• 한국분말재료학회지
• /
• 제9권3호
• /
• pp.148-152
• /
• 2002

The microstructures and indentation fracture of pressureless-sintered $DyNbO_4$ crystalline were investigated as a basic study for the application of weak phase of fibrous monolithic composites. They were comprised with many lamella twins as well as micro-cracks at the grain boundaries. The hardness at room temperature was remarkably low value(575 Hv) due to the low relative density and existence of microcracks at grain boundaries. The main fracture mode was a typical intergranular fracture, and showed remarkable micro-cracking effect. The heavy plastic deformation was observed around the site of indentation. In addition, the $DyNbO_4$ was expected to apply as a weak phase in the fibrous monolithic composites because of the low hardness and easily plastic deformation that could be led the preferable pulled-out and microcracking toughening under the failure.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.73-77
• /
• 2004

Failure predictions of composite single-lap bonded joints were performed considering both of composite adherend failure and bondline failure. An elastic-perfectly plastic model of adhesive and a delamination failure criterion are used. The failure prediction results such as failure mode and strength have very good agreements with the test results of joint specimens with various bonding methods and parameters. The influence of variations in the effective strength (that is, adhesion performance) and plastic behavior of adhesive on the failure characteristics of composite bonded joints are investigated numerically. The numerical results show that optimal joint strength is archived when adhesive and delamination failure occur in the same time.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.710-715
• /
• 1997

This paper deals with the analysis of the optimum value of honeycomb core considering variable design parameter. As thickness and height of core rises in design parameter, natural frequency of laminated composite plate increases. The angle-phy has the maximum value when the plate of honeycomb core join to opposite direction. This paper shows that the natural frequency of CFRP was higher than that of GFRP and mode shapes were various at angle-ply.

• 대한기계학회논문집A
• /
• 제32권9호
• /
• pp.782-787
• /
• 2008

First, the effect of the geometry such as the curved shape of the struts composing the truss structure of WBK is elaborated. Then, analytic solutions for the material properties of WBK and the maximum loads of a WBK-cored sandwich panel under bending are derived. A design optimization with the face sheet thickness and the core height selected as the design variables is presented for given slenderness ratios of the WBK core. Unless the face sheet thickness is limited, the optimal design to give the maximum load per weight is always found at a confluence of three failure modes, namely, face sheet yielding, indentation plastic, and core shear modeB plastic.

• 한국지진공학회논문집
• /
• 제5권3호
• /
• pp.57-64
• /
• 2001

보강된 판 및 쉘구조의 동적 비선형해석을 수행하기 위하여, 유한회전을 고려한 변형된 쉘유한요소를 이용하여 total Lagrangian formulation이 제시된다. 전단구속 (shear locking) 현상과 가상의 제로에너지 모우드를 동시에 제거하기 위하여 가정변형도 개념을 채용한다. 탄소성해석에서는 return mapping 미해rithm이 쉘구조의 붕괴 해석에 적용된다. Newmark 직접적분법을 사용하여 동하중 및 지진하중을 받는 쉘구조의 동적 비선형해석 결과를 제시한다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1298-1302
• /
• 2000

Electrorheological(HER) and magnetorheologica(MR) fluids have a unique ability to increase the dynamic yield stress of the fluid substantially when electric or magnetic field is applied. ER and MR fluid-based dampers are typically analyzed using Bingham-plastic shear flow analysis under Quasi-steady fully developed flow conditions. An alternative perspective, supported by measurements reported in the literature, is to allow for post-yield shear thinning and shear thickening. To model these, the constant post-yield plastic viscosity in Bingham model can be replaced with a power-law model dependent on shear strain rate that is known as the Herschel-Bulkley fluid model. The objective of this paper is to predict the damping forces analytically in a typical ER bypass damper for variable electric field, or yield stress using Herschel-Bulkley analysis.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.116-119
• /
• 1999

The effects of secondary phase morphology and carbon content on the plastic deformation of 0.2C-1.5Si-1.5mn TRIP(TRansformed Induced Plasticity) steel have been investigated at various annealing and bainitic transformation temperatures. The morphology of ferrite and secondary phases was controlled by the annealing temperature and the distribution of secondary phase was controlled by the bainitic transformation temperature. The secondary phase contributed to elongation and/or UTS depending on the ferrite morphology which determined deformation mode simple elongation or rotation of secondary phase along the tensile direction In case of the sample containing the granular type retained austenite the elongation was improved as carbon stabilized the austenite phase. If the film-shape retained austenite in acicular ferrite was dominant however UTS was enhanced as the transformed martensite was hardened by carbon.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.751-756
• /
• 2000

The structural behavior of reinforced concrete slabs strengthened by glass fiber reinforced plastic-panels experimentally investigated. The experimental variables are strengthening length, strengthening width, and pre-crack existence. The pre-cracked slabs are initially loaded to 70 percent of ultimate flexural capacity and subsequently repaired with GFRP-Panels bonded to the tension face of the slabs. Five one-way slabs were tested to failure. The main failure mode of strengthened slabs is separation failure by crack propagation from load point section to end of plate. The behavior of strengthened slabs is represented by a maximum load, load-deflection curves an load-strain curves.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.291-292
• /
• 2005

Comparing with conventional STN-LCD, a good electro-optical characteristics were observed on the STN-LCDs of low cell gap using liquid crystals that have large refractive indices. Especially, A stable voltage-transmittance(V-T) curve of the plastic STN-LCD was measured and fast response time characteristics were obtained. We suggested that fast response STN-LCD is promising technique in the flexible display of small size because it has lots of advantages such as low cost, simple manufacture process comparing with other modes.

• 한국농공학회논문집
• /
• 제46권2호
• /
• pp.67-75
• /
• 2004

This study aims to investigate the dynamic behaviour of a parabolic arch with initial deflection by using the elasto-plastic finite element model where the von-Mises yield criteria have been adopted. The initial deflection of arch was assumed by the high order polynomial of ${\omega}_i$ = ${\omega}_o$${(1-{(2x/L)}^m)}^n$) and the sinusoidal profile of ${\omega}_i$ = ${\omega}_o$$\sin$(n$\pi$x/L). Several numerical examples were tested considering symmetric initial deflection modes when the maximum initial deflection of an arch is fixed as L/500, L/1000, L/2000 or L/5000. The effects of polynomials order on the dynamic behavior of arch were not conspicuous. The most unfavorite dynamic response occurs when the maximum initial deflection varies from L/1000 to L/4000 if the initial deflection mode is represented by high order polynomials.