• Textile Coloration and Finishing
• /
• v.34 no.2
• /
• pp.102-108
• /
• 2022

The physicochemical properties of stainless steel fibers which were modified by oxygen plasma treatment were analyzed through microscopy and XPS analysis. The wettability of the surface of the stainless steel fiber was observed by measuring water contact angle to find out the effect of the plasma treatment time on the surface characteristics of the stainless steel fiber. In addition, in order to understand the effect of oxygen plasma treatment on the deterioration of the stainless steel fiber properties, the physical properties due to plasma treatment was investigated by measuring the weight reduction, tensile strength, elongation, tensile modulus of the stainless steel fibers according to the treatment time. As a result, the stainless steel fiber surface was etched by the oxygen plasma and the surface became more wettable by the introduction of hydrophilic functional groups. However the physical properties of the stainless steel fiber were not significantly deteriorated even if the surface of the stainless steel fiber made hydrophilic.

• Nuclear Engineering and Technology
• /
• v.56 no.4
• /
• pp.1145-1152
• /
• 2024

To realize an initial objective of the negative ion-based neutral beam injection (N-NBI) at the Comprehensive Research Facility for Fusion Technology (CRAFT) test facility, which targets an H⁰ beam power of 2 MW at an energy of 200-400 keV and a pulse duration of 100 s, it is crucial to study the cesium dynamics of the negative ion source. Here a numerical simulation program CSFC3D is developed and applied to simulate the distribution and time dynamics of cesium during short pulses. The calculations show that most of the cesium on the plasma grid (PG) area originates from the release of cesium that is accumulated within the ion source in the plasma phase. Increasing the wall temperature reduces the loss of cesium on the wall of the ion source. Furthermore, the thickness of the cesium monolayer is directly influenced by the PG temperature. Both simulated and experimental results demonstrate that maintaining the PG temperature between 180 ℃ and 200 ℃ is essential for enhancing the performance of the ion source and optimizing the cesium behavior.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.470-474
• /
• 2006

This dissertation discuses about a ferrite core plasma source using low operating frequency without sputtering problem by the stored electric field. Compared with the conventional RF power system with 13.56MHz switching frequency, the proposed plasma power system is only separated at 400kHz, so that it makes possible to use of low cost switching elements, PWM control and soft switching. Moreover, it could improve the coupling efficiency for plasma and antenna by using the ferrite core in order to transfer the energy of the load This dissertation tried to analyze new plasma generation method for the plasma generation system by modeling the plasma load and grafting the concept of impedance matching in order to interpret it with the formula This dissertation verified the ferrite core inductive coupling plasma source authorized for 400kHz of low frequency power by applying to the semi-conductor ash process thru the measurement of ash capacity and uniformed plasma distribution on the actual wafer.

• Preventive Nutrition and Food Science
• /
• v.3 no.4
• /
• pp.379-381
• /
• 1998

An angiotensin converting enzyme (ACE) inhibitor was isolated and partially purified from bovine blood plasma. Bovine blood plasma was obtained after removing blood cells by centrifugation, followed by the addition of anticoagulant to whole bovine blood. To precipitate plasma proteins, bovine blood plasma was treated with 4% trichloroacetic acid (TCA) as a final concentration .An ACE inhibitor was isolated from TCA supernatnat, using ultrafiltration, gel permeation chormatography, and reverse-phase high pressure liquid chromatogrpahy. The ACE inhibitor purified from TCA supernatant had IC50 values of 9.4$\mu$M.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.4 no.3
• /
• pp.67-76
• /
• 1995

An experimental study of hot machining has performed to improve the machinability of Inconel718. This experiment used plasma are for heating materials and Whisker0reinforce aluminum oxide ceramic tool insert. An assembled plasma heating system are described and experimental results from both conventional and plasma hot machining of Inconel 718 are compared. The experiments with plasma heating demonstrated the following effectiveness. 1)The cutting force was reduced with increasing surface temperature of workpiece from 450$^{\circ}C$ up to 720$^{\circ}C$ as much as approximately from 20 to 40%. 2) Surface roughness(Ra) was improved by as much as a factor 2 in case of one pass cutting with new ceramic tool inserts.3) The depth of cut notch were at promary cutting tool was significantly reduced.

• Journal of Astronomy and Space Sciences
• /
• v.5 no.1
• /
• pp.1-8
• /
• 1988

Electron beam propagation in a fully ionized plasma has been studied using a one-dimensional particle simulation model. We compare the results of electrostatic simulations to those of electromagnetic simulations. The electrostatic results show the essential features of beam-plasma interactions. It is found that the return currents are enhanced by the beam-plasma instability which accelerates ambinet plasmas. The results also show the heating of ambient plasmas and the trapping of plasmas due to the locally generated electric field. The electromagnetic simulations show much the same results as the electrostatic simulations do. The level of the radiation generated by the same non-relativistic beam is slightly higher than the noise level. We discuss the results in context in context of the heating of coronal plasma during solar flares.

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.4
• /
• pp.89-94
• /
• 2009

The influence on a stability of thermal plasma has been investigated in an electrode structure of non-transferred plasma torch. The variations of dynamic characteristic of the arc voltage was analyzed and compared in terms of voltage character and nozzle types for both the step-shaped nozzles and magnetic-approved cylindrical nozzle. From the experimental results, an electrode gap, flow rate of arc gas, and currents are considered as major operational parameters. As conclusion, it was assured that a torch with step-shaped nozzles of magnetic-approved type produce the stable plasma jet.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.5
• /
• pp.211-214
• /
• 2007

Chemical and morphological changes of phenol formaldehyde-based photoresist after $O_2$ radiofrequency(RF) plasma treatment depending on exposure time and source power were investigated. It was found that etch rate of photoresist sharply increased after discharge turn on and reached a limit with increase in plasma exposure time. Contact angle measurements and X-ray photoelectron spectroscopy(XPS) analysis showed that the surface chemical structure become nearly constant after 15 sec of the treatment. Atomic force microprobe(AFM) measurements were shown that surface roughness was increased with plasma exposure time.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.3
• /
• pp.122-126
• /
• 2006

In this study, composite materials were put to dry interfacial treatment by use of plasma technology It has been presented that the optimum parameters for the best wettability of the samples at the time of generation of plasma were oxygen atmosphere, 0.1 Torr of system pressure, 100 W of discharge power, and 3 minutes of discharge time. The decrease in surface potential of charged samples by corona discharge indicates that the amount of accumulated electrical charges reduces and the charges that have been injected lessen rapidly when the duration of UV irradiation increases. The surface resistivity and the tensile strength of plasma treated samples, a longer UV irradiation time resulted in decreased insulation.

• Journal of Industrial Technology
• /
• v.23 no.A
• /
• pp.175-179
• /
• 2003

A study on the particle growth in $TEOS/O_2$ plasma was performed by observing the particle size and its morphology by TEM. The qualitative chemical analysis of particles was also determined by the EDS (Energy Dispersive X-Ray Spectrometer). The effects of process variables such as the plasma on-time and bubbler temperature on the particle growth were investigated. The particle size becomes larger as the plasma on-time because of the longer coagulation, and also as the bubbler temperature increases because of the faster coagulation between particles.