• ETRI Journal
• /
• v.38 no.5
• /
• pp.981-987
• /
• 2016

We present a cost-effective dual polarization quadrature phase-shift coherent receiver module using a silica planar lightwave circuit (PLC) hybrid assembly. Two polarization beam splitters and two $90^{\circ}$ optical hybrids are monolithically integrated in one silica PLC chip with an index contrast of $2%-{\Delta}$. Two four-channel spot-size converter integrated waveguide-photodetector (PD) arrays are bonded on PD carriers for transverse-electric/transverse-magnetic polarization, and butt-coupled to a polished facet of the PLC using a simple chip-to-chip bonding method. Instead of a ceramic sub-mount, a low-cost printed circuit board is applied in the module. A stepped CuW block is used to dissipate the heat generated from trans-impedance amplifiers and to vertically align RF transmission lines. The fabricated coherent receiver shows a 3-dB bandwidth of 26 GHz and a common mode rejection ratio of 16 dB at 22 GHz for a local oscillator optical input. A bit error rate of $8.3{\times}10^{-11}$ is achieved at a 112-Gbps back-to-back transmission with off-line digital signal processing.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.3
• /
• pp.278-284
• /
• 2010

In this paper, a millimeter-wave detector using zero-bias schottky diode is designed and fabricated at W-band. It consists of LNA(Low Noise Amplifier) and detector module to improve sensitivity. LNA case with a highly stop-band characteristic is designed to prevent the oscillation by LNA MMIC chip. Diode detector of planar structure is fabricated for the easy connection with LNA module and zero bias Schottky diode is utilized. In practice, the fabricated diode detector have shown the detection voltage of 20~500 mV to the RF input power of -45~-20 dBm. The proposed W-band detector can be applicable to the passive millimeter image system.

• Journal of Advanced Navigation Technology
• /
• v.3 no.2
• /
• pp.139-146
• /
• 1999

A flight simulator is composed of engine, navigation systems and instrument modules. However, two problems exist here. First, the coordinate of each independent module is not same. To solve this problem, we design a method that mutual coordinates are capable of transformation each other. Second, the distance and bearing between two points on the earth are computed in a sphere shape using the spherical trigonometry. However, the computing time is very severe. In this paper, we project the sphere into the planar to reduce the computing time. An experimental result shows that the performance of the proposed method is excellent to both distance and bearing calculations in close region. Also, the computing time is reduced from $4.95{\times}10^{-4}$ seconds to $1.648{\times}10^{-4}$ seconds.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.150-155
• /
• 2006

Carbon nanotubes backlight unit (CNT-BLU) that lightened by field emission was developed into practicability. According to our novel structure, AC mode circuit design and simple printing process, CNT-BLU could achieve 85% of uniformity, 8000 nits of brightness and low material and fabrication cost. Based on these performances, this new planar backlight technology has chances to proceed to mass production and has the potential to replace traditional backlight technology because of its good properties, like the simple processes, easy to large scale, low surface temperature, low power consumption, optical film-free and Hg-free, etc.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.341-345
• /
• 2001

In this study, nano-sized powders of $Si0_2-0^{\sim}15mol%B_2O_3$ composition were prepared by sol-gel processing method using TEOS(Tetra ethyl ortho silicate) and $H_3BO_3$ solution. The powders were tape-cast on High silicate glass sheet(HSG) substrate and sintered to form a layer of undercladding for the planar light wave module, During the sol-gel processing, $H_2O/Si$ mole ratio were varied to modify the size of the powders in a range from 600 to 75nm. The dispersion of the powder was modified by changing the pH of the slurry. Sintering temperature of the tape was observed to decrease with the size of the powder and the $B_2O_3$ content in the powder. When the silica powders of 75-125nm in diameter containing 15mol% $B_2O_3$ were used, 98 TD% was obtained at $1250^{\circ}C$, which is approximately $300^{\circ}C$ reduction in sintering temperature compared with micrometer-sized powders.

• Proceedings of the KIPE Conference
• /
• 2019.11a
• /
• pp.168-169
• /
• 2019

본 논문은 친환경자동차용 저전압 DC-DC 컨버터(Low-voltage DC-DC converter, LDC)의 고전력밀도 달성을 위한 스위칭 주파수 선정 및 구조 설계 방법을 소개한다. 위상천이 풀-브릿지(Phase-Shift Full-Bridge, PSFB) 컨버터의 손실 분석을 통해 스위칭 주파수 700kHz 선정하였으며, 냉각수 온도 65℃, 분당 8리터의 유량 기준으로 소자 온도가 110℃ 이내로 관리 되도록 고려하여 구조 설계를 수행했다. 온도 조건을 만족하면서 8kW/L의 높은 전력밀도를 달성하였으며 입력전압 200V-310V, 출력전압 12.8V-15.1V의 전압 범위를 만족하는 1.8kW 최종 시작품을 제작하여 실험으로 검증하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.341-345
• /
• 2001

In this study, nano-sized powders of SiO$_2$-0∼15mo1%B$_2$O$_3$ composition were prepared by sol-gel processing method using TEOS(Tetra ethyl ortho silicate) and H$_3$BO$_3$ solution. The powders were tape-cast on High silicate glass sheet(HSG) substrate and sintered to form a layer of undercladding for the planar light wave module. During the sol-gel processing, H$_2$O/Si mole ratio were varied to modify the size of the powders in a range from 600 to 75nm. The dispersion of the powder was modified by changing the pH of the slurry. Sintering temperature of the tape was observed to decrease with the size of the powder and the B$_2$O$_3$ content in the powder. When the silica powders of 75∼125nm in diameter containing 15mo1% B$_2$O$_3$ were used, 98 TD% was obtained at 1250$^{\circ}C$, which is approximately 300$^{\circ}C$ reduction in sintering temperature compared with micrometer-sized powders.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.5
• /
• pp.38-45
• /
• 2004

As optical communication is being substituted for telecommunication, the demand of a large variety of fiber optic components is increasing. V-groove substrates, one of the module components, are used to connect optical fibers to optical planar circuits and to arrange fibers. Their applications are multi-channel optical connectors and optical waveguide fiber coupling, etc. Because these substrates are a critical part of the splitter in a multiplexer and a multi fiber connector, precise and reliable fabrication process is required. For precisely aligning core pitch between fibers, machined core pitch tolerance should be within sub-microns. Therefore, these are generally produced by state-of-the-art micro-fabrication like MEMS. However, most of the process equipment is very expensive. It is also difficult to change the process line for custom designs to meet specific requirements using various materials. For various design specifications such as different values of the V angle and low-priced process, the fabrication method should be flexible and low cost. To achieve this goal, we have suggested a miniaturized machine tool with high accuracy positioning system. Through this study, it is shown that this cutting process can be applied to produce V-groove subtracts. We also show the possibility of using a miniaturized machining system for producing small parts.

• International Journal of Internet, Broadcasting and Communication
• /
• v.16 no.1
• /
• pp.330-338
• /
• 2024

In this paper, a Ka-band high-output active phased array antenna device applicable to small radars and seekers was designed, and the improved performance was studied. The radiation device assembly consists of 1x8 arrangements, and the step flared notch antenna type. It shows low active reflection loss characteristics in broadband, and low loss characteristics by applying the air-strip feeding structure, and is designed to enable beam steering up to 45 degrees. The TRM(transmit receive module) output power is more than 2.0W per channel using GaN HPA in the transmitting path, and satisfies more than 25.0 dB gain and less than 6.0 dB noise figure in the receiving path. Accordingly, the Effective Isotropically Radiated Power(EIRP) of the antenna unit shows the performance of 0.00 dB or more and the receive gain-to-noise temperature ratio(G/T) of 0.00 dB/k or more. For demonstration, we have designed aforementioned planar array antenna which consists of 64 radiating elements having a size within 130 mm x 130 mm x 300 mm and weight of less than 4.9 kg..

• Journal of the Korean Society of Radiology
• /
• v.15 no.1
• /
• pp.1-7
• /
• 2021

In order to acquire an image in a positron emission tomography, it is necessary to draw the position coordinates of the scintillation pixels of the detector module measured at the same time. To this end, in a detector module using a plurality of scintillation pixels and a small number of photosensors, it is necessary to obtain a flood image and divide a region of each scintillation pixel to obtain a position of a scintillation pixel interacting with a gamma ray. Alternatively, when the number of scintillation pixels and the number of photosensors to be used are the same, the position coordinates for the position of the scintillation pixels can be directly acquired as digital signal coordinates. A method of using a plurality of scintillation pixels and a small number of photosensors requires a process of obtaining digital signal coordinates requires a plurality of photosensors and a signal processing system. This complicates the signal processing process and raises the cost. To solve this problem, in this study, we developed a method of obtaining digital signal coordinates without performing the process of separating the planar image and region using a plurality of flash pixels and a small number of optical sensors. This is a method of obtaining the position coordinate values of the flash pixels interacting with the gamma ray as a digital signal through a look-up table created through the signals acquired from each flash pixel using the maximum likelihood function. Simulation was performed using DETECT2000, and verification was performed on the proposed method. As a result, accurate digital signal coordinates could be obtained from all the flash pixels, and if this is applied to the existing system, it is considered that faster image acquisition is possible by simplifying the signal processing process.