• Journal of the Korean Geotechnical Society
• /
• v.22 no.6
• /
• pp.71-82
• /
• 2006

One of the most popular pre-reinforcement methods of tunnel heading in cohesionless soils would be the fore-polling of grouted pipes, known as RPUM (reinforced protective umbrella method) or UAM (umbrella arch method). This technique allows safe excavation even in poor ground conditions by creating longitudinal arch parallel to the tunnel axis as the tunnel advances. Some previous studies on the reinforcing effects have been performed using numerical methods and/or laboratory-based small scale model tests. The complexity of boundary conditions imposes difficulties in representing the tunnelling procedure in laboratory tests and theoretical approaches. Full-scale study to identify reinforcing effects of the tunnel heading has rarely been carried out so far. In this study, a large scale model testing for a tunnel in granular soils was performed. Reinforcing patterns considered are four cases, Non-Reinforced, Crown-Reinforced, Crown & Face-Reinforced, and Face-Reinforced. The behavior of ground and pipes as reinforcing member were fully measured as the surcharge pressure applied. The influences of reinforcing pattern, pipe length, and face reinforcement were investigated in terms of stress and displacement. It is revealed that only the Face-Reinforced has decreased sufficiently both vertical settlement in tunnel heading and horizontal displacement on the face. Vertical stresses along the tunnel axis were concentrated in tunnel heading from the test results, so the heading should be reinforced before tunnel advancing. Most of maximum axial forces and bending moments for Crown-reinforced were measured at 0.75D from the face. Also it should be recommended that the minimum length of the pipe is more than l.0D for crown reinforcement.

• The Korean Journal of Air & Space Law and Policy
• /
• v.30 no.2
• /
• pp.201-248
• /
• 2015

In Korea the number of unlawful interference act on board aircrafts has been increased continuously according to the growth of aviation demand, and there were 55 incidents in 2000, followed by 354 incidents in 2014, and an average of 211 incidents a year over the past five years. In 1963, a number of states adopted the Convention on Offences and Certain Other Acts Committed on Board Aircraft (the Tokyo Convention 1963) as the first worldwide international legal instrument on aviation security. The Tokyo Convention took effect in 1969 and, shortly afterward, in 1970 the Convention for the Suppression of Unlawful Seizure of Aircraft(the Hague Convention 1970) was adopted, and the Convention for the Suppression of Unlawful Acts Against the Safety of Civil Aviation(the Montreal Convention 1971) was adopted in 1971. After 9/11 incidents in 2001, to amend and supplement the Montreal Convention 1971, the Convention on the Suppression of Unlawful Acts Relating to International Civil Aviation(the Beijing Convention 2010) was adopted in 2010, and to supplement the Hague Convention 1970, the Protocol Supplementary to the Convention for the Suppression of Unlawful Seizure of Aircraft(the Beijing Protocol 2010) was adopted in 2010. Since then, in response to increased cases of unruly behavior on board aircrafts which escalated in both severity and frequency,, the Montreal Protocol which is seen as an amendment to the Convention on Offences and Certain Other Acts Committed on Board Aircraft(the Tokyo Convention 1963) was adopted in 2014. Korea ratified the Tokyo Convention 1963, the Hague Convention 1970, the Montreal Convention 1971, the Montreal Supplementary Protocol 1988, and the Convention on the Marking of Plastic Explosive 1991 which have proven to be effective. Under the Tokyo Convention ratified in 1970, Korea further enacted the Aircraft Navigation Safety Act in 1974, as well as the Aviation Safety and Security Act that replaced the Aircraft Navigation Safety Act in August 2002. Meanwhile, the title of the Aviation Safety and Security Act was changed to the Aviation Security Act in April 2014. The Aviation Security Act is essentially an implementing legislation of the Tokyo Convention and Hague Convention. Also the language of the Aviation Security Act is generally broader than the unruly and disruptive behavior in Sections 1-3 of the model legislation in ICAO Circular 288. The Aviation Security Act has reflected the considerable parts of the implementation of national legislation under the Beijing Convention and Beijing Protocol 2010, and the Montreal Protocol 2014 that are the modernized international conventions relating to aviation security. However, in future, when these international conventions would come into effect and Korea would ratify them, the national legislation that should be amended or provided newly in the Aviation Security Act are as followings : The jurisdiction, the definition of 'in flight', the immunity from the actions against the aircraft commander, etc., the compulsory delivery of the offender by the aircraft commander, etc., the strengthening of penalty on the person breaking the law, the enlargement of application to the accomplice, and the observance of international convention. Among them, particularly the Korean legislation is silent on the scope of the jurisdiction. Therefore, in order for jurisdiction to be extended to the extra-territorial cases of unruly and disruptive offences, it is desirable that either the Aviation Security Act or the general Crime Codes should be revised. In conclusion, in order to meet the intelligent and diverse aviation threats, the Korean government should review closely the contents of international conventions relating to aviation security and the current ratification status of international conventions by each state, and make effort to improve the legislation relating to aviation security and the aviation security system for the ratification of international conventions and the implementation of national legislation under international conventions.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.2
• /
• pp.125-132
• /
• 1990

The authors carried out an experiment to investigate the responsive behavior of sea eel, Astroconger myriaster(BREVOORT) to chemical stimuli. The experimental tank was made in doughnut type by using FRP plates. The channel of tank was divided into three concentric troughs by using perforated plastic plates. The inside trough was used as influent part, the outside one as effluent part, and the middle one as the testing trough in which testing fish may be swimmable. The influent part was radially portioned into 12 sections so as to be 30 degrees of central angle. But a basin of any section in testing trough was diverged in the range of 45 degrees of central angle. The the testing trough are radially divided into eight zones. Water is supplied at the rate of 6.3l per minute from the central water tank set as high as 50cm in the center of doughnut, passed across the influent part, testing trough, effluent part and finally discharged by overflow pipes. The chemical substance to stimulate the sea eel was extracted from mackerel, shad and krill which are used as bait for fishing. The chemical substance was injected into any one of 12 hoses which supplies water from central water tank to the influent part at the rate of 2ml per minute. Sea eels used for the experiment were caught by pot in the coast of Chung-mu and accustomed to the tanks for 5 days before applying them to the experiment. The result obtained are as follows: 1. The rate of time length of sea eel's staying in the stimulated zone, as the extracts of mackerel, shad and krill were given to it, was observed as 7.9%, 30.9% and 11.4% respectively. It means that the extract from shad was the most effective of three in attracting sea eel. 2. To compare the effect of freshness of bait fish, the extracts were prepared from shad just killed, form the 24 hour-lapsed one and from the 48 hour-lasped one after killed. The rate of time length of sea eel's staying in the stimulated zone was 30.9%, 17.1% and 11.3% respectively. It means that the freshness is much effective in attracting olfactory fishes like sea eel.

• Korean Journal of Environmental Biology
• /
• v.37 no.4
• /
• pp.625-639
• /
• 2019

Microplastics are one of the substances threatening the marine ecosystem. Here, we summarize the status of research on the effect of microplastics on marine life and suggest future research directions. Microplastics are synthetic polymeric compounds smaller than 5 mm and these materials released into the environment are not only physically small but do not decompose over time. Thus, they accumulate extensively on land, from the coast to the sea, and from the surface to the deep sea. Microplastic can be ingested and accumulated in marine life. Furthermore, the elution of chemicals added to plastic represents another risk. Microplastics accumulated in the ocean affect the growth, development, behavior, reproduction, and death of marine life. However, the properties of microplastics vary widely in size, material, shape, and other aspects and toxicity tests conducted on several properties of microplastics cannot represent the hazards of all other microplastics. It is necessary to evaluate the risks according to the types of microplastic, but due to their variety and the lack of uniformity in research results, it is difficult to compare and analyze the results of previous studies. Therefore, it is necessary to derive a standard test method to estimate the biological risk from different types of microplastics. In addition, while most of the previous studies were conducted mostly on spheres for the convenience of the experiments, they do not properly reflect the reality that fibers and fragments are the main forms of microplastics in the marine environment and in fish and shellfish. Furthermore, studies have been conducted on additives and POPs (persistent organic pollutants) in plastics, but little is known about their toxic effects on the body. The effects of microplastics on the marine ecosystems and humans could be identified in more detail if standard testing methods are developed, microplastics in the form of fibers and fragments rather than spheres are tested, and additives and POPs are analyzed. These investigations will allow us to identify the impact of microplastics on marine ecosystems and humans in more detail.

• Journal of Korean Society of Steel Construction
• /
• v.25 no.2
• /
• pp.115-130
• /
• 2013

In this study, lateral-torsional buckling (LTB) strength of high-strength H-beams built up from 800MPa tensile-strength steel was experimentally and analytically evaluated according to current lateral stability provisions (KBC 2009, AISC-LRFD 2010). The motivation was to evaluate whether or not current LTB provisions, which were originally developed for ordinary steel with different stress-strain characteristics, are still applicable to high-strength steel. Two sets of compact-section specimens with relatively low (Set A) or high (Set B) warping stiffness were prepared and tested under uniform moment loading. Laterally unbraced lengths of the test specimens were controlled such that inelastic LTB could be induced. All specimens exhibited LTB strength exceeding the minimum limit required by current provisions by a sufficient margin. Moreover, some specimen in Set A reached a rotation capacity required for plastic design, although its laterally unbraced length belonged to the inelastic LTB range. All the test results indicated that extrapolation of current provisions to high-strength steel is conservative. In order to further analyze the test results, the relationship between inelastic moment and laterally unbraced length was also derived in explicit form for both ordinary- and high-strength steel based on the effective tangent modulus of inelastic section. The analytical relationship derived again showed that extrapolation of current laterally unbraced length limit leads to a conservative design in the case of high-strength steel and that the laterally unbraced length to control the inelastic LTB behavior of high-strength steel beam should be specified by including its unique post-yield strain-hardening characteristics.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.4
• /
• pp.233-252
• /
• 2021

This paper is a study to improve the efficiency of mixing technology in the shield TBM chamber. Currently, the number of construction cases using the TBM method is increasing in Korea. According to the increasing use of TBM method, research on TBM method such as Disc Cutter, Cutter bit, and Segment also shows an increasing trend. However, there is little research on the mixing efficiency in chamber and chamber. In order to improve the smooth soil treatment and the behavior of the excavated soil, a study was conducted on the change of the mixing efficiency according to the effective mixing bar arrangement in the chamber. In the scale model experiment, the ground was composed using plastic materials of different colors for ease of identification. In addition, the mixing bar arrangement was different and classified into 4 cases, and the particle size distribution was classified into single particle size and multiple particle size, and the experiment was conducted with a total of 8 cases. The rotation speed of the cutter head of all cases was the same as 5 RPM, and the experiment time was also carried out in the same condition, 1 minute and 30 seconds. In order to check the mixing efficiency, samples at the upper, middle (left or right), and lower positions of each case were collected and analyzed. As a result of the scaled-down model experiment, the mixing efficiency of Case 4 and Case 4-1 increased compared to Case 1 and Case 1-1, which are actually used. Accordingly, it is expected that the mixing efficiency can be increased by changing the arrangement of the mixing bar in the chamber, and it is considered to be effective in saving air as the mixing efficiency increases. Therefore, this study is considered to be an important indicator for the use of shield TBM in Korea.

• Economic and Environmental Geology
• /
• v.54 no.2
• /
• pp.233-245
• /
• 2021

Many studies on the microstructures in rocks have been conducted using experimental methods with various equipment as well as natural rock studies to see the development of microstructures and understand their mechanisms. Grain boundary migration of mineral aggregates in rocks could cause grain growth or grain size changes during metamorphism or deformation as one of the main recrystallization mechanisms. This study suggests improved ways regarding the analog material experiments with reformed equipment to see sequential observations of these grain boundary migration. It can be more efficient than the existing techniques and carry out an appropriate microstructure analysis. This reformed equipment was implemented to enable optical manipulation by mounting polarizing plates capable of rotating operation on a stereoscopic microscope and a deformation rig capable of experimenting with analog materials. The equipment can automatically control the temperature and strain rate of the deformation rig by microcontrollers and programming and can take digital photomicrographs with constant time intervals during the experiment to observe any microstructure changes. The composite images synthesized using images by rotated polarizing plates enable us to see more accurate grain boundaries. As a rock analog material, norcamphor(C7H10O) was used, which has similar birefringence to quartz. Static grain growth and simple shear deformation experiments were performed using the norcamphor to verify the effectiveness of the equipment. The static grain growth experiments showed the characteristics of typical grain growth behavior. The number of grains decreases and the average grain size increases over time. These case experiments also showed a clear difference between the growth curves with three temperature conditions. The result of the simple shear deformation experiment under the medium temperature-low strain rate showed no significant change in the average grain size but presented the increased elongation of grain shapes in the direction of about 53° regarding the direction perpendicular to the shearing direction as the shear strain increases over time. These microstructures are interpreted as both the plastic deformation and the internal recovery process in grains are balanced by the deformation under the given experimental conditions. These experiments using the reformed equipment represent the ability to sequentially observe changing the microstructure during experiments as desired in the tests with the analog material during the entire process.

• Journal of the Korean GEO-environmental Society
• /
• v.22 no.6
• /
• pp.17-26
• /
• 2021

Ground investigation and result analysis generally used to examine all sorts of structures' subsidence or stability can be classified into sandy soil and cohesive soil, and analysis on the liquid limit of soil is utilized to evaluate the physical properties of ground and types or technical behavior of soil. The most widely used method to analyze liquid limit is Casagrande with which liquid limit can be calculated relatively easily; however, it is fairly difficult to apply it to soil equipped with intermediate properties. Therefore, concerning the properties of soil having the intermediate properties of sedimentary ground, this researcher mixed the clay from Yangsan, Gwangyang, and Busan with sandy soil to make intermediate soil and then carried out the test of consistency limit and also evaluated applicability by using the suggested formula of consistency revision. The sample of intermediate soil was the mixture of clay and sandy soil, and to produce intermediate soil, the content (F_c) of fine soil was applied as 50%, 75%, or 100%. Regarding the physical properties of intermediate soil, to maintain the properties of clay in the natural state, bentonite was added at a fixed rate for controlling the properties of clay, and then, consistency was analyzed. By adopting the formula of consistency revision suggested in advanced research, this author analyzed consistency based on the experiment and consistency based on the suggested formula of revision. Also, about intermediate soil collected at the site, consistency based on the experiment and consistency based on the suggested formula of revision were analyzed comparatively, and about intermediate soil collected, this researcher analyzed particle size and calculated the content (F_c) of fine soil to analyze intermediate soil in diverse conditions. Moreover, about intermediate soil collected at the site, the suggested formula of consistency revision was applied to calculate the compression index, and the compression index based on the experiment and the compression index based on the suggested formula were analyzed comparatively to evaluate the applicability of the suggested formula.

• Journal of Intelligence and Information Systems
• /
• v.21 no.2
• /
• pp.69-92
• /
• 2015

The explosion of social media data has led to apply text-mining techniques to analyze big social media data in a more rigorous manner. Even if social media text analysis algorithms were improved, previous approaches to social media text analysis have some limitations. In the field of sentiment analysis of social media written in Korean, there are two typical approaches. One is the linguistic approach using machine learning, which is the most common approach. Some studies have been conducted by adding grammatical factors to feature sets for training classification model. The other approach adopts the semantic analysis method to sentiment analysis, but this approach is mainly applied to English texts. To overcome these limitations, this study applies the Word2Vec algorithm which is an extension of the neural network algorithms to deal with more extensive semantic features that were underestimated in existing sentiment analysis. The result from adopting the Word2Vec algorithm is compared to the result from co-occurrence analysis to identify the difference between two approaches. The results show that the distribution related word extracted by Word2Vec algorithm in that the words represent some emotion about the keyword used are three times more than extracted by co-occurrence analysis. The reason of the difference between two results comes from Word2Vec's semantic features vectorization. Therefore, it is possible to say that Word2Vec algorithm is able to catch the hidden related words which have not been found in traditional analysis. In addition, Part Of Speech (POS) tagging for Korean is used to detect adjective as "emotional word" in Korean. In addition, the emotion words extracted from the text are converted into word vector by the Word2Vec algorithm to find related words. Among these related words, noun words are selected because each word of them would have causal relationship with "emotional word" in the sentence. The process of extracting these trigger factor of emotional word is named "Emotion Trigger" in this study. As a case study, the datasets used in the study are collected by searching using three keywords: professor, prosecutor, and doctor in that these keywords contain rich public emotion and opinion. Advanced data collecting was conducted to select secondary keywords for data gathering. The secondary keywords for each keyword used to gather the data to be used in actual analysis are followed: Professor (sexual assault, misappropriation of research money, recruitment irregularities, polifessor), Doctor (Shin hae-chul sky hospital, drinking and plastic surgery, rebate) Prosecutor (lewd behavior, sponsor). The size of the text data is about to 100,000(Professor: 25720, Doctor: 35110, Prosecutor: 43225) and the data are gathered from news, blog, and twitter to reflect various level of public emotion into text data analysis. As a visualization method, Gephi (http://gephi.github.io) was used and every program used in text processing and analysis are java coding. The contributions of this study are as follows: First, different approaches for sentiment analysis are integrated to overcome the limitations of existing approaches. Secondly, finding Emotion Trigger can detect the hidden connections to public emotion which existing method cannot detect. Finally, the approach used in this study could be generalized regardless of types of text data. The limitation of this study is that it is hard to say the word extracted by Emotion Trigger processing has significantly causal relationship with emotional word in a sentence. The future study will be conducted to clarify the causal relationship between emotional words and the words extracted by Emotion Trigger by comparing with the relationships manually tagged. Furthermore, the text data used in Emotion Trigger are twitter, so the data have a number of distinct features which we did not deal with in this study. These features will be considered in further study.