• 대한기계학회논문집A
• /
• 제20권6호
• /
• pp.1798-1809
• /
• 1996

The purpose of this paper is to develop new Z-Factors to evaluate the behavior of circumferential surface crack in ferritic steel piping including base metal and Submerged Arc Weld(SAW) metal in nuclear power plant. The Z-factor is a load multiplier to convert plastic load to elasto-plastic load. However the current Z-Factor is a load multiplier to convert plastic load to elasto-plastic load. However the current Z-Factor gives too conservative results. In this study, a J-estimation method, SC.TNP method, which is based on GE/EPRI expression, is used to develop new Z-Factors. The desirabilities of both the SC.TNP mehtod and the new Z-Factors are examined using the previous experimental results for the circumferential surface crack in ferritic steel pippings. The results are as follows ; (1) The SC.TNP mehtod is good for describing the circumferential surface crack behavior in farritic steel pipings, while the well-known R6 mehtod and DPFAD method give too conservative results. (2) The ASME-Z-Factor method using nwe Z-Factors well predicts the behavior of circumferential surface crack in ferritic steel pipings including base emtal and SAW metal.

• Structural Engineering and Mechanics
• /
• 제13권1호
• /
• pp.35-52
• /
• 2002

It was shown in the previous study (Lee and Bertero 1993) that incremental collapse can lead to the exhaustion of the plastic rotation capacity at critical regions in a structure when subjected to the number of load cycles and load intensities as expected during maximum credible earthquakes and that this type of collapse can be predicted using the shakedown analysis technique. In this study, a minimum-weight design methodology, which takes into account not only the prevention of this incremental collapse but also the requirements of the serviceability limit states, is proposed by using the shakedown analysis technique and a nonlinear programming algorithm (gradient projection method).

• 대한기계학회논문집A
• /
• 제34권11호
• /
• pp.1675-1680
• /
• 2010

캐나다형 중수로에서 피더관은 가동 중에 유동 가속 부식에 의해 감육이 발생한다. 피더관에 감육이 발생하면 배관 건전성이 떨어진다. 본 논문은 원형 감육이 발생한 피더관에서의 기기신뢰성 평가를 위한 한계 하중을 연구하였다. 유한요소 해석을 통하여 면내 굽힘 하중과 내압을 받는 경우에 대하여 연구하였다. 재료는 대변형 효과를 고려하고 탄성-완전소성 재료로 가정하였다. 원형 감육이 발생한 피더관에 대하여 내압과 닫힘 방향, 열림 방향 굽힘 하중에 대하여 한계하중해를 제시하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 추계학술대회논문집
• /
• pp.57-68
• /
• 1995

A design methodology is applied for manufacturing the valve-spring retainer component. The design criterion is the forging load within the available press limit. Also, the final product should not have any geometrical defect. The rigid-plastic TEM has been applied to simulate the conventional five-stage manufacturing processes, which include mainly backward extrusion and heading process. Simulations of one step process from selected stocks to the final product shape are performed for a possibly better process than the conventional one.

• 콘크리트학회논문집
• /
• 제23권6호
• /
• pp.731-740
• /
• 2011

KCI 2007, ACI 318-08에 제시된 모멘트재분배 방법은 등분포 중력하중을 받는 연속 휨재에 대하여 검증된 방법이다. 횡하중에 의한 모멘트재분배 및 비탄성 거동은 중력하중과 전혀 다른 메커니즘을 발생된다. 이 연구에서는 기초역학에 근거하여 중력하중과 횡하중을 받는 철근콘크리트 모멘트골조의 보에 발생되는 모멘트재분배와 소성변형의 관계를 정량화하고, 이로부터 보의 소성변형능력에 근거한 모멘트재분배 설계법을 제안하였다. 제안된 모멘트재분배비는 KCI 2007, ACI 318-08 등 기존 설계기준과 마찬가지로 극한한계상태의 단면해석으로 결정되는 철근의 인장변형률로 정의된다. 또한 모멘트재분배비는 경간, 철근비, 단면강성, 변형경화 거동에 의하여 영향을 받는다. 제안된 방법을 사용하여 탄성해석으로 구한 설계모멘트를 재분배시키는 설계 가이드라인 및 예제를 제시하였다.

• 전산구조공학
• /
• 제7권4호
• /
• pp.113-118
• /
• 1994

본 연구의 목적은 표준파괴인장시험편에 대한 탄소성유한요소해석이다. 탄소성파괴역학의 이론과 수치해석을 위한 조건들이 기술되고 균열선단의 특이성을 모형화하기 위한 가능성이 논의된다. 표준파괴인장시험편의 탄소성유한요소해석으로부터 J적분이나 균열개구변위(COD)와 같은 파괴역학계수들과 그들의 상관관계가 계산되고 소성역의 크기와 형태가 구해진다. 실험과 계산결과들이 비교되고 한계하중의 계산이 논의된다.

• 한국농공학회지
• /
• 제30권2호
• /
• pp.55-66
• /
• 1988

This study was conducted to investigate the various engineering properties and correlationshops among the soil constants of alluvial clayey deposits distributed in the bay of Asan and their results are summarized as follows : 1. Grain size distribution of soil was consisted of 12 % of clay, 46-73 % of silt, 2-23 % of sand, and as for the consistency characteristics, 26-36 % of liquid limit, 18-21 % of plastic limit and 6-16 % of plastic index, and so the soil belonging to as a lower plastic nonorganic clay, it's specific gravity was 2,66-2.70, and the location on the plastic chart was approximately above the A-line. Z The natural moisture content and unit weight were 30-43 % and 1.76-1.87 g I cm$_3$, respectively, and according to increment of natural moisture content, the unit weight was decreased, and the initial void ratio and degree of saturation were shown of 0,87-1119 and 92- 100 %, most of saturated. 3. Cone resistance value which was shown 2.4 - 6.5 kg / $cm^2$ was a little lower and it was increased with the depth of layer and shown the formular $q_c=0.7_z+1.32$. 4. Unconfined compression strength was about 0.18-0.43kg /$cm^2$, cu, 0.1-0.22kg / $\psi$, $2-6^{\circ}$ under uu-test condition of triaxial, and CCU, 0.08-0.3 kg/cm , $\psi$, $12-18^{\circ}$ under the condition of cu-test. 5. Pre-consolidation load of characteristics of consolidation was 0.4-0.8 kg / $cm^2$, compression index, about 0.17-0.33. 6. Liquid limit and plastic index were incresased with the increment of clay content but most of alluvial clay was appeared as a normal through non-activity clay soil shown more natural moisture content than liquid limit, and their relationship as follows : LL=0.38( cy+54.8), PI=0.836(LL -17.8), PI =0.468(LL -0.48) 7. The initial void ratio presented correlationship of positive among clay content, natural moisture content and liquid limit, and that of reverse with unit weight, and their results as follws : $e_o=0.024(w_n+0.2)$, $e_o=e_o=0.0003c_y+0.0005 LL+0.0151 W_n+\frac{3.58}{r-t}-1.52$ 8. It was shown that the compression index has correlationship of postive among the clay content, liquid limit, plastic index, natural moisture content and initial void ratio, and their relationships as follows ; $c_c=0.44(e_o-0.47)$, $c_c=0.001$

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 추계학술대회 논문집
• /
• pp.107-117
• /
• 1994

A design methodology is applied for manufacturing a disk-brake piston component and a washing machine container. The design criteria are the limit drawing ratio and the forging load within the available press limit. Also, the final product should not have any geometrical defect. The rigid-plastic and elastic-plastic FEM have been applied to simulate both of the conventional manufacturing processes, respectively, which include deep drawing and forging process. Simulations of one stage process from a selected stock to the final product shape are performed for generating information on additional requirements for metal flow. The best manufacturing processes are selected, which is using a hemispherical punch in the deep drawing process for both disk-brake piston component and washing machine container.

• 소성∙가공
• /
• 제3권2호
• /
• pp.178-188
• /
• 1994

A design methodology is applied for manufacturing a disk-brake piston component. The design criteria are the limit drawing ratio and the forging load within the available press limit. Also, the final product should not have any geometrical defect. The rigid-plastic FEM has been applied to simulate the conventional four stage manufacturing processes, which include deep drawing and forging process. Simulation of one stage process from a selected stock to the final product shape is performed for generating information on additional requirements for metal flow. Two stage forming processes with different punch corner and nose geometries are also simulated to identify the possible best solutions. Finally, the best manufacturing process is selected, which is using a hemispherical punch int he deep drawing process.

• 대한기계학회논문집A
• /
• 제37권11호
• /
• pp.1379-1386
• /
• 2013

본 논문에서는 용접부 중앙에 원주방향 관통균열이 있는 V-그루브 맞대기 용접 배관의 한계하중 해석을 수행하였다. V-그루브 맞대기 용접 배관이 그루브 각 $45^{\circ}$, $90^{\circ}$를 갖는 형상에 대한 한계하중 식을 제시하기 위해 용접 형상의 변화에 따른 용접부 너비를 정의하였고 강도불일치 비, 용접부 너비, 균열 길이 및 배관 반경 비에 대한 체계적인 변수 해석을 수행 하였다. 모재와 용접재는 탄성 완전소성재료로 가정하였으며 상불일치와 하불일치 조건에서의 인장 하중과 굽힘 하중에 대한 강도불일치 한계하중이 강도불일치 비($M_F$)와 형상변수(${\psi}$)를 통해 정량화 됨을 유한요소 해석을 통해 확인하였다.