5 cm long. First we elevated the flap from the distal part at a deep dermal plane, then deepened the level of dissection to raise the dermal-fat flaps. The donor site could be closed directly without any dog-ear deformity. Then we folded down the elevated flaps and loosely sutured skin with nonabsorbable materials. Each flap inner side was approximated side by side. Finally we made new natural nipple with 6 mm projection. We applied tattooing in the areola area with micropigmentation device after three months. Results: After ten months of follow-up periods, the nipple projection was stable and symmetric. The nipple projection was 3.1 mm, compared with 2.8 mm for the opposite nipple. Conclusion: Our experiences shows that this double opposing plow flap is a particularly useful and simple technique when there is a traverse scar crossing the center of the proposed nipple area.

• Journal of Biosystems Engineering
• /
• v.31 no.1 s.114
• /
• pp.9-15
• /
• 2006

Draft control is key technique in plow control system for automation of implement control system. To make the consistent draft force is an essential factor for preventing the reduction of working efficiency by tractor's slip and also improving the working efficiency. Therefore, the purpose of this study is to develop the draft sensor for draft control of plow and evaluate the usability of the algorithm of draft control system using proportional control valve. The developed draft control system could extract the draft force very well regardless of draft condition, change of setting draft force and response time in the response characteristic test. The maximum draft force at 3-Point linkage was 10,000 N and the deviation of the control system was 125.8 N in steady state condition. The developed control system worked very well with regard to the change of draft force in field and even in soil condition with soil reaction. The results of experiment showed the characteristics of response was sufficient to be used as the implement draft control system for tractor using proportional valve.

• Korean Journal of Agricultural Science
• /
• v.42 no.3
• /
• pp.183-189
• /
• 2015

Plant root penetration through soil profile is restricted by compacted layer such as plow pan under conventional tillage. For detecting the compact layer, we made a graduated T-shape probe and measured compared between the depths with rapid change in feeling hardness of hand penetration using T-shape probe and with a rapid increase of penetrometer cone index. On upland crops, including red pepper, corn, soybean and cucumber, plow pan depth ranged from 10 cm to 25 cm depth. The effective rooting depth (ER) had significant correlation with the plow pan depth (PP) except soils with the shallow ground water and/or poorly drained soil. The regression equation was ER = 0.9*PP ($R^2=0.54^{**}$, N = 14) with the applicative PP range of 10-25 cm.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.57 no.1
• /
• pp.89-97
• /
• 2012

Reduction of greenhouse gas (GHG) emissions from upland crop field as well as paddy field is being required, but little information on GHG emissions according to cultivation practices in upland field is available. Soil GHG emissions during the growing season were investigated in the field of three decades rotation and tillage treatments which were consisted of plow, chiesl tillage and no tillage in west central Indiana, USA in 2006. Seasonal cumulative $CO_2$ emissions were not different among treatments. $CH_4$ emission increased a little in plow tillage during early soybean growing season. Most of $N_2O$ emission occurred during early corn growing season after N-fertilizer application from mid June to mid July, and was significantly affected by tillage practices in which seasonal cumulative $N_2O$ emission was significantly higher under chisel tillage. $N_2O$ emission under no-tillage was lower about 64% and 39% than that under chisel tillage and plow tillage, respectively. No-tillage practice with rotation of corn and soybean seems to be promising in point of less GHG emission and less labor for cultivation without grain yield reduction.

• Korean Journal of Soil Science and Fertilizer
• /
• v.18 no.2
• /
• pp.140-147
• /
• 1985

This experiment was conducted in the field to investigate the effects of mulched condition on nutrient's mineralization and its mobility as affected by environmental changes (soil moisture and soil temperature) in the plow layer. 1. Nitrogen mineralization was faster owing to the prevention of evaporation and the increase of soil temperature in the poly ethylene mulched plot. As a result, nitrate form of nitrogen was much earlier available for plant in mulched plot than in non mulched plot. 2. Available $P_2O_5$ content in the plow layer was kept highest in the fertilized zone (10-20 cm depth) regardless of difference between mulched and non mulched condition, and was nearly constant without showing difference between planting and non planting of tobacco due to the lower availability of phosphorus by tobacco. 3. Potassium applied in the plow layer was remained a large quantity until the latter growth stage resulting in the lower recovery of potassium by tobacco. 4. Mineralized nutrients such as $NH_4-N$, $NO_3-N$, and K in the plow layer of mulched plot were transported from the fertilized layer (10-20 cm depth) and accumulated to the surface layer (0-10 cm depth) as the growing time goes by, but those in non mulched plot were distributed to the deeper layer. 5. Mobility of available nutrients in the plow layer was If order as $NO_3-N$ $$\geq_-$$ $NH_4-N$ > K > available $P_2O_5$. 6. Leaching degree of mineralized nutrients in the mulched plot was much lower than in the non mulched plot.