• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.5
• /
• pp.395-404
• /
• 2012

This paper presents computations of the dynamic derivatives of three dimensional flight vehicle configurations using CFD. The pitch dynamic derivatives are computed from the pitch sinusoidal motion, while the roll damping is computed based on steady state calculation using a non-inertial frame method. The Basic Finner and the SDM(Standard Dynamic Model) are chosen for the benchmark tests against other numerical and experimental results. For the flow calculations, a 3-D Euler solver that can be run both on the non-inertial frame and on the inertial frame is developed. A dual-time stepping method is applied for the unsteady time accurate simulations. A good agreement of pitch-roll dynamic derivatives with previously published numerical results and the experimental results is observed.

• 한국전산유체공학회:학술대회논문집
• /
• 2006.05a
• /
• pp.263-267
• /
• 2006

The path of a flapping airfoil during upstroke and down-stroke is optimized for maximum thrust and propulsive efficiency. The periodic flapping motion in combined pitch and plunge is described using Non-Uniform B-Splines(NURBS). A gradient based algorithm is employed for optimization of the NURBS parameters. Unsteady, low speed laminar flows are computed using a Navier-Stokes solver in a parallel computing environment based on domain decomposition. It is shown that the thrust generation is significantly improved in comparison to the sinusoidal flapping motion. For a high thrust generation, the airfoil stays at a high effective angle of attack for short durations.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.5
• /
• pp.368-375
• /
• 2018

In the present study, aerodynamic load analysis for a floating off-shore wind turbine was conducted to examine the effect of periodic platform motion in the direction of 6-DOF on rotor aerodynamic performance. Blade-element momentum method(BEM) was used for a numerical simulation, the unsteady airload effects due to the flow separation and the shed wake were considered by adopting a dynamic stall model based on the indicial response method. Rotor induced downwash was estimated using the momentum theory, coupled with empirical corrections for the turbulent wake states. The periodic platform motions including the translational motion in the heave, sway and surge directions and the rotational motion in the roll, pitch and yaw directions were considered, and each platform motion was applied as a sinusoidal function. For the numerical simulation, NREL 5MW reference wind turbine was used as the target wind turbine. The results showed that among the translation modes, the surge motion has the largest influence on changing the rotor airloads, while the effect of pitch motion is predominant for the rotations.

• Structural Engineering and Mechanics
• /
• v.52 no.3
• /
• pp.633-646
• /
• 2014

A semi-analytical numerical approach for the effective structural dynamic response analysis of spar floating substructure for offshore wind turbine subject to wave-induced excitation is introduced in this paper. The wave-induced rigid body motions at the center of mass are analytically solved using the dynamic equations of rigid ship motion. After that, the flexible structural dynamic responses of spar floating substructure for offshore wind turbine are numerically analyzed by letting the analytically derived rigid body motions be the external dynamic loading. Restricted to one-dimensional sinusoidal wave excitation at sea state 3, pitch and heave motions are considered. Through the numerical experiments, the time responses of heave and pitch motions are solved and the wave-induced dynamic displacement and effective stress of flexible floating substructure are investigated. The hydrodynamic interaction between wave and structure is modeled by means of added mass and wave damping, and its modeling accuracy is verified from the comparison of natural frequencies obtained by experiment with a 1/100 scale model.

• The Korean Journal of Physiology
• /
• v.24 no.1
• /
• pp.103-113
• /
• 1990

The role of cervical proprioceptors in the control of body posture was studied in bilaterally labyrinth-ectomized, decerebrate cats. The animals were suspended on hip pins with the neck extended horizontally. With this placement the EMG activities of extensor and flexor muscles of the upper extremities were observed by means of sinusoidal head rotator. The rotator can induce two kinds of neck movement: The one is 'pitch' which describes a rotatory neck motion to transverse axis of the body and mainly occurs at skull-C1 (atlantooccipital) joint and the other is 'roll', side-to-side relation of the neck to longitudinal axis, whose center is C1-C2 (atlanto-axial) joint. The following results were obtained. 1) Responses of EMG activity were closely dependent on the rotatory range of the neck. And the EMG activity was not changed during sustained neck torsion, eliciting a typical tonic neck reflex. 2) On pitching movement, the head-up rotation produced the excitation of bilateral triceps muscles, whereas the head-down rotation produced the inhibition. And the response of bilateral biceps muscles was the opposite to that of triceps. 3) On rolling movement, the side-up rotation of the head produced the excitation of ipsilateral triceps muscles and the inhibition of contralateral ones. And the response of biceps muscles was the opposite to that of triceps. 4) The minimum requirement of motion to evoke EMG activities in the upper extremities was $3.2^{\circ}{\sim}12.5^{\circ}$. These results have shown that the cervical proprioceptors produce tonic discharge on the upper brachial muscles, regulate the EMG activities of those muscles, and are very sensitive to neck rotation. And it can be stated that the cervical proprioceptors may play an important role in the control of body posture and movement.

• 한국기계연구소 소보
• /
• s.14
• /
• pp.17-31
• /
• 1985

The Primary object of this study is to predict rigid carbody's vertical and pitch acceleration and/or displacement frequency response to vertical sinusoidal rail surface irregularities for any specified point of the carbody, and to verify the predictions by means of experiments. The developed computer program also calculates vertical and pith transmissibilities and acceleration spectra. This model can be used for first order analysis of ride behabior. it's main advantage is its simplicity and ease of use. This model can be used for first order analysis of ride quality behabior. It's main advantage is its simplicity and ease of use. The model was designed with 6 degreed of freedom. Equations of motion were derived by Lagrangian method. This calculation was applied to the vertical dynamic analysis in order to pursue a possible improvement of the dynamic performance of co-co locomotive, and results were very useful.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.565-568
• /
• 1995

This paper presents the position control of a closed-loop cylinder system using ER(electro-rheological)valve actuators. Following the field-dependent pressure analysis of the ER valve actuators on the basis of Bingham model of ER fluids, a 3 d.o.f. close-loop sylinder system having the heave, roll and pitch motions is proposed. The governing equations of motion are derived using Lagrange's equation, and a control model is established by considering system uncertain parameters such as load conditions. A sliding mode controller which has inherent robustness to system uncertainties is adopted to achieve robust tracking control performance. Tracking control results for sinusoidal trajectory were presented in order to demonstrate the effectiveness of the proposed control system.