• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.11
• /
• pp.93-98
• /
• 2003

In this paper, we designed a printed square loop antenna for operating of PCS and IMT2000 band. The proposed antenna has omni-directional radiation patterns with broad bandwidth, similar to the conventional antenna, to easy feed on composing single planar. We obtain an ideal impedance matching and increase bandwidth. An antenna bandwidth is about 150MHz(1.74∼l.89〔GHz〕) at 1$^{st}$ resonance frequency and 290MHz(1.95∼2.24GHz) at 2$^{nd}$ resonance frequency on VSWR(equation omitted)1.5, and then we can obtain not only 1.73∼l.87 〔GHz〕 PCS band but also 1.92∼2.17 (GHz) IMT2000 band. band.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1125-1128
• /
• 2003

This paper presents the design method of a Colpitts type oscillator with coplanar waveguide(CPW) structures in the range of Ka-band frequency for transmitter and receiver modules. Series short stubs of CPW patterns provide inductances and capacitances in the range of Ka-band which can be expressed as a CLC-$\pi$ equivalent circuit. The experimentation has employed ro4003 substrates as a CPW substrate which has a dielectric constant of 3.38 and a signal and ground space of 100um. A method of momentum simulation for the CPW patterns has performed with an ADS software tool of Hewlett-Packard Corp. Inductance and capacitance circuits of a Colpitts oscillator was interconnected to a MESFET with CPW bend structures of including the input and output impedance matching circuits of the active transistor. Circuit parameters for impedance matching were determined through the network conversion to the equivalent length of CPW transmission lines by using T-network 1 $\pi$-network conversion circuit. A Colpitts oscillator was fabricated on the substrate of a area of 8.5mm x 17.4mm with a MESFET of Fujitsu FMM5704X and CPW series short stubs. The design suggested the possibility of realizing oscillators on a planar surface for the wireless system of tansmitter and receiver modules in the frequency range of 30GHz

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.8 no.5
• /
• pp.43-49
• /
• 2008

Motivated by the Communication Broadcasting Convergence service, various technical approaches are being used to develop more efficient antenna models. This paper proposes a compact mobile antenna which is attachable to a cell phone and is applicable for Communication Broadcasting Convergence. In the design of the antennas for mobile handsets, size reduction is a crucial factor. In this paper, the compactness of a loop antenna is realized by bending a folded-dipole. A short planar dipole is transformed to a twice folded dipole and a loop antenna to produce a larger input resistance. The current distribution of the antenna is the same as a loop antenna, and its radiation patterns are omni-directional. We also analyze the performance of the RFID antenna by exploring the current-induced near field radiation patterns using a electro-optic field mapping system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.3
• /
• pp.267-271
• /
• 2004

The joint strength and fracture surface of Sn-Pb solder bump in photo diode packages after isothermal aging testing were studied experimentally. Cu/Sn-Pb solders were adopted, and aged for up to 900 hours at 12$0^{\circ}C$ and 17$0^{\circ}C$ to analyze the effect of intermetallic compound(IMC). In 900-hour aging experiments, the maximum shea strength of Sn-Pb solder decreased by 20％ and 9％. The diffraction patterns of Cu$_{6}$Sn$_{5}$, scallop-shape IMC, and planar-shape Cu$_3$Sn were observed by Transmission Electron Microscopy (TEM).EM).

• Journal of Information Display
• /
• v.1 no.1
• /
• pp.20-24
• /
• 2000

We propose on a novel vertical configuration (VC) for a helix-deformed ferroelectric liquid crystal (HDFLC) display that has fast response, high contrast, analog gray scale capability, and wide-viewing characteristics. In contrast to a conventional HDFLC in a planar geometry, smectic layers arrange themselves parallel to the substrates, and thus, extremely uniform alignment of molecules in large area is naturally achieved in our new configuration without additional processes such as the rubbing and/or electric field treatment. Moreover, with a proper design of electrode patterns on the same substrate, multidomain switching is easily realized without employing any complex process of alignment. Our new VC-HDFLC is expected to provide a viable technology to produce a next-generation large area LCD suitable for processing the dynamic image at a video-rate.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.4
• /
• pp.47-54
• /
• 2007

Simultaneous 3-D LDV measurements of the in-cylinder flows of three different engine setups were summarized for the quantification of the flow characteristics in each vertical or horizontal plane, and in entire cylinder volume. The ensemble averaged-velocity, tumble and swirl motions, and turbulent kinetic energy during the intake and compression strokes were examined from the measured velocity data (approximately 2,000 points for each engine setup). The better spatial resolution of the 3-D LDV allows measurements of the instantaneous flow structures, yielding more valuable information about the smaller flow structures and the cycle-to-cycle variation of these flow patterns. Tumble and swirl ratios, and turbulent kinetic energy were quantified as planar and volumetric quantities. The measurements and calculation results were animated for the visualization of the flow, and hence ease to analysis.

• ETRI Journal
• /
• v.31 no.1
• /
• pp.71-73
• /
• 2009

In this letter, novel antennas with two spiral elements are presented for ultra-wideband application. The original antenna consists of a T-shaped microstrip feed line, two spiral radiating elements, and a ground plane with two circular slots. It measures 30 mm ${\times}$ 40 mm ${\times}$ 1.6 mm. Spiral elements are used to increase the lower bandwidth limit. To further reduce the size of the antenna, the original antenna is cut in half by using the symmetry of the surface current distributions. The proposed antennas feature omnidirectional radiation patterns and good gain flatness.

• Journal of Mechanical Science and Technology
• /
• v.17 no.12
• /
• pp.2116-2124
• /
• 2003

An experimental study providing additional knowledge of quasi-conical symmetry in swept shock wave/turbulent boundary-layer interactions is described. When a turbulent boundary layer on the flat plate is subjected to interact with a swept planar shock wave, the interaction flowfield far from fin leading edge has a nature of conical symmetry, which topological features of the interaction flow appear to emanate from a virtual conical origin. Surface streakline patterns obtained from the kerosene-lampblack tracings have been utilized to obtain representative surface features of the flow, including the location of the virtual conical origin. The scaling law for the sharp-fin interactions suggested by previous investigators has been reexamined for different freestream Mach numbers. It is noticed that the scaling law reasonably agrees with the present experimental data, however, that the law is not appropriate to estimate the location of the virtual conical origin. Further knowledge of the correlation for the virtual conical origin has thus been proposed.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.3
• /
• pp.82-84
• /
• 2008

A surface encoder based on the Half-shaded square pattern (HSSP) is presented. The HSSP working as reference grid is composed of the straight lines which are easy to be fabricated and make measuring time short. Since the periodic cell is separated in ON/OFF by the $45^{\circ}$ straight line, the duration from the starting point of scanning to the first rising edge and the duty cycle of the pulse train vary with respect to the position of the starting point. And the relationship between X and Y position and the duration, and duty cycle is described in the simple linear equation. Therefore, it is possible to measure X and Y position with the measured duration and duty cycle without calculating load. Through the test set-up, the feasibility of the proposed surface encoder was verified. Also the future works for improvement of performance were suggested.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.3
• /
• pp.343-351
• /
• 1988

Planar optical waveguides are fabricated on a Y-cut LiNbO3 single crystal substrate by Ti indiffusion method. From data measured by the bright M-line spectroscopy, refractive index profiles are reconstructed by WKB approximation method. Then, single strip, X-crossing strip, and Y-brinch strip optical waveguides are fabricated on X-cut LiNbO3 single crystal substrate, with waveguide patterns made by the laser beam direct writing method. And their near-field intensity profiles are observed after coupling the light to the waveguide edges.