• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.9
• /
• pp.714-719
• /
• 2001

SrBi$_2$Ta$_2$$O_{9}$ thn films were etched in inductively coupled Cl$_2$/CF$_4$/Ar plasma. THe maximum etch rate was 1060 $\AA$/min at a Cl$_2$/(Cl$_2$+CF$_4$+Ar)=0.2. The 20% additive Cl$_2$ into CF$_4$/Ar plasma decreased carbon and fluorine radicals, but increased Cl radicals. Sr was effectively removed by reacting with Cl radical because the boiling point of SrCl$_2$(125$0^{\circ}C$) is lower than that of SrF$_2$(246$0^{\circ}C$). The chemical reactions on the etched surface were studied with x-ray photoelectron spectroscopy and secondary ion mass spectrometry. The etching profile was evaluated by using scanning electron microscopy.y.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.5
• /
• pp.211-215
• /
• 2001

SBT thin films were etched at different content of $Cl_2$ in $Cl_2$/Ar or $Cl_2/N_2$(80%). As $Cl_2$ gas increased in $Cl_2$/Ar or $Cl_2/N_2$ gas plasma. the etch rate decreased. The result indicates that physical puttering of charged particles is dominant to chemical reaction in etching SBT thin films. To evaluate the etching mechanism of SBT thin films, x-ray photoelectron to chemical reaction in etching SBT thin films. To evaluate the etching mechanism of SBT thin films, x-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS) and atomic force microscopy (AFM) were carried out. From the result of AFM, the rms values of etched samples in Ar only or $Cl_2$ only plasma were higher than that of as-deposited, $Cl_2$/Ar and $Cl_2/N_2$ plasma. This can be illustrated by a decrease of Bi content of nonvolatile etching products (Sr-Cl and Ta-Cl), which are revealed by XPS and SIMS.

• Journal of Powder Materials
• /
• v.27 no.4
• /
• pp.293-299
• /
• 2020

W₂C is synthesized through a reaction-sintering process from an ultrafine-W and WC powder mixture using spark plasma sintering (SPS). The effect of various parameters, such as W:WC molar ratio, sintering temperature, and sintering time, on the synthesis behavior of W₂C is investigated through X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) analysis of the microstructure, and final sintered density. Further, the etching properties of a W₂C specimen are analyzed. A W₂C sintered specimen with a particle size of 2.0 ㎛ and a relative density over 98% could be obtained from a W-WC powder mixture with 55 mol%, after SPS at 1700℃ for 20 min under a pressure of 50 MPa. The sample etching rate is similar to that of SiC. Based on X-ray photoelectron spectroscopy (XPS) analysis, it is confirmed that fluorocarbon-based layers such as C-F and C-F2 with lower etch rates are also formed.

• Journal of the Korean Ceramic Society
• /
• v.40 no.9
• /
• pp.886-890
• /
• 2003

The etching characteristics of a LiNbO$_3$ single crystal have been investigated using helicon wave plasma source with bias power and the mixture of CF$_4$, HBr, SF$_{6}$ gas parameters. The etching rate of LiNbO$_3$ with etching parameters was evaluated by surface profiler. The etching surface was evaluated by Atomic Force Microscopy (AFM). The surface morphology of the etched LiNbO$_3$ changed with bias power and the mixture of CF$_4$/Ar/Cl$_2$, HBr/Ar/Cl$_2$, and SF$_{6}$/Ar/Cl$_2$ parameters. Optimum etching conditions, considering both the surface flatness and etch rate were determined.

• Korean Journal of Materials Research
• /
• v.11 no.6
• /
• pp.527-532
• /
• 2001

Dry etching of copper film using $O_2$ plasma and H(hfac) has been investigated. A one-step process consisting of copper film oxidation with an $O_2$ plasma and the removal of surface copper oxide by the reaction with H(hfac) to form volatile Cu(hfac)$_2$ and $H_2O$ was carried but. The etching rate of Cu in the range from 50 to 700 /min was obtained depending on the substrate temperature, the H(hfac)/O$_2$ flow rate ratio, and the plasma power. The copper film etch rate increased with increasing RF power at the temperatures higher than 215$^{\circ}C$. The optimum H(hfac)/O$_2$ flow rate ratio was 1:1, suggesting that the oxidation process and the reaction with H(hfac) should be in balance. Cu patterning using a Ti mask was performed at a flow rate ratio of 1:1 on 25$0^{\circ}C$\ulcorner and an isotropic etching profile with a taper slope of 30$^{\circ}$was obtained. Cu dry patterning with a tapered angle which is necessary for the advanced high resolution large area thin film transistor liquid-crystal displays was thus successfully obtained from one step process by manipulating the substrate temperature, RF power, and flow rate ratio.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.105-105
• /
• 2009

$ZrO_2$ is one of the most attractive high dielectric constant (high-k) materials. As integrated circuit device dimensions continue to be scaled down, high-k materials have been studied more to resolve the problems for replacing the EY31conventional $SiO_2$. $ZrO_2$ has many favorable properties as a high dielectric constant (k= 20~25), wide band gap (5~7 eV) as well as a close thermal expansion coefficient with Si that results in good thermal stability of the $ZrO_2/Si$ structure. In order to get fine-line patterns, plasma etching has been studied more in the fabrication of ultra large-scale integrated circuits. The relation between the etch characteristics of high-k dielectric materials and plasma properties is required to be studied more to match standard processing procedure with low damaged removal process. Due to the easy control of ion energy and flux, low ownership and simple structure of the inductively coupled plasma (ICP), we chose it for high-density plasma in our study. And the $BCl_3$ included in the gas due to the effective extraction of oxygen in the form of $BCl_xO_y$ compound In this study, the surface kinetic properties of $ZrO_2$ thin film was investigated in function of Ch addition to $BCl_3/Ar$ gas mixture ratio, RF power and DC-bias power based on substrate temperature. The figure 1 showed the etch rate of $ZrO_2$ thin film as function of gas mixing ratio of $Cl_2/BCl_3/Ar$ dependent on temperature. The chemical state of film was investigated using x-ray photoelectron spectroscopy (XPS). The characteristics of the plasma were estimated using optical emission spectroscopy (OES). Auger electron spectroscopy (AES) was used for elemental analysis of etched surface.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.118.2-118.2
• /
• 2016

3D NAND 제조에 있어 high-aspect-ratio etch 공정을 견뎌낼 수 있는 hardmask 소재로서 amorphous carbon layer (ACL) 가 각광받고 있으며 hardmask로서의 특성을 향상시키기 위해 다양한 연구가 진행중에 있다 [1]. 본 연구팀의 기존 연구에서 질소 및 붕소 doping 된 ACL 박막의 etch rate 및 Raman 분석을 통해 박막 특성을 확인한 바 있었으나, 공정 중 arcing이 일어나는 등 의도치 않은 문제로 인해 공정 최적화에 일부 문제가 존재하였다. 본 연구에서는 plasma enhanced chemical vapor deposition (PECVD) 공정을 통해 C6H12 기체 및 doping을 위한 NH3 와 B2H6 두 기체를 이용하여 특성 개선된 ACL을 증착하는 과정에서 발생하는 arcing 및 증착 특성을 규명하고자 진공 내 입자의 수농도를 실시간 측정할 수 있는 particle beam mass spectrometer(PBMS)를 적용, 특정 공정 사건 진단 및 해당 사건에서 발생하는 입자를 분석, 증착된 박막의 Raman spectroscopy 결과와 비교 분석하였다.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.322-325
• /
• 2003

BST thin films were etched with inductively coupled plasmas. A chemically assisted physical etch of BST was experimentally confirmed by ICP under various gas mixtures. After a 20 % addition of $BCl_3$ to the $Cl_2/Ar$ mixture, resulting in an increased the chemical effect. As a increases of RF power, substrate power, and substrate temperature, and decrease of working pressure, the ion energy flux and chlorine atoms density increased. The maximum etch rate of the BST thin films was 90.1 nm/min at the RF power, substrate power, working pressure, and substrate temperature were 700 W, 300 W, 1.6 Pa, and 20 $^{\circ}C$, respectively. It was proposed that sputter etching is dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching product.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.11
• /
• pp.933-938
• /
• 2002

(Ba,Sr)TiO$_{4}$ (BST) thin films on Pt/Ti/SiO$_{2}$/Si substrates were deposited by a sol-gel method and the etch characteristics of BST thin films have been investigated as a function of gas mixing ratio. The maximum etch rate of the BST films was 440 $AA$/min under such conditions as: CF$_{4}$(CF$_{4}$＋Ar) of 0.2, RF-power of 700 W, DC-bias voltage of -200 V, pressure of 15 mTorr and substrate temperature of 30 $^{circ}C$. The selectivities of BST to Pt, SiO$_{2}$ and PR were 0.38, 0.25 and 0.09, respectively. In the XPS (X-ray photoelectron spectroscopy) analysis, Barium (Ba) and Strontium (Sr) component in BST thin films formed low volatile compounds such as BaFx, SrFx, which are forms by the chemical reaction with F atoms and is removed by Ar ion bombardment. Titanium (Ti) is removed by chemical reaction such as TiF with ease. The result of secondary ion mass spectrometry (SIMS) analysis confirmed the existence of the BaFx, SrFK, TiFx.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.102-102
• /
• 2008

Sapphire (${\alpha}-Al_2O_3$) has been used as the substrate of opto-electronic device because of characteristics of thermal stability, comparatively low cost, large diameter, optical transparency and chemical compatibility. However, there is difficulty in the etching and patterning due to the physical stability of sapphire and the selectivity with sapphire and mask materials [1,2]. Therefore, sapphire has been studied on the various fields and need to be studied, continuously. In this study, the etching properties of sapphire substrate were investigated with various $CH_4$/Ar gas combination, radio frequency (RF) power, DC-bias voltage and process pressure. The characteristics of the plasma were estimated for mechanism using optical emission spectroscopy (OES). The chemical compounds on the surface of sapphire substrate were investigated using energy dispersive X-ray (EDX). The chemical reaction on the surface of the etched sapphire substrate was observed by X-ray photoelectron spectroscopy (XPS). Scanning electron microscopy (SEM) was used to investigate the vertical and slope profiles.