원형수직터널의 시공시 지하수가 존재하는 경우 굴착에 의해 지하수의 흐름이 발생되어 추가적인 힘이 작용하게 된다. 원형수직터널의 지하수의 흐름은 일반적인 수평터널과 달리 깊이방향으로 다르게 작용되며, 수직터널의 벽체에 경사방향으로 작용하게 된다. 본 연구에서는 원형수직터널에 작용하는 침투력의 영향을 파악하기 위해 깊이에 따라 변하는 경사방향의 흐름성분을 수직과 수평방향으로 나누어 각각을 이론식에 적용하였다. 지하수가 영향을 미치는 범위는 토압을 야기하는 이완영역과 같은 것으로 가정하여 이론식을 유도하였다. 침투력에 의해 발생되는 추가적인 힘으로 인하여 원형수직터널의 이완영역에 작용되는 응력이 달라짐에 따라 침투력을 고려한 토압계수 산정식과 원형수직터널 벽체에 작용하는 응력 산정식을 본 연구를 통해 제안하였다. 가상지반을 설정하고 제안식을 적용한 결과, 침투를 고려하지 않은 건조한 지반에 비하여 수직방향응력은 약 1.4배, 토압은 2.5배 증가하는 결과를 보였다. 침투해석을 통하여 "유효응력+침투력"으로 구한 값과 제안식을 이용하여 산정한 값은 유사한 경향을 보여 제안식은 침투력을 적절히 고려하여 토압을 예측하는 것으로 나타났다.
발파설계가 터널 굴착 시 암반손상 및 여굴에 미치는 영향을 분석하고 암반손상 및 여굴이 터널 안정성에 미치는 영향을 분석함으로서 발파설계가 터널 지보설계에 미치는 영향을 연구하였다. 도로터널의 일반적인 발파패턴에 대해 동적발파 수치해석을 시행하고 연속체 손상역학(continuum damage mechanics)의 손상변수(damage variable)를 이용하여 여굴과 암반손상 정도를 분석함으로서 터널 굴착면 주위의 암반손상 정도와 영역을 구분하였다. 또한 발파하중 같은 동적하중이 암반내를 전파할 때 변화하는 암반의 동적파괴기준에 대한 연구를 수행하였다. 발파 암반손상 영향을 터널 안정성 해석에 반영하기 위하여 손상된 암반강성과 파괴기준을 적용하였다. 손상된 암반강성은 손상역학의 강도감소 모델을 이용하여 감소시켰다. 손상된 암반의 파괴기준은 암반강성과 지질강도지수의 관계식에서 도출한 손상된 지질강도지수(GSI$GSI_d$)를 적용함으로서 산출한 수정 Hoek-Brown 파괴기준을 적용하였다. 암반손상을 고려하여 터널안정성을 해석한 결과, 암반손상을 고려하지 않는 경우와 비교하여 소성영역 범위가 확대되고 변위량이 증가하였다. 이는 발파암반손상을 고려하지 않고 터널설계를 하는 경우 단기적 혹은 장기적으로 터널안정성이 위협받을 수 있음을 나타내었다.
본 논문은 4개의 철골모멘트 접합부에 대한 반복재하 실물대(實物大) 실험결과를 요약한 것이다. 주요 실험변수는 기둥과 보의 접합방식 (볼트접합 대 용접) 및 패널존의 강도 (강한 패널존 대 중간강도 패널존)이다. 중간 패널존 강도를 갖는 시험체는 패널존과 RBS 영역 모두에서 균형잡힌 방식으로 에너지가 소산되도록 고려하여 설계된 것으로 패널존 보강비용을 줄이고자 시도한 경우이다. 보웨브가 용접으로 접합된 경우의 시험체들은 특별연성모멘트골조에 요구되는 충분한 접합부 회전성능을 보여 주었지만, 웨브를 볼트로 접합한 시험체들은 스캘럽을 가로지르는 보플랜지의 조기 취성파괴로 인해 열등한 내진성능을 노출하였다. 보웨브를 볼트로 접합하면 비용을 줄일 수 있으나 원래 보단면의 전소성모멘트를 기둥에 전달하기 어려운 것으로 나타났다. 본 연구에서 적용된 것과 같이 양질의 용접시공에 의해 일단 그루브 용접부 자체의 취성파괴 문제가 해결되고 나면, 용접접근공내에 위한 보플랜지 모재의 파단이 다음의 문제로 대두됨을 알 수 있다. 용접접근공 내의 보 플랜지 파단문제를 역학적인 측면에서 이해하는데 도움이 되는 해석적 연구도 수행되었다.
The strain rate of reinforced concrete (RC) structures stimulated by earthquake action has been generally recognized as in the range from $10^{-4}/s$ to $10^{-1}/s$. Because both concrete and steel reinforcement are rate-sensitive materials, the RC beam-column joints are bound to behave differently under different strain rates. This paper describes an investigation of seismic behavior of RC beam-column joints which are subjected to large cyclic displacements on the beam ends with three loading velocities, i.e., 0.4 mm/s, 4 mm/s and 40 mm/s respectively. The levels of strain rate on the joint core region are correspondingly estimated to be $10^{-5}/s$, $10^{-4}/s$, and $10^{-2}/s$. It is aimed to better understand the effect of strain rates on seismic behavior of beam-column joints, such as the carrying capacity and failure modes as well as the energy dissipation. From the experiments, it is observed that with the increase of loading velocity or strain rate, damage in the joint core region decreases but damage in the plastic hinge regions of adjacent beams increases. The energy absorbed in the hysteresis loops under higher loading velocity is larger than that under quasi-static loading. It is also found that the yielding load of the joint is almost independent of the loading velocity, and there is a marginal increase of the ultimate carrying capacity when the loading velocity is increased for the ranges studied in this work. However, under higher loading velocity the residual carrying capacity after peak load drops more rapidly. Additionally, the axial compression ratio has little effect on the shear carrying capacity of the beam-column joints, but with the increase of loading velocity, the crack width of concrete in the joint zone becomes narrower. The shear carrying capacity of the joint at higher loading velocity is higher than that calculated with the quasi-static method proposed by the design code. When the dynamic strengths of materials, i.e., concrete and reinforcement, are directly substituted into the design model of current code, it tends to be insufficiently safe.
섭입 및 열개와 같이 대변형을 수반하는 지구동역학적 현상 발생은 암석권의 국지적인 약대의 발달이 필요하다. 이러한 약화 기작 중 하나인 전단열은 암석권의 온도를 국부적으로 높여 강도를 낮추는 역할을 하여 암석권 파괴를 촉진시킬 수 있다. 본 연구에서는 전단열에 대한 정량적인 분석을 위하여 2차원 탄소성 인장 분지 모형을 제작하여 기존 수치 모사 연구를 벤치마크하였다. 암석권의 항복강도, 인장 속도, 변형량- 및 온도-의존성 약화 현상 등을 조절하여 전단열 발생량에 미치는 영향을 분석하였다. 실험 결과, 약화를 고려하지 않은 경우 전단열의 발생량은 암석권의 항복강도 및 인장 속도와 양의 상관관계가 있는 것으로 나타났다. 기준 모형인 항복강도 100 MPa, 인장 속도 2 cm/yr로 설정된 경우, 총 20 km 인장된 시점(0.025의 변형률)에서 ~ 50 K의 온도 상승을 보여주었다. 소성 변형 및 온도에 따른 약화가 포함된 경우에는, 더 효율적인 약화 기작이 더 강한 전단열의 생성으로 이어지는데 이러한 현상은 약화 기작과 전단열 발생 사이에 양성되먹임이 작용함을 지시한다. 또한 변형 초기에 급격한 전단열 발생량을 보여주지만, 변형이 지속되어 암석권의 강도가 약화되면 전단열 발생 속도가 최대 ~ 80% 감소했다. 이는 약화 기작이 포함된 경우 전단열은 비교적 손상되지 않은 상태인 암석권의 강도에 큰 영향을 미침을 시사한다.
조선소, 교량 구조물, 건설기계, 플랜트 산업 등 다양한 분야에서 폭 넓게 활용되고 있는 이산화탄소 아크용접(FCAW: Flux Cored Arc Welding)은 피복 아크 용접(SMAW: Shielded Metal Arc Welding)의 단점을 보완하기 위한 대안으로 1950년대 초 개발되었다. FCAW는 모든 자세에서 용접이 가능하고 작업여건 변수가 많은 현장에서 우수한 품질을 얻을 수 있는 장점이 있어 탄소강과 합금강의 중판, 후판 용접에 많이 사용되고 있다. 본 연구에서는 FCAW를 이용하여 SS400(일반구조용 압연강재)와 SM490A(용접구조용 압연강재)를 이종용접한 후 용접부의 기계적 특성(인장시험, 굽힘시험, 경도시험, 충격시험, 매크로시험)을 분석하고 다음과 같은 결론을 도출하였다. 인장시험 결과, 모든 용접자세에서 KS 규격 인장강도 범위($400{\sim}510N/mm^2$)를 만족하였다. 굽힘시험 결과, 대부분의 시편에서 굽힘시 표면의 터짐 현상이나 기타 결점이 나타나지 않았고, 소성변형 후에도 충분한 인성을 발휘하는 것을 확인할 수 있었다. 경도시험 결과, 모든 결과 값이 KS B 0893의 규격치 350Hv보다 낮게 나타나 양호한 것으로 판단된다. 충격시험 결과, 모든 결과가 KS 기준 수치인 27J 보다 큰 것으로 나타났다. 매크로시험 결과 용접부의 형상별로 균일한 조직 상태를 나타냈으며, 용접부 전단면에 걸쳐 내부 결함, 기포 또는 불순물 등이 발견되지 않아 라미네이션의 우려가 없는 것으로 나타났다.
In eccentrically braced steel frames (EBFs), the links are fuse members which enter inelastic phase before other structure members and dissipate the seismic energy. Based on the force-based seismic design method, damages and plastic deformations are limited to the links, and the main structure members are required tremendous sizes to ensure elastic with limited or no damage. Force-based seismic design method is very common and is found in most design codes, it is unable to determine the inelastic response of the structure and the damages of the members. Nowadays, methods of seismic design are emphasizing more on performance-based seismic design concept to have a more realistic assessment of the inelastic response of the structure. Links use ordinary steel Q345 (the nominal yielding strength $f_y{\geq}345MPa$) while other members use high strength steel (Q460 $f_y{\geq}460MPa$ or Q690 $f_y{\geq}690MPa$) in eccentrically braced frames with high strength steel combination (HSS-EBFs). The application of high strength steels brings out many advantages, including higher safety ensured by higher strength in elastic state, better economy which results from the smaller member size and structural weight as well as the corresponding welding work, and most importantly, the application of high strength steel in seismic fortification zone, which is helpful to popularize the extensive use of high strength steel. In order to comparison seismic behavior between HSS-EBFs and ordinary EBFs, on the basis of experimental study, four structures with 5, 10, 15 and 20 stories were designed by PBSD method for HSS-EBFs and ordinary EBFs. Nonlinear static and dynamic analysis is applied to all designs. The loading capacity, lateral stiffness, ductility and story drifts and failure mode under rare earthquake of the designs are compared. Analyses results indicated that HSS-EBFs have similar loading capacity with ordinary EBFs while the lateral stiffness and ductility of HSS-EBFs is lower than that of EBFs. HSS-EBFs and ordinary EBFs designed by PBSD method have the similar failure mode and story drift distribution under rare earthquake, the steel weight of HSS-EBFs is 10%-15% lower than ordinary EBFs resulting in good economic efficiency.
As the intensity of urban underground space development increases, more and more tunnels are planned and constructed, and sometimes it is inevitable to encounter situations where tunnels have to underpass the river embankments. Most previous studies involved tunnels passing river embankments perpendicularly or with large intersection angle. In this study, a project case where two EPB shield tunnels with 8.82 m diameter run parallelly underneath a river embankment was reported. The parallel length is 380 m and tunnel were mainly buried in the moderate / slightly weathered clastic rock layer. The field monitoring result was presented and discussed. Three-dimensional back-analysis were then carried out to gain a better understanding the interaction mechanisms between shield tunnel and embankment and further to predict the ultimate settlement of embankment due to twin-tunnel excavation. Parametrical studies considering effect of tunnel face pressure, tail grouting pressure and volume loss were also conducted. The measured embankment settlement after the single tunnel excavation was 4.53 mm ~ 7.43 mm. Neither new crack on the pavement or cavity under the roadbed was observed. It is found that the more degree of weathering of the rock around the tunnel, the greater the embankment settlement and wider the settlement trough. Besides, the latter tunnel excavation might cause larger deformation than the former tunnel excavation if the mobilized plastic zone overlapped. With given geometry and stratigraphic condition in this study, the safety or serviceability of the river embankment would hardly be affected since the ultimate settlement of the embankment after the twin-tunnel excavation is within the allowable limit. Reasonable tunnel face pressure and tail grouting pressure can to some extent suppress the settlement of the embankment. The recommended tunnel face pressure and tail grouting pressure are 300 kPa and 550 kPa in this study, respectively. However, the volume loss plays the crucial role in the tunnel-embankment interaction. Controlling and compensating the tunneling induced volume loss is the most effective measure for river embankment protection. Additionally, reinforcing the embankment with cement mixing pile in advance is an alternative option in case the predicted settlement exceeds allowable limit.
본 연구에서는 휴·폐광산 채굴 공동을 다른 목적으로 사용코자 할 경우, 특히 갱도 내에서 발생하는 반복 교통 진동이 채굴 공동의 장기적인 안정성에 미치는 영향을 분석하였다. 연구 대상 광산은 주방식 채광법이 적용된 지하 석회석 광산이며, 해당 광산이 물류 창고로 활용되는 상황을 가정하여 동적 수치해석을 수행하였다. 특히 해당 광산에서 광산차량의 운행으로 실제 발생하는 교통진동을 직접 측정하여 이를 진동파형 형태로 동적수치해석용 입력자료로 반영하였다. 20,000회의 교통 진동이 반복된 상황을 고려한 동적수치해석 이후, 채굴 공동은 안정적인 것으로 분석되었지만, 해석 단면 전체에 걸쳐 최대주응력의 증가와 탄소성 거동 영역의 추가 발생이 확인되었다. 또한 채굴 공동 벽면의 변위와 체적 변형률, 최대주응력의 변화 양상에서 반복 교통 진동이 지속될 경우, 공동 주변의 응력 변화로 인해 공동의 불안정성이 증대될 수 있음을 확인하였다. 채굴 공동에 작용하는 교통 진동의 영향을 분석한 국내 연구 사례가 부족한 상황에서 본 연구는 국내 휴·폐광산 활용을 위한 기초연구자료로 활용될 것을 기대한다.
도심지 등 지역적인 여전에 의하여 기존의 지하 공동 또는 터널에 근접하여 발파를 이용한 새로운 터널을 굴착할 경우, 새로운 터널의 굴착으로 인하여 지반이 이완되고 따라서 기존 지하 공동의 안정성에 문제가 발생할 수 있다. 이러한 가존 지하 공동의 안정성에 문제를 발생시킬 수 있는 가장 큰 요소로는 기존 지하 공동과 신설 터널의 이격거리가 될 수 또한 신설 터널 굴착으로 인한 소성영역의 발생에 따른 지반 이완을 문제 심을 수 있다. 따라서 본 연구에서는 기존 광역 상수관과 신설 터널의 이격거리에 따른 기존 광역 상수관의 안정성을 평가하기 위하여 이격거라가 다른 여섯 가지 모델에 대해 석고를 이용힌 2차원 축소 모형실험을 실시하였다. 실험 결과는 터널 굴착과정과 파괴 단계에서 발생된 변위 벡터와 균열양상으로 표현하였다. 터널 굴착과정 중 발생하는 변위를 분석하면, 터널과 광역 상수관의 간격이 상수관 직경의 2.5배 (2.5D)까지는 이격거리가 증가함에 따라 감소하는 경향을 보인다. 그러나 중심 간격이 2.5D를 넘으면 추가변위는 발생하지 않았다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.