• 한국재료학회지
• /
• 제9권4호
• /
• pp.428-433
• /
• 1999

본 연구는 $0.1~1.2\mu\textrm{m}$ 압도분포를 갖는 미세 $Al_2O_3$를 이용하여 플라츠마 용사한 후 상업용 용사분말(Metco 105)과 용사층의 특성을 비교하였다. 미세조직은 미세 $Al_2O_3$층이 상업용분말보다 더 치밀하였고 용샤층의 평균 표면조도 $(R_a)$는 미세 $Al_2O_3$의 경우에 $5.3\mu\textrm{m}$로 상업용 분말 $(R_a=8.2\mu\textrm{m})$ 보다 작은 값을 보였으며, 용사층 평균 splat 두께는 $1.4\mu\textrm{m}$ 였다. 또한 용샤층에는 많은 양의 부분 용융입자가 관찰되었다. XRD분석결과 두 분말 모두 용사층을 이루는 주된 상은 $\gamma-Al_2O_3$이였으며 $\alpha-Al_2O_3$도 관찰되었다. 용사층에 존재하는 $\alpha-Al_2O_3$의 분율은 미세 $Al_2O_3$층의 경우 8.39%. 상업용 $Al_2O_3$의 경우 13.79%이였다. 미세 경도 값은 두 분말에서 큰 차이를 보이지는 않았으나, 미세 $Al_2O_3$의 경우 큰 경도값 편차를 보였으며 따라서 미세 $Al_2O_3$층의 splat의 접합강도는 상업용 $Al_2O_3$보다 상대적으로 낮을 것으로 생각된다.

• 한국표면공학회지
• /
• 제31권2호
• /
• pp.81-90
• /
• 1998

NiCrAly/YSZ(8wt% Y2O3-Zro2) functionally fraded thermal barrier coating (FGC) layers on a Co-base sureralloy (HAYNESS 188) substrate were fabricated using Ar shielded single torch air plasma spraying method. Functional grading were produced with the stepwise compositional change throughout layer thinkness. Microstructural observation revealed a sucessful fabrication of NiCrAly/YSZ FGC. From the results of the curvature measurement, adhesive stength measurement and thermal shock test for the FGC, it was concluded that the optimum enhance of functionally graded coating layer thinkcess and compositional pattern exit to enhance the properties of FGC, which is closely reated to the internal residual distribution with it.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 춘계학술발표대회 개요집
• /
• pp.111-113
• /
• 2003

The existing heating unit is indirect-heating method that make use or the nichrome wire or halogen lamp. The indirect-heating method has the demerits of long warming time, high power consumption and many organization parts. In this study, the heating unit of direct-heating method manufactured as being the thermal spray coating of conductive heating material on the surface of heating unit in order to improve the demerits of indirect-heating method. And YSZ added Ni-20Cr that had moderate electrical resistivity was chosen of the conductive heating material.

• 한국주조공학회지
• /
• 제17권4호
• /
• pp.393-401
• /
• 1997

Commercial flake graphite cast iron substrate was coated with titanium powder by low pressure plasma spraying and was irradiated with a $CO_2$ laser to produce the wear resistant composite layer. From the experimental results of this study, it was possible to composite TiC particles on the surface layer by direct reaction between carbon existed in the cast iron matrix and titanium with thermal sprayed coating by remelting and alloying them using laser irradiation. The cooling rate of laser remelted cast iron substrate without titanium coating was about $1{\times}10^4$ K/s to $1{\times}10^5$ K/s in the order under the condition used in this study. The microstructure of alloyed layer consisted of three zones, that is, TiC particule crystallized zone (MHV $400{\sim}500$), the mixed zone of TiC particule+ledebulite (MHV $650{\sim}900$) and the ledebulite zone (MHV $500{\sim}700$). TiC particules were crystallized as a typical dendritic morphology. The secondary TiC dendrite arms were grown to the polygonized shape and were necking. And then the separated arms became cubic crystal of TiC at the slowly solidified zone. But in the rapidly solidified zone of fusion boundry, the fine granular TiC particules were grouped like grape.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.66-74
• /
• 2004

The sliding wear behavior of $ZrO_2-22wt\%MgO\;(MZ)\;and\;ZrO_2-8wt\%Y_2O_3\;(YZ)$ deposited on a casting aluminum alloy with bond layer (NiCrCoAlY) by plasma spray against an SiC ball was investigated under dry test conditions at room temperature. At all load conditions, the wear mechanisms of the MZ and the YZ coatings were almost the same. The wear mechanisms involved the forming of a smooth film by material transferred on the sliding surface and pullout. The wear rate of the MZ coating was less than that of the YZ coating. With an increase normal load the wear rate of the studied coatings increased. The SEM was used to examine the sliding surfaces and elucidate likely wear mechanisms. The EDX analysis of the worn surface indicated that material transfer was occurred from the SiC ball to the disk. It was suggested that the material transfer played an important role in the wear performance.

• 한국세라믹학회지
• /
• 제39권9호
• /
• pp.851-856
• /
• 2002

산화몰리브덴($MoO_3$)이 첨가된 산화크롬 용사코팅층을 제조하여 산화몰리브덴의 첨가에 따른 고온(450$^{\circ}C$)에서의 플라즈마 용사코팅층에 마찰, 마멸특성을 조사하였다. 마찰, 마멸 특성에 대한 실험을 위하여 왕복동 마멸시험장치를 사용하였다. TEM을 이용하여 코팅층의 미세 구조와 각 상들의 조성을 살펴보았다. 분석 결과에 의하면 산화몰리브덴이 입계로 분산되어 있어 코팅층의 경도와 밀도의 증가가 발생하였다. 마멸시험후 마멸면의 물리적 변화와 화학적 조성의 변화를 SEM와 XPS를 통하여 살펴보았다. 산화몰리브덴이 첨가된 코팅층에서 마찰계수의 감소를 관찰할 수 있었다. 산화몰리브덴이 첨가된 코팅의 마멸된 표면에 마찰, 마멸에 유리한 보호막의 형성이 광범위하게 일어남을 알 수 있었다. 이러한 보호막에 몰리브덴이 산화몰리브덴의 형태로 존재하는 것을 XPS 분석을 통하여 알 수 있었다. 보호막에 산화몰리브덴의 존재가 마찰계수를 감소시키는 것으로 생각된다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.51-52
• /
• 2006

[ $Ti_{45}Zr_{38}Ni_{17}$ ] powders were thermally sprayed onto mild steel substrates in air and under a reduced pressure of argon. Several oxides were formed after thermally-spraying the mechanically-alloyed powders in air. After spraying in a reduced pressure of argon, the coating layers obtained from the gently mixed powders consisted of the elemental metals, but an amorphous phase primarily appeared in the thermally-sprayed mechanically-alloyed powders, which transformed into the icosahedral quasicrystal phase and a minor $Ti_2Ni-type$ crystal phase after annealing at 828 K. The Vickers hardness and the contact angle with pure water for the quasicrystal layers were about 7 GPa and $92^{\circ}$ respectively.

• 한국정밀공학회지
• /
• 제14권1호
• /
• pp.142-149
• /
• 1997

Ceramic-coated anilox roll for printing is resistant to corrosion and wear, and hence has enhanced life and quality. Laser engraving is used typically for machining holes to store ink in this roll. Since engraved hole size and shape are directly related to laser processing parameters, it is necessary to know the rela- tionships among these parameters. In this study, the parameters for engraving of ;oasma sprayed ceramic coatings with Nd:YAG laser were studied. Relationships between hole shape and processing parameters were analyzed. Cr$_{2}$O$_{3}$ceramic was found to be most suitable for Nd:YAG laser engraving. It was found that hole depth can be increased by using higher energy pulses. Effect of using different assistant gases was small to the final results. For better results, it was suggested to use a very stable laser with shorter pulses and higher pulse energy.

• 한국표면공학회지
• /
• 제34권5호
• /
• pp.499-502
• /
• 2001

Functionally gradient NiCrAlY/$ZrO_2$-$Y_2$$O_3$ and NiCrAlY/$ZrO_2$- $CeO_2$-$Y_2$$O_3$ coatings were prepared by APS. The as-sprayed microstructure consisted of metal-rich and ceramic-rich regions, between which $Al_2$$O_3$-rich layers existed owing to the oxidation during APS. During oxidation between 900 and $1100^{\circ}C$ in air, the pre-existing $Al_2$$O_3$-rich scales grew, due mainly to the preferential reaction of Al with inwardly transporting oxygen along the heterogeneous phase boundaries. As the amount of ceramics in the coating increased, the oxidation resistance increased.

• Journal of Periodontal and Implant Science
• /
• 제25권2호
• /
• pp.418-437
• /
• 1995

The effect of the hydroxyapatite coatings on Titanium implants has been the subject of recent investigations. So far, the use of HA coating remains substantially controversial.This study was aimed to evaluate histologically the bone healing patterns around titanium plasm sprayed(TPS) amd HA-coated implant after implantation into the femur neck of ten adult dogs. After implantation, animals were sacrificed at the intervals of 2,4,6,8 and 12 weeks.The fluorescent dyes were injected on the postoperative 4th and 12th week into the animals supposed to be killed at the 12th week. The morphology and direction of new bone formation was similar in both TPS and HA-coated implants.There was a tendency toward more bone formation in the cortical bone area than in the cancellous bone area. Histologically,in the interface of the HA-coated implants, bone response and bone maturation was faster, compared to the TPS implants in the 2nd and 4th week. By fluorescent microscopy, new bone formation was active in the 4th week around both implants and was directed from the periosteum overlying cortical bone to the cancellous bone. These results suggest that the bone formation and maturation is faster during the early healing stage in the interface of the HA-coated implant and where the cortical bone quality is poor, HA coated implant is superior to the TPS implant in the early phase of new bone formation.