• Steel and Composite Structures
• /
• 제1권1호
• /
• pp.131-144
• /
• 2001

Overpressurization can occur due to the ignition of flammable vapors existing inside aboveground oil storage tanks. Such accidents could happen more frequently than other types of accident. In the tank design, when the internal pressure increases, the sidewall-to-roof joint is expected to fail before failure occurs in the sidewall-to-bottom joint. This design concept is the socalled "frangible roof joint" introduced in API Standard 650. The major failure mode is bifurcation buckling in this case. This paper presents the bifurcation buckling pressures in both joints under internal pressure. Elastic and elastic-plastic axisymmetric shell finite element analysis was performed involving large deformation in the prebuckling state. Results show that API Standard 650 does not evaluate the frangible roof joint design conservatively in small diameter tanks.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 가을 학술발표회 논문집
• /
• pp.466-472
• /
• 1996

The nonlinear analysis was perforned for a 2-bay 2-story moment-resisting reinforced concrete plane frame with seismic detail using KDARC 2D program. The analytical models consist of the material model, the member model, the hysteretic model, and the damage model etc. The conclusion based on the results of analysis is as following. : (1) Story shear-displacement relationship is similar to the experiment result but from the energy point of view, the analysis relationship is similar to the experiment result but from the energy point of view, the analysis result was different from the experiment result. (2) Plastic hinges were found to occur mainly in beams at first story while all the columns had plastic hinges throughout the structure. (3) Failure mode is a little different from experiment result in the yielding mechanism. (4) Damage index isabout 0.25. This means that the degree of damage is moderate and can be repairable.

• Structural Engineering and Mechanics
• /
• 제55권5호
• /
• pp.913-929
• /
• 2015

The ratcheting and strain cyclic behaviour of joined conical-cylindrical shells under uniaxial strain controlled, uniaxial and multiaxial stress controlled cyclic loading are investigated in the paper. The elasto-plastic deformation of the structure is simulated using Chaboche non-linear kinematic hardening model in finite element package ANSYS 13.0. The stress-strain response near the joint of conical and cylindrical shell portions is discussed in detail. The effects of strain amplitude, mean stress, stress amplitude and temperature on ratcheting are investigated. Under strain symmetric cycling, the stress amplitude increases with the increase in imposed strain amplitude. Under imposed uniaxial/multiaxial stress cycling, ratcheting strain increases with the increasing mean/amplitude values of stress and temperature. The abrupt change in geometry at the joint results in local plastic deformation inducing large strain variations in the vicinity of the joint. The forcing frequency corresponding to peak axial ratcheting strain amplitude is significantly smaller than the frequency of first linear elastic axial vibration mode. The strains predicted from quasi static analysis are significantly smaller as compared to the peak strains from dynamic analysis.

• 센서학회지
• /
• 제15권4호
• /
• pp.297-301
• /
• 2006

We have fabricated a multi-mode nonlinear plastic optical fiber (POF) using organic nonlinear optical materials and demonstrated the propagation of light. The refractive indices of core and cladding are 1.5240 and 1.5172. We made a POF preform by rod-in tube method. The core diameter of the fabricated POF is about $30{\mu}m$. We evaluated the temperature characteristics of POF. The sensitivity is $0.345{\;}mW/^{\circ}C$ and the linearity of sensor was good.

• Journal of Mechanical Science and Technology
• /
• 제20권2호
• /
• pp.197-204
• /
• 2006

The purpose of this study is to evaluate the AE characteristics for the basemetal, PWHT (post-weld heat treatment) and weldment specimens of SA-516 steel during fracture testing. Four-point bending and AE tests were conducted simultaneously. AE signals were emitted in the process of plastic deformation. AE signal strength and amplitude of the weldment was the strongest, followed by PWHT specimen and basemetal. More AE signals were emitted from the weldment samples because of the oxides, and discontinuous mechanical properties. AE signal strength and amplitude for the basemetal or PWHT specimen decreased remarkably compared to the weldment because of lower strength. Pre-cracked specimens emitted even lower event counts than the corresponding blunt notched specimens. Dimple fracture from void coalescence mechanism is associated with low-level AE signal strength for the basemetal or PWHT. Tearing mode and dimple formation were shown on the fracture surfaces of the weldment, but only a small fraction produced detectable AE.

• Earthquakes and Structures
• /
• 제20권2호
• /
• pp.225-238
• /
• 2021

Supplemental passive dampers are widely employed to improve the structural performance of buildings under seismic excitations. Nevertheless, the added damping could be counter-productive if the axial forces induced by the damper reaction forces are not routed properly in the columns. A few researchers engaged to optimize the width-wise damper arrangement to improve the delivered path of the axial column forces. However, most of these studies are limited under the design-based seismic level and few of them has evaluated the collapse performance of buildings under strong earthquakes. In this paper, the strategic width-wise placement method of viscous dampers is explored regarding the building performance under collapse state. Two realistic steel buildings with different storeys are modelled and compared to explore higher mode effects. Each building is designed with four different damper arrangement scenarios based on a classic damper distribution method. Both a far-fault and a near-fault seismic environment are considered for the buildings. Incremental Dynamic Analysis (IDA) is performed to evaluate the probability of collapse and the plastic mechanism of the retrofitted steel buildings.

• 소성∙가공
• /
• 제31권2호
• /
• pp.64-72
• /
• 2022

Since aluminum alloys experience both tensile and compression deformation modes during forming process, it is important to understand the role of deformation mode on the hot formability of metallic alloys. In the present work, the hot formability of Al7050 alloy was investigated by conducting both tensile and Gleeble tests at various temperatures and strain rates. Processing maps representing low efficiency regions were observed at low temperature and high strain rate in both tensile and compressive deformation modes while the maximum efficiency regions depended on different deformation modes. Moreover, samples tested at stable processing conditions presented a smaller pore fraction than those at instable conditions that resulted in crack initiation during plastic deformation. This result shows that different deformation modes during plastic forming can affect formability changes of metallic alloys. Understanding of tension-compression behaviors will help us solve this problem.

• 한국강구조학회 논문집
• /
• 제23권1호
• /
• pp.41-49
• /
• 2011

폭이 8m이상인 광폭형 비닐하우스는 농기구 사용의 편리성과 토지 활용성 등의 장점이 부각되면서 농가에 점차 보급되고 있는 실정이다. 이 논문은 광폭형 비닐하우스의 인장타이보강에 따른 효과에 관한 실험결과를 제공한다. 이미 앞선 연구에서는 농촌진흥청에서 고시된 폭이 6.5m인 단동형 비닐하우스 모델을 선정하여 인장타이보강효과에 대한 실험을 수행한바 있다. 본 연구에서는 ${\phi}48.1{\times}2.1$ 단면, 폭이 10.2m인 광폭형 비닐하우스를 선정하여 대칭하중 가력실험과, 햇빛에 의한 열이나 바람에 의한 불균형 적설하중을 산정한 편심하중 가력실험을 수행하였다. 타이를 보강하지 않은 실험체와 인장타이를 보강한 실험체의 하중-변위 관계를 비교 분석하였다. 대칭하중 가력실험에서 인장타이로 보강되어진 모델은 내력이 68~93%정도 증가하였다. 파괴모드는 무보강시에는 sway붕괴 메카니즘이 일어났으나 타이 보강시에는 아치 좌굴 메카니즘이 일어났다. 편심하중 가력실험 결과 타이로 보강하였을 경우 내력이 10~20%정도 증가하였다. 파괴모드는 무보강시에는 조합 붕괴 메카니즘이 일어났지만 타이보강시에는 아치 좌굴 메카니즘이 일어났다.

• 한국지반신소재학회논문집
• /
• 제7권3호
• /
• pp.9-16
• /
• 2008

본 논문에서는 보강토 옹벽의 파괴거동을 탄소성이론에 의한 수치해석적으로 평가에 관한 연구내용을 다루었다. 우선, 보강토 옹벽의 기본적인 파괴거동에 대하여 검토하였다. 유한요소법을 사용하여 보강토 옹벽의 파괴거동에 영향을 미치는 주요 요인에 대하여 매개변수연구를 실시하였다. 주 검토목적으로는 보강토 옹벽의 파괴형상에 미치는 요인 및 영향에 대하여 분석하는 것이다. 뒤채움흙의 마찰각, 보강재 종류, 보강재 길이에 따른 파괴거동에 미치는 영향에 대하여 수치해석적 분석을 하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권5호
• /
• pp.1140-1147
• /
• 2001

This paper describes the effect of various molding pressure for Mode I. Mode II interlaminar fracture toughness of carbon fiber reinforced plastic composites by using double cantilever beam(DCB), end notched flexure(ENF) and end loaded split(ELS) Specimen. The value of $G_{IC}$, $G_{IIC}$ as a function of various molding pressure is almost same at 307, 431, 585 kPa, however it shows highest value under 307kPa molding pressure, The SEM photographs show good fiber distribution and interfacial bonding of composites when the molding pressure is the 307kPa.