• Smart Structures and Systems
• /
• 제26권3호
• /
• pp.391-401
• /
• 2020

The present article reports the feasibility of the electrical energy generation from ambient low-frequency vibration using a piezoelectric material mounted on a bimorph cantilever beam actuator. A corresponding higher-order analytical model is developed using MATLAB in conjunction with finite element method under low-frequency with both damped and undamped conditions. An alternate model is also developed to check the material and dimensional viability of both piezoelectric materials (mainly focussed to PVDF and PZT) and the base material. Also, Genetic Algorithm is implemented to find the optimum dimensions which can produce the higher values of voltage at low-frequency frequencies (≤ 100 Hz). The delamination constraints are employed to avoid inter-laminar stresses and to increase the fracture toughness. The delamination has been done using a Teflon sheet sandwiched in between base plates and the piezo material is stuck to the base plate using adhesives. The analytical model is tested for both homogenous and isotropic material characteristics of the base material and extended to investigate the effect of the different geometrical parameters (base plate dimensions, piezo layer dimensions and placement, delamination thickness and placement, excitation frequency) on the model responses of the bimorph cantilever beam. It has been observed that when the base material characteristics are homogenous, the efficiency of the model remains higher when compared to the condition when it is of isotropic material. The necessary convergence behaviour of the current numerical model has been established and checked for the accuracy by comparing with available published results. Finally, using the results obtained from the model, a prototype is fabricated for the experimental validation via a suitable circuit considering Glass fibre and Aluminium as the bimorph material.

• 대한기계학회논문집B
• /
• 제24권8호
• /
• pp.1112-1118
• /
• 2000

The objective of this study is to increase lift and decrease drag of an airfoil at high angles of attack by delaying flow separation with piezo-ceramic actuators. The airfoil used is NACA 0012 and its chord length is 0.3m. An experiment is performed at the freestream velocity of 15m/s at which the Reynolds number based on the chord length is $2{\times}10^5$. Seven rectangular actuators are attached to the airfoil surface and move up and down based on the electric signal. Drag and lift are measured using an in-house two-dimensional force-balance and the surface pressures are also measured. At the attack angle of $16^{\circ}$, the separation point is delayed downstream due to momentum addition induced by the movement of the actuators. Lift is increased by 10%, drag is reduced by 37%, and the efficiency is increased up to 170%. The flow fields with and without control are visualized using the smoke-wire and tuft techniques.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.414-417
• /
• 2001

Recently, developments of device using characteristics of ceramics as a new technical material is in progress. While doing so, Ultrasonic motor which is a part of research & development of piezo-actuator by piezo-effects is being used in the various applications. So, we fabricated a flat-type $L_{1}-B_{8}$ mode Ultrasonic motor and measured the operation characteristics of its. The size of USM is 80*20*1.5[$mm^{3}$](length*width*thickness) and is constructed with stator by piezo-ceramics and stainless elastic body and rotator by bearings. As results of experiments, the fastest speed of revolution(v), the maximum torque(T) and the efficiency( $\eta$ ) were 37.5[cm/sec], 5.0[ $mN{\cdot}m$ ] and 1.17[%] respectively when 27.9[kHz], 150[gf], 50[V] were applied. So, we think this $flat-type_{1}-B_{8}$ mode Ultrasonic motor is able to be used for applications in forwarding device of a paper or electric card and so on.

• Smart Structures and Systems
• /
• 제8권3호
• /
• pp.275-302
• /
• 2011

This is a review paper on mathematical modeling of actively controlled piezo smart structures. Paper has four sections to discuss the techniques to: (i) write the equations of motion (ii) implement sensor-actuator design (iii) model real life environmental effects and, (iv) control structural vibrations. In section (i), methods of writing equations of motion using equilibrium relations, Hamilton's principle, finite element technique and modal testing are discussed. In section (ii), self-sensing actuators, extension-bending actuators, shear actuators and modal sensors/actuators are discussed. In section (iii), modeling of thermal, hygro and other non-linear effects is discussed. Finally in section (iv), various vibration control techniques and useful software are mentioned. This review has two objectives: (i) practicing engineers can pick the most suitable philosophy for their end application and, (ii) researchers can come to know how the field has evolved, how it can be extended to real life structures and what the potential gaps in the literature are.

• 대한기계학회논문집A
• /
• 제24권6호
• /
• pp.1390-1397
• /
• 2000

This paper presents the multi-channel active vibration control of a flexible plate of the acoustically loaded enclosure. The flexible plate was excited acoustically with sinusoidal and white noise input. The control was performed by two piezo ceramic actuators and two accelerometers. The experimental results were compared with the single channel control results. In the case of white noise input, 20 dB of vibration reduction was achieved below 300Hz frequency range. The experimental results demonstrate that multi-channel filtered-x LMS algorithm is effective than single-channel filtered-x LMS algorithm in active vibration control of plate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1332-1335
• /
• 2003

This paper presents the enhancement of oxygen transfer efficiency using the vibrating intravascular lung assist device (VIVLAD) in in-vitro experiments for patients having chronic respiratory problems. The test section was a cylinder duct with the inner diameter of 30 mm. The flow rate was controlled by the pump and monitored by a built-in flow meter. The vibration apparatus was composed of a piezo-vibrator, a function generator. and a power amplifier. The direction of vibration was radial to the fluid flow. Gas flow rates of up to 6 l/min through the 120-cm-Jong hollow fibers have been achieved by exciting a piezo-vibrator. The output of PVDF sensor were investigated by various frequencies in VIVLAD. The experimental results showed that VIVLAD would be enhance oxygen transfer efficiency.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.127-132
• /
• 2001

In this paper, transmitted sound reduction performance of smart panels is studied according to different piezoelectric materials with piezoelectric shunt damping. Peizo-damping is implemented by using a newly proposed tuning method. This method is based on electrical impedance model and maximizing the dissipated energy at the shunt circuit. By measuring the electrical impedance at the piezoelectric patch bonded on a structure, an equivalent electrical model is constructed near the system resonance frequency. After shunting elements are connected to the equivalent circuit, the shunt parameters are optimally searched based on the criterion of maximizing the dissipated energy at the shunt circuit. Transmitted sound reduction performance is compared according to different piezoelectric materials with peizo-damping. Two piezoelectric materials are selected: PZT-5 and QuickPack IDE actuator. When resonant shunt circuit is considered, the use of PZT-5 exhibited the good sound reduction performance.

• 한국공작기계학회논문집
• /
• 제14권4호
• /
• pp.55-60
• /
• 2005

In this study, vibration control of the enclosed plate which is typical two dimensional structure are performed by using intelligent control method and piezo ceramic as an actuator attached at the plate. The characteristics of the plate with piezo ceramic are examined to identify the natural frequencies. Then, the plate is controlled under the sinusoidal excitation by acoustic source and the reduction level of vibration is examined via frequency response and time sequence. The control result shows the effect of the intelligent control method as a control scheme compared with that of the previous filtered-X LMS algorithm.

• 설비공학논문집
• /
• 제19권5호
• /
• pp.411-417
• /
• 2007

This study has been conducted to investigate pumping characteristics of diffuser/nozzle based piezoelectric micropumps. The micropumps include a piezo disk (an actuator), a chamber and a set of diffuser and nozzle. Flow in the current micropumps is controlled by a set of diffuser and nozzle, not by a nap valve. The diffuser/nozzle based micropumps are more reliable in operation and are easier in manufacturing than the flap valve based micropumps. The flow rates of the piezoelectric micropumps have been closely analyzed with a numerical calculation. It has been found that the positions of the inlet and outlet of the micropump can influence the performance of the diffuser/nozzle based piezoelectric micropumps. This study may provide fundamental understanding for the design and analysis of the piezoelectric micropumps.

• Smart Structures and Systems
• /
• 제6권2호
• /
• pp.167-182
• /
• 2010

An adaptronic strut for machine tools with parallel kinematics for compensation of the influence of geometric errors is introduced. Implemented within the strut is a piezoelectric sensor-actuator unit separated in function. In the first part of this contribution, the functional principle of the strut is presented. For use of one piezoelectric transducer as both, sensor and actuator as so-called self-sensing actuator, the acquisition of the sensing signal while actuating simultaneously using electrical bridge circuits as well as filter properties are examined. In the second part the control concept developed for the adaptronic strut is presented. A co-simulation model of the strut for simulating the controlled multi-body behavior of the strut is set-up. The control design for the strut as a stand-alone system is tested under various external loads. Finally, the strut is implemented into a model of the complete machine tool and the influence of the controlled strut onto the behavior of the machine tool is examined.