• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.177-181
• /
• 1996

A fundamental study for the production of an internal combustion engine piston by forging is performed through UBET(Upper Bound Elemental Technique) analysis and experiments. In UBET analysis, an optimal preform of the aluminum piston is predicted and the results are compared with the experimental results. The internal flow pattern and and the forging loads according to the different friction condition are investigated.

• 한국자동차공학회논문집
• /
• 제1권2호
• /
• pp.69-76
• /
• 1993

The program for the development of linkage system was made and the scissors-type linkage system was designed. The piston temperature distribution under steady state was measured by the linkage system and thermocouple. The effects of engine speed, coolant outlet temperature, and torque on the piston temperature were investigated.

• Journal of Biosystems Engineering
• /
• 제17권4호
• /
• pp.305-313
• /
• 1992

Stirling 기관(機關)의 피스톤 Seal부분에서의 마찰저항(摩擦抵抗)을 감소(減少)시킴과 동시 에 작동가스의 누설량(漏泄量)을 감소(減少)시켜서 기관출력(機關出力)을 증대(增大)시킬 목적(目的)으로 재질(材質) 및 밀봉(密封) 형식(形式)이 서로 다른 Piston ring식 밀봉기구(密封機構)와 금속(金屬) Bellows를 이용한 밀봉기구(密封機構)를 시작(試作)해서 마찰저항(摩擦抵抗)과 작동가스의 누설량(漏泄量)을 조사(調査)하고, 이들 밀봉기구(密封機構)를 실험(實驗) 기관(機關)에 장착(裝着)해서 운전시험(運轉試驗)을 통해 각 밀봉기구(密封機構)의 성능(性能)을 검토(檢討)하였다. 그 결과(結果) Bellows를 Power piston의 Actuator로 시작(試作)한 밀봉기구(密封機構)가 다른 Piston-ring식(式) 밀봉기구(密封機構)에 비(比)해, 피스톤링과 실린더벽 사이의 마찰저항(摩擦抵抗) 및 작동(作動)가스의 누설량(漏泄量)이 현저하게 감소(減少)하였으며, D-type은 B-type에 비해 도시출력(圖示出力)은 약 1.6배, 축출력(軸出力)은 약 1.2배로 증가(增加)하였다.

• 한국자동차공학회논문집
• /
• 제3권1호
• /
• pp.108-117
• /
• 1995

The primary purpose of this extensive test effort was to observe real-time operational performance characteristics associated with automotive grade fuel utilized by piston engine powered light aviation aircraft. In fulfillment of this effort, baseline engine operations were established with 100LL aviation grade fuel followed by four blends of automotive grade fuel. A comprehensive sea-level-static test cell/flight test data collection and evaluation effort were conducted to review operational characteristics of a carbureted light aircraft piston engine as related to fuel volatility, fuel temperature, and fuel system pressure. Presented herein are results, data, and conclusions drawn from test cell engine operation as well as flight test operation on 100LL aviation grade and four blends of automotive grade fuel.

• 한국해양공학회지
• /
• 제13권3B호
• /
• pp.47-55
• /
• 1999

A study on swirl chamber for diesel engine is to realize lower fuel consumption and exhaust emission than the current marketing engines. Author formerly reported the performance characteristics of small IDI diesel engine with swirl chamber by changing the jet passage area and its angle, and the depth and shape of the piston top cavity. Following after the first report, in this paper, the characteristics of fuel consumption, soot emission, and exhaust gas temperature were examined and analyzed after dimension of jet passage area expanded to $70.1mm^2$ The results were that the optimum values of the jet passage area depending on the depth of the piston top cavity were different at each engine speeds and loads, and in accordance with application of engine running conditions they were able to be selected as optimum dimensions of each design parameters.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권5호
• /
• pp.554-564
• /
• 2002

A newly designed combustion chamber of diesel engine with a modified piston crown was prepared for the purpose of investigation for reduction of NO emission. It was intended to realize 2-stage combustion that is to keep fuel rich condition during early stage of combustion and fuel lean condition during next stage. The engine was tested on various conditions concerning exhaust gas emissions especially about NO emission and simultaneously fuel consumption rate. It was found that the engine with 2-stage combustion type piston emits significantly low NO at various speed and torque compared with conventional engines, but it raised points at issue in CO and smoke emissions with fuel consumption rate. The increasing of injection pressure on 2 stage combustion type diesel engine affects on CO and smoke emission considerably to reduce but slightly on NO to increase. The effect of 2-stage combustion was better at low speed than at high speed.

• 한국가스학회지
• /
• 제12권4호
• /
• pp.58-62
• /
• 2008

본 연구에서는 직렬 6기통 압축천연가스 엔진의 피스톤에 대한 3차원 모델링을 수행하여 정상상태에서의 온도분포 및 그에 따른 열응력과 변형을 예측하고, 이를 기존의 해석결과와 비교 검토를 통하여 피스톤의 유한요소해석의 기준을 구축하고자 한다. 또한 냉각시스템의 성능이 피스톤의 열부하에 미치는 영향을 평가하기 위하여 냉각수 온도의 변화에 따른 피스톤의 온도분포 및 열응력 분포 그리고 그에 따른 변형을 분석하였다. 분석결과 피스톤의 최고 온도는 크라운부의 중앙에서 나타났고, 피스톤의 크라운 하부에서 최대 열응력이 발생하였다.

• 대한기계학회논문집B
• /
• 제26권4호
• /
• pp.614-621
• /
• 2002

This study was performed to investigate the behavior of vapor phase of fuel mixtures with different piston bowl shapes(F, B and R-type) in a optically accessible engine. The images of liquid and vapor phases were captured in the motoring engine using exciplex fluorescence method. Fuel was injected into atmospheric nitrogen to prevent quenching phenomenon by oxygen. Injection pressure was 5.1MPa. Two dimensional spray fluorescence image of vapor phase was acquired to analyze spray behaviors and fuel distribution inside of cylinder. Four injection timings were set at BTDC 90$^{\circ}$, 80$^{\circ}$, 70$^{\circ}$, and 60$^{\circ}$. With a fuel injection timing of BTDC 90$^{\circ}$, fuel-rich mixture level in the center region was highest in a B-type piston. With a fuel injection timing of BTDC 60$^{\circ}$, R-type piston was best. R-type piston shape was suitable under enhanced swirl ratio and late injection condition and B-type piston shape was right in a weak swirl ratio. It was found that the piston bowl shape affected the mixture stratification inside of cylinder.

• Journal of Mechanical Science and Technology
• /
• 제17권12호
• /
• pp.2027-2033
• /
• 2003

The purpose of this study is to investigate the stratification of fuel vapor with different in-cylinder flow, piston cavity and injection timings in an optically accessible engine. Three different piston shapes that are F(Flat), B(Bowl) and R(Re-entrance) types were used. The images of liquid and vapor fuel were captured under the motoring condition using Laser Induced Exciplex Fluorescence technique. As a result, at early injection timing of 270 BTDC, liquid fuel was evaporated faster by tumble flow than swirl flow, where most of fuel vapor were transported by tumble flow to the lower region and both sides of cylinder for the F-type piston. At late injection timing of 90 BTDC, tumble flow appears to be moving the fuel vapor to the intake side of the cylinder, while swirl flow convects the fuel vapor to the exhaust side. The concentration of mixture in the center region was highest in the B-type piston, while fuel vapor was transported to the exhaust side by swirl flow in F and R-type pistons. At the injection timing of 60 BTDC, the R-type piston was better for stratification due to a relatively smaller bowl diameter than the others.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.915-920
• /
• 2001

This study was performed to investigate the behavior of vapor phase of fuel mixtures with different piston bowl shapes(F, B, and R-type) in a optically accessible engine. The images of liquid and vapor phases were captured in the motoring engine using exciplex fluorescence method. Fuel was injected into atmospheric nitrogen to prevent quenching phenomenon by oxygen. Injection pressure is 5.1MPa. Two dimensional spray fluorescence image of vapor phases was acquired to analyze spray behaviors and fuel distribution inside of cylinder. Four injection timings were set at BTDC $90^{\circ},\;80^{\circ},\;70^{\circ},\;and\;60^{\circ}$. With a fuel injection timing of BTDC $90^{\circ}$, fuel-rich mixture level in the center region was highest in a B-type piston. With a fuel injection timing of BTDC $60^{\circ}$, R-type piston was best. R-type piston shape was suitable under enhanced swirl ratio and late injection condition and B-type piston shape was right in a weak swirl ratio. It was found that the piston bowl shape affected the mixture stratification inside of cylinder.