• 한국안전학회지
• /
• 제30권5호
• /
• pp.108-113
• /
• 2015

Plastic injection moulding machine is widely used for many industrial field. It is classified into mandatory safety certification machinery in Industrial Safety and Health Act because of its high hazard. In order to prevent industrial accidents by plastic injection moulding machine, it is necessary for designer to identify hazardous factors and assess the failure modes to mitigate them. This study tabulates the failure modes of main parts of plastic injection moulding machine and how their failure has affect on the machine being considered. Failure Mode & Effect Analysis(FMEA) method has been used to assess the hazard on plastic injection moulding machine. Risk and risk priority number(RPN) has been calculated in order to estimate the hazard of failures using severity, probability and detection. Accidents caused by plastic injection moulding machine is compared with the RPN which was estimated by main regions such as injection unit, clamping unit, hydraulic and system units to find out the most dangerous region. As the results, the order of RPN is injection unit, clamping unit, hydraulic unit and system units. Barrel is the most dangerous part in the plastic injection moulding machine.

• 소성∙가공
• /
• 제12권8호
• /
• pp.738-743
• /
• 2003

The major problems of a plastic injection mould can be devided into two kinds, one is in mould another in injected parts. Most of defects of the former comes from mould design, such as, structure and working. The latter are weld line, warpage, sink mark, burning, flow mark, scratching, shading, black hole and so on. Most of problems in injection molding are difficult to find the reason because of complexity. The purpose of this paper is to improve the quality of plastic injection mould and parts with inquiring the counter plan and analizing troubles of the part of Flat TV Front Cover by flow control method and gas-assisted injection moulding. For minimizing defects of the injection moulded parts, computer aided simulation method for injection mould filling was used. Based on these numerical results, the guidelines of mould design and injection processing condition were established. As a result, the improvement of quality, such as minimizing surface defects of injection moulding parts and troubles in mould was achieved.

• Design & Manufacturing
• /
• 제9권2호
• /
• pp.10-15
• /
• 2015

The water has been the suitable for the cooling medium until now. But the water as cooling medium seem to have the limit for high speed injection. The steam plastic molding injection use the steam as the medium when raise the mold temperature. The weld line has been the major quality problems in a plastic injection parts to be difficult to be solved. These problems in injection-molded plastic parts are difficult to find the reason because these issues are usually in tradeoff realtions with each other. The purpose of this paper is to obtain the optimum injection moulding condition for improving the quality of plastic injection parts and to inquire the productivity improvement with the measured cycle time by steam plastic moluding injection. Based on these numerical results, the guidelines of mould design and injection processing condition were established. As a result, the improvement of quality and the reduction of cycle time was achieved.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.201-206
• /
• 2003

Plastic injection mould have two kinds of trouble, one is in mould another in injection parts. Most of defects of the former take the cause in a design like in structure and working, the later weld line, transforming, sink mark, burning, flow mark, scratching, shading, black hole and so on. Most of problems of the later is difficult for making a clear definitely the reason of defects because of complexible. The purpose of this paper is to improve the quality of plastic injection mould and parts with inquiring the counter plan and rouble of the part of Flat TV Front Cover by flow control method and gas- assisted injection moulding. For minimizing defects from injection moulding parts, this paper was investigated with using computer aided injection mold filling simulations. Based on these numerical results, I established guidelines mould design and injection processing condition. As a results I got the improve of quality, minimizing surface defects moulded parts and troubles in mould.

• 대한기계학회논문집A
• /
• 제34권10호
• /
• pp.1487-1492
• /
• 2010

본 논문의 목적은 3 차원 사출성형해석을 통한 냉장고 플라스틱 서랍 제작용 사출성형 금형의 형상적응형 냉각수로 설계이다. 바람직한 형상적응형 냉각수로의 설계를 얻기 위하여 형상적응형 냉각수로의 직경과 위치가 사출성형 특성과 제품의 품질에 미치는 영향을 정량적으로 고찰하였다. 해석결과로부터 제품의 균일 냉각과 변형 최소화가 가능한 최적의 형상적응형 냉각수로의 설계를 도출할 수 있었다. 본 연구에서 제안된 사출성형 금형과 기존의 직선형 냉각수로의 사출성형 금형을 냉각/제품 제작 시간 및 제품 품질 측면에서 비교한 결과, 형상적응형 냉각수로를 가진 사출성형 금형이 제품의 생산성과 품질을 동시에 향상시킬 수 있음을 알 수 있었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.399-400
• /
• 2006

M390 microclean(R) of $B{\ddot{o}}hler$ Edelstahl is a powder metallurgical plastic mould steel with a high level of corrosion and wear resistance and therefore often used in the plastics processing industry. But as a consequence of rapidly advancing developments in the plastics processing industry the required level of wear resistance of tool steels in this field is constantly rising. For that reason a new PM tool steel with higher hardness values and an increased amount of primary carbides has been developed to improve the resistance against abrasive and adhesive wear. The wear resistance of both steels against adhesive situations for components of the plastification unit of injection moulding machines has been tested with a novel method. In case of processing polyolefins with an injection moulding machine it was found that there is adhesive wear between the check-ring and the flights of the screw tip of the non-return valve under certain circumstances. The temperature in that region was measured with an infrared temperature sensor. The existence of significant peaks of that signal was used as an indicator for an adhesive wear situation.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권5호
• /
• pp.440-446
• /
• 1997

This research has been performed for the fabrication of high quality ferrite plastic magnet. The magnetic properties of S $r_{5.9}$F $e_2$ $O_3$ ferrite bonded magnets by injection moulding with a variety of applied magnetic field were investigated. 0.3wt% CaCO3, 0.2wt% $SiO_2$, 0.5wt% $Al_2$ $O_3$and 0.5wt% N $a_2$ $SiO_3$are added in order to improve the magnetic properties of Sr-ferrite plastic magnets during the powder fabrication. For carbon coating on chemical compound specimen, 5wt% polyvinyl alcohol is added, and then calcinated under $N_2$ environment of 12$25^{\circ}C$. The particle size is distributed from 0.9~1.2${\mu}{\textrm}{m}$ which approximates to the single domain. The obtained Sr ferrite powder is well mixed with silane coupling and calcium stearate of 1wt%. Nest, the specimen is pelleted after kneading each of them with polyamidel2 as a binder. When the temperature of injection and mould were 25$0^{\circ}C$ and 8$0^{\circ}C$ respectively at injection pressure of 200kgf/$\textrm{cm}^2$, the degree of orientation was 85.3% under the applied magnetic field of 12kOe. As the results, when the packing density of Sr ferrite powder was 90wt%, the magnetic properties of Sr ferrite bonded magnet were follows : $_{B}$ $H_{c}$=2.41kOe, Br=3.1kG, (BH)$_{max}$=2.21MgOe. Especially, the Sr-ferrite bonded magnet with 10wt% N $d_2$F $e_{14}$B additive were as follows : $_{B}$ $H_{c}$=2.57kOe, Br=3.14kG and (BH)$_{max}$=2.39MGOe.GOe.GOe.GOe.e.

• 한국공작기계학회논문집
• /
• 제11권6호
• /
• pp.68-74
• /
• 2002

This research covers the development of axi-symmetric plastic elements for injection molding with insert steel such as high stiffness Sabot. The functional requirements of sabot are concentricity and fracture resistance about vertical and horizontal forces. For these, an analysis of characteristics of PEI(polyetherimide) polymer is performed by standard test specimen with accordance of ASTM test guidance. Moldflow analysis and simulation of injection molding process are carried out in order not only to estimate of the warpage but also to predict the characteristics of residual stresses which both product and structure of mold may have. A new vertical side injection machine and transverse mold have been constructed. Results of the measuring concentricity and fracture test after molding of sabot are satisfied to design specification over Cp $ratio{\geq}1.33$. Finally, this technique needs more research application to others axi-symmetric elements having different radius with insert steel md structure analysis from now on.

• Design & Manufacturing
• /
• 제12권2호
• /
• pp.22-26
• /
• 2018

In the automotive industry these days, plastic parts have been developed and replaced with plastic parts by maintaining the same function of existing press parts for a variety of reasons. Injection molding plastic parts are subject to molding defects due to various factors, among which the sink marks usually occur in the areas where bosses and ribs are installed. In this study, we analyzed the influence of various factors on the occurrence of sink marks by using the flow analysis of the forming analysis program(Moldflow analysis) using the rib model with the T-shape. Tests have shown that the greatest influence on the sink mark of cosmetic products is the thickness and pressure of the ribs, and the thickness of the basic moulding thickness of the product increases. However, it was considered that the resin temperature and the mold temperature do not greatly affect the occurrence of the sink mark.

• 소성∙가공
• /
• 제14권4호
• /
• pp.360-367
• /
• 2005

The injection-molded plastic parts have many surface defects: warpage, weldline, flowmark, zetting, scratching, shading and so on. As weldline was one of the major surface defects in the case of desktop monitor, warpage and surface shrinkage are the bigger problems of LCD monitor in the pursuit of light weight and thinner thickness of parts. Some measures to improve these defects were introduced in this paper. Based on these, the laboratory work to find out the optimum processing conditions and to get the best parts was repeated injection moulding try-out after reflecting these improvements. The defects of warpage and surface shrinkage was significantly improved after the improvements in the case of the 20.1 inch even if in the 15 and 17inch case the warpage size was a lttle over the allowed specification because of not taking the measure for parts design within the allowable limits from the required specification in the cause of cost down.