• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1512-1514
• /
• 2001

In this work, PZT thin films were etched as a function of $Cl_2$/Ar and additive $CF_4$ into $Cl_2$(80%)/Ar(20%). The etch rates of PZT films were 1600 $\AA$/min at $Cl_2$(80%)/Ar(20%) gas mixing ratio and 1973 $\AA$/min at 30% additive $CF_4$ into $Cl_2$(80%)/Ar(20%). Therefore the etch rate of PZT in $CF_4/Cl_2/Ar$ plasma is faster than in $Cl_2$/Ar. From XPS and SIMS analysis, metal halides and C-O, FCI and $CClF_2$ were detected. The etching of PZT films in Cl-based plasma is primarily chemically assisted ion etching and the remove of nonvolatile etch byproducts is the dominant step. Consequently, we suggest that the increase of Cl radicals and the volatile oxy-compound such as $CO_y$ are made by adding $CF_4$ into $Cl_2$/Ar plasma. Therefore, the etch rate of PZT in $CF_4/Cl_2/Ar$ plasma is faster than in $Cl_2$/Ar. The etched profile of PZT films was obtained above 70$^{\circ}$ by the SEM micrograph.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.4
• /
• pp.145-149
• /
• 2016

The effect of process parameters such as plasma composition, ICP (Inductively Coupled Plasma) source power and rf chuck power on the etch characteristics of GaN epitaxy layer was studied. $Cl_2/Ar$ ICP discharges showed higher etch rates than $SF_6/Ar$ discharges because of the higher volatility of $GaCl_x$ etch products than $GaF_x$ compounds. As the Ar ratio increases in the $Cl_2/Ar$ ICP discharges, the etch anisotropy was enhanced due to the improved physical component of the etching. For both plasma chemistries, the GaN etch rate increased continuously as both the ICP source power and rf chuck power increased, and a maximum etch rate of 251.9 nm/min was obtained at $13Cl_2/2Ar$, 750W ICP power, 400W rf chuck power and 10 mTorr condition.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.11
• /
• pp.826-830
• /
• 2013

In this paper, we carried out the investigations of both etch characteristics and mechanisms for the $SnO_2$ thin films in $O_2/BCl_3/Ar$ plasma. The dry etching characteristics of the $SnO_2$ thin films was studied by varying the $O_2/BCl_3/Ar$ gas mixing ratio. We determined the optimized process conditions that were as follows: a RF power of 700 W, a DC-bias voltage of - 150 V, and a process pressure of 2 Pa. The maximum etch rate was 509.9 nm/min in $O_2/BCl_3/Ar$=(3:4:16 sccm) plasma. From XPS analysis, the etch mechanism of the $SnO_2$ thin films in the $O_2/BCl_3/Ar$ plasma can be identified as the ion-assisted chemical reaction while the role of ion bombardment includes the destruction of the metal-oxide bonds as well as the cleaning of the etched surface form the reaction products.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.4
• /
• pp.298-303
• /
• 2003

Bi$_4$-$_{x}$EU$_{x}$Ti$_3$O$_{12}$ (BET) thin films were etched by inductively coupled CF$_4$/Ar plasma. We obtained the maximum etch rate of 78 nm/min at the gas mixing ratio of CF$_4$(10%)/Ar(90%). The variation of volume density for F and Ar atoms are measured by the optical emission spectroscopy. As CF$_4$increased in CF$_4$/Ar plasma, the emission intensities of F increase, but Ar atoms decrease, which confirms our suggestion that emission intensity is proportional to the volume density of atoms. From X-ray photoelectron spectroscopy, the intensities of the Bi-O, the Eu-O and the Ti-O peaks are changed. By pure Ar plasma, intensity peak of the oxygen-metal (O-M : TiO$_2$, Bi$_2$O$_3$, Eu$_2$O$_3$) bond was seemed to disappear while the intensity of pure oxygen peak showed an opposite tendency. After the BET thin films was etched by CF$_4$/Ar plasma, the peak intensity of O-M bond increase slowly, but more quickly than that of peak belonged to pure oxygen atoms due to the decrease of Ar ion bombardment. Scanning electron microscopy was used to investigate etching Profile. The Profile of etched BET thin film was over 85$^{\circ}$./TEX>.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.6
• /
• pp.251-255
• /
• 2009

In this study, the plasma etching of the TaN thin film with $O_2/BCl_3$/Ar gas chemistries was investigated. The equipment for the etching was an inductively coupled plasma (ICP) system. The etch rate of the TaN thin film and the selectivity of TaN to $SiO_2$ and PR was studied as a function of the process parameters, including the amount of $O_2$ added, an RF power, a DC-bias voltage and the process pressure. When the gas mixing ratio was $O_2$(3 sccm)/$BCl_3$(6 sccm)/Ar(14 sccm), with the other conditions fixed, the highest etch rate was obtained. As the RF power and the dc-bias voltage were increased, the etch rate of the TaN thin film was increased. X-ray photoelectron spectroscopy (XPS) was used to investigate the chemical states of the surface of the TaN thin film.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.6
• /
• pp.229-233
• /
• 2007

In this study, we carried out an investigation of the etching characteristics(etch rate, selectivity) of $HfO_2$ thin films in the $CH_4/Ar$ inductively coupled plasma. It was found that variations of input power and negative dc-bias voltage are investigated by the monotonic changes of the $HfO_2$ etch rate as it generally expected from the corresponding variations of plasma parameters. At the same time, a change in either gas pressure or in gas mixing ratio result in non-monotonic etch rate that reaches a maximum at 2 Pa and for $CH_4(20%)/Ar(80%)$ gas mixture, respectively. The X-ray photoelectron spectroscopy analysis showed an efficient destruction of the oxide bonds by the ion bombardment as well as showed an accumulation of low volatile reaction products on the etched surface. Based on these data, the ion-assisted chemical reaction was proposed as the main etch mechanism for the $CH_4-containing$ plasmas.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.4
• /
• pp.220-225
• /
• 2004

A new ion beam extraction system is designed using a simple ion mass filter and a micro mass balance and a QMS based detecting system. A quadrupole Mass Filter is used for selective ion beam formation from inductively coupled high density plasma sources with appropriate electrostatic lens and final analyzing QMS. Also a quartz crystal microbalance is set between a QMF and a QMS to measure the etching and polymerization rate of the mass selected ion beam. An inductively coupled plasma was used as a ion/radical source which had an electron temperature of 4-8 eV and electron density of $4${\times}$10^{11}$＃/㎤. A computer interfaced system through 12bit AD-DA board can control the pass ion mass of the qmf by setting RF/DC voltage ratio applied to the quadrupoles so that time modulation of pass ion's mass is possible. So the direct measurements of ion - surface chemistry can be possible in a resolution of $1\AA$/sec based on the qcm's sensitivity. A full set of driving software and hardware setting is successfully carried out to get fundamental plasma information of the ICP source and analysed $Ar^{+}$ beam was detected at the $2^{nd}$ QMS.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.183-186
• /
• 2004

The dry etch behavior of PZT thin films was investigated in $BCl_3/N_2$ plasma. The experiments were carried out with measuring etch rates and selectivities of PZT to $SiO_2$ as a function of gas concentration and input rf power, chamber pressure. The maximum etch rate was 126 nm/min when 30% $N_2$ was added to $BCl_3$ chemistry. Also, as input rf power increases, the etch rate of PZT thin films was increased. Langmuir probe measurement showed the noticeable influence of $BCl_3/N_2$ mixing ratio on electron temperature and electron density as input rf power increased. The variation of Cl radical density as plasma parameters changed was examined by Optical Emission Spectroscopy (OES) analysis. According to X-ray diffraction (XRD) analysis, PZT thin films were damaged in plasma and an increase in (100), (200) and (111) phases showed the improvement in structure of the PZT thin films after the $O_2$ annealing process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.190-194
• /
• 2002

In this study, the etching of Au thin films have been performed in an inductively coupled CF4/Cl2/Ar plasma. The etch properties were measured as the CF4 adds from 0 % to 30 % to the Cl2/(Cl2 + Ar) gas mixing ratio of 0.2. Other parameters were fixed at a rf power of 700 W, a dc bias voltage of 150 V, a chamber pressure of 15 mTorr, and a substrate temperature of $30^{\circ}C$. The highest etch rate of the Au thin film was 370 nm/min at a 10 % additive CF4 into Cl2/(Cl2 + Ar) gas mixing ratio of 0.2. The surface reaction of the etched Au thin films was investigated using x-ray photoelectron spectroscopy (XPS) analysis. From x-ray photoelectron spectroscopy (XPS) analysis, the intensities of Au peaks are changed. There is a chemical reaction between Cl and Au. Au-Cl is hard to remove on the surface because of its high melting point and the etching products can be sputtered by Ar ion bombardment. We obtained the cleaned and steep profile.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1294-1296
• /
• 1998

Platinum thin films which hardly form volatile compounds with any reactive gas at normal process temperature was etched in Inductively Coupled Plasma (ICP) using Ar/HBr/$Cl_2$ gases. It is observed that the etch rate of platinum is reduced as increasing of HBr/$Cl_2$ gas mixing ratio when Ar gas ratio is fixed. However, we obtain good etching profile of platinum films without unwanted residues in 90% Ar/5% HBr/5% $Cl_2$ gas mixing ratio.