• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2003년도 추계학술발표회
• /
• pp.91-94
• /
• 2003

A field pilot-scale demonstration of an enhanced SVE using hot air injection and extraction was conducted to remove diesel range compounds from subsurface soils at a site in J-city, Korea. The objective of demonstration was to evaluate field ISR by intrinsic microorganism after an application study of hot air-SVE technology and to calculate each first-order kinetic with soil temperature. TPH concentration of contaminated soil at the site was approximately 2, 000~11, 000 mg/kg (average 6, 900 mg/kg) with depths greater than 5 m bgs. The 1st-order reaction rate constants, k were 0.0438(@about5$0^{\circ}C$), 0.0564(@4$0^{\circ}C$), and 0.0685(@33$^{\circ}C$) d-1 respectively.

• 한국대기환경학회지
• /
• 제7권1호
• /
• pp.31-40
• /
• 1991

This study shows the correlation between $NO_x$ emission in the exhaust gas and various operation factors of dual fuel engine for Co-generation system. General tendency was shown that the thermal efficiency was lowered by the change of operation factors. However these were not confirmed on this experiment. Increasing T4 temperature (exhaust gas temperature at turbo-charger inlet) reduces $NO_x$ emission rate. The higher T4 temperature requires lower excess air as the excess air ratio is controlled by T4 temperature on gas mode operation. Another tendency was that $NO_x$ emission rate is reduced in case of increasing boost air temperature, quantity of pilot oil or bypassing flue gas through the exhaust gas boiler. The diameter of the fuel injection nozzle was changed smaller than design value and the injection timing was readjusted. Thus $NO_x$ emission rate could be reduced as retarding injection timing and changing hole diameter of fuel injection nozzle, however maxium engine out-put was decreased by changing fuel nozzle on the diesel mode operation.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2001년도 춘계학술대회 논문집
• /
• pp.187-191
• /
• 2001

In the paper, an approach to the development of the selective catalytic reduction process of NOx is presented. The reduction process can be efficiently controlled using a conventional combination of feed-forward and feed-back control structures. The aim of this paper is to test and verify an approach to the SCR process which is based on an industrial pilot plant of combustion and nitric oxide formation. The systems are based on measurements of a NOx removal ratio and the fuel flow rate, and NH$_3$slip which are usually available as a part of de-NOx control system.

• International Journal of Automotive Technology
• /
• 제8권2호
• /
• pp.155-163
• /
• 2007

The control of the fuel to be introduced into the combustion chamber under idling and low-load conditions is known to be a problem in Diesel engines, owing to the relatively small fraction of the full-load fuel needed under light loads. Thus, particular attention should be paid to the behavior of the injector with reference to short injection events. This work presents the results of an experimental campaign carried out with two different types of common rail injectors, a standard injector and a modified one. The latter, coming from a simple modification realized in a standard injector, exhibits linear behavior between injected fuel and solenoid energizing time in the field of short injections. A direct comparison of the two injection behaviors suggests a possible way to better control short or pilot injections.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 1999년도 정기총회 및 춘계 공동 학술발표회
• /
• pp.26-28
• /
• 1999

동절기 급격한 온도 저하로 인한 적용한계를 극복하기 위하여 composting 기술을 현장에 적용하여 적용 가능성을 검토하고 온도 변화에 따른 분해 특성을 검토하였다. 기초 실험을 통해 영양원과 유류분해 미생물의 첨가에 따른 분해 효율을 점검한 결과 초기 유효 미생물 (유류분해 미생물)의 농도가 낮고 영양원(N, P source)의 불균형으로 인해 영양원의 첨가와 유류분해 미생물을 동시에 투입하는 것이 바람직한 것으로 나타났으며, 동절기 낮은 온도를 극복하기 위해 퇴비를 투입한 Co-composting 기술은 주입된 퇴비의 영향으로 pile 내부의 온도가 30-40일 동안 중온상태를 유지하였으며, 제거효율은 91%로 나타났다. 따라서 유류 오염토양을 복원함에 있어서 동절기에도 별도의 시설투자 없이 효율적으로 유류를 분해시킬 수 있는 CO-Composting 기술의 적응 가능성이 확인되었으며, 난분해성 물질의 생물학적 분해에 있어서도 다양하게 적용될 수 있을 것으로 판단된다.

• Advances in Energy Research
• /
• 제8권3호
• /
• pp.175-184
• /
• 2022

The dual-fuel technology, which uses gaseous fuel as the main fuel and liquid as the pilot fuel, is an appealing technology for reducing the exhaust emissions. The current study proposes emission models based on ANFIS for a dual-fuel using producer gas (PG)-diesel engine. Emissions measurements were taken at different engine load levels and fuel injection timings. The proposed model predictions were examined using statistical methods. With R2 values in the range of 0.9903 to 0.9951, the established ANFIS model was found to be consistently robust in predicting emission characteristics. The mean absolute percentage deviate in range 1.9 to 4.6%, and mean squared error varies in range 0.0018 to 13.9%. The evaluation of the ANFIS model developed shows a reliable claim of intrinsic sensitivity, strength, and outstanding generalization. The presented meta-model can be used to simulate the engine's operation in order to create an efficient control tool.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.1-11
• /
• 2006

The aim in this study is to develop the combined EGR system with a non-thermal plasma reactor for reducing exhaust emissions and improving fuel economy in turbo intercooler ECU common-rail diesel engines. In this study, the characteristics of soot, CO and $CO_2$ emissions under four kinds of engine loads are experimentally investigated by using a four-cycle, four-cylinder, direct injection type, water-cooled turbo intercooler ECU common-rail diesel engine with a combined plasma exhaust gas recirculation(EGR) system operating at three kinds of engine speeds. The EGR and non-thermal plasma reactor system are used to reduce $NO_x$ emissions, and the non-thermal plasma reactor and turbo intercooler system are used to reduce soot and THC emissions. The plasma system is a flat-to-flat type reactor operated by a plasma power supply. The fuel is sprayed by pilot and main injections at the variable injection timing between BTDC $15^{\circ}$ and ATDC $1^{\circ}$ according to experimental conditions. It is found that soot emissions with increasing EGR rate are increased, but are decreased as the applied electrical voltage of the non-thermal plasma reactor is elevated at the same engine speed and load. Results also show that CO and $CO_2$ emissions are increased as EGR rate is elevated, and CO emissions are increased, but $CO_2$ emissions are decreased as the applied electrical voltage of the non-thermal plasma reactor is elevated at the same engine speed and load.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.111-120
• /
• 2014

The aim of this study is to develop an integrated urea-SCR catalytic filter system for reducing soot and $NO_X$ emissions simultaneously in diesel engines. In this study, the characteristics of exhaust emissions relative to reactive activation temperature under four kinds of engine loads are experimentally investigated by using a four-cycle, four-cylinder, direct injection type, water-cooled turbo intercooler ECU common-rail diesel engine with the integrated urea-SCR $MnO_2-V_2O_5-WO_3/TiO_2/SiC$ catalytic filter system operating at three kinds of engine speeds. The urea-SCR reactor is used to reduce $NO_X$ emissions, and the catalytic filter system is used to reduce soot emissions. The reactive activation temperature is very important for reacting a reducing agent with exhaust emissions. The reactive activation temperatures in this experiment is applied to 523, 573 and 623 K. The fuel is sprayed by the pilot and main injections at the variable injection timing between BTDC $15^{\circ}$ and ATDC $1^{\circ}$ according to experimental conditions. It is found that the $NO_X$ conversion rate is the highest as 83.9% at the reactive activation temperature of 523 K in all experimental conditions of engine speed and load, and the soot emissions shown by the average reduction rate of approximately 93.3% are almost decreased below 0.6% in all experimental conditions regardless of reactive activation temperatures. Also, the THC and CO emissions by oxidation reaction of Mn, V and Ti are shown in the average reduction rates of 70.3% and 38% regardless of all experimental conditions.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제10권4호
• /
• pp.45-53
• /
• 2005

본 연구의 목적은 실제 디젤유로 오염된 불포화 토양을 복원하기 위해 수행되었던 고온공기 주입 파일롯 테스트에서 토양온도 변화가 생분해 속도에 미치는 영향을 알아보고자 히는 것이었고, 이것을 토대로 현장 생분해 속도, 최적의 생분해 온도 및 1차 분해 속도 상수를 도출하고 총복원기간을 예측해 보았다. 실험은 과거 디젤유 누출 사고가 있었던 고농도 오염지역에 대해 토양의 온도별 현장 호흡률(in-situ respiration)을 약 10일 간격으로 측정하는 식으로 진행되었다. 적용된 복원공법은 고온공기를 주입/추출하여 1차적으로 오염된 디젤 성분을 휘발, 추출하고 이어서 토양의 잔열과 미생물 생분해를 이용하여 토양내 잔류 디젤을 제거하는 후속공정으로 이루어졌다. 토양온도 $26\sim60^{\circ}C$ 범위에서 산소소비속도는 $2.2\sim46.3%/day$ 값을 보였고 $32^{\circ}C$에서 가장 빠른 46.3%/day를 나타냈다. 산소소비속도를 기준으로 하여 계산한 0차반응 생분해 속도(biodegradation rate)는 $6.5\sim21.3mg/kg-day$ 이었고 역시 토양온도 $ 32^{\circ}C$ 에서 최대값을 보였고 그 이전과 이후는 각각 감소된 값을 나타냈다. 주기적으로 측정된 현장호흡률을 바탕으로 계산한 1차 분해속도 k는 몇가지 온도 범위에서 즉, $0.0027\;d^{-1}(@32.8^{\circ}C),\;0.0013\;d^{-1}(@41.1^{\circ}C)$ 그리고 $0.0006\;d^{-1}(@52.7^{\circ}C)$ 이었다. 토양의 초기 TPH 농도 대비목표 농도를 870 mg/kg으로 가정했을 경우 소요 복원기간은 $2\mu9$년 정도 소요되는 것으로 예측되었다.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제7권4호
• /
• pp.87-91
• /
• 2002

유류로 오염된 부지에 토양세정기법을 적용하기 위하여 실험실 규모의 컬럼실험을 통하여 pilot규모 현장 적용을 위한 설계인자 및 최적 운전조건을 규명하고자 적정 세척제 종류와 농도, 배합비 및 세정용액 주입유량을 고찰하였다. 회분식실험 결과 $POE_{14}$와 SDS(1:1)를 1%로 적용한 혼합계면활성제의 효율이 가장 우수하였다. 그러나 예비실험 결과, 음이온계 계면활성제인 SDS는 생분해능 저해 경향이 다소 있는 것으로 나타나 같은 농도에서 효율이 거의 유사하며, 생분해능이 우수한 $POE_{5}$와 $POE_{14}$ 혼합계면활성제를 이용하여 실험하였다. 선정된 혼합계면활성제를 적용하여 디젤 오염토양 세척능력에 대하여 검토한 결과 세척제 농도 l%까지는 효율이 증가하다가 1% 이상의 농도에서는 다시 감소하는 경향을 나타내었다. 또한, 계면활성제 배합비를 1:1로 혼합하였을 경우 세척효율이 가장 우수하였다. 따라서 $POE_{5}$와 $POE_{14}$(1:1) l% 혼합계면활성제를 세척제로 선정하였다. 컬럼실험 결과, 주입 flux가 클수록 세정 제거된 총 유류의 양이 증가하였으며, 같은 pore velum히 세정용액 통과 시에는 flux가 작을수록 제거효율이 우수하였다.