• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.6
• /
• pp.128-135
• /
• 2003

This study is performed to examine the physical and mechanical properties of concrete using recycled aggregate and industrial by-products. The test results show that the unit weight, compressive and flexural strength, ultrasonic pulse velocity and dynamic modulus of elasticity are decreased with increasing the content of recycled aggregate. But, the absorption ratio is increased with increasing the content of recycled aggregate. The unit weight is 2,237∼2,307 kg/$\textrm{m}^3$, the absorption ratio is 2.96∼4.12%, the compressive strength is 415∼532 kgf/$\textrm{cm}^2$, the flexural strength is 75∼96 kgf/$\textrm{cm}^2$, the ultrasonic pulse velocity is 4,350∼4,949 m/s and the dynamic modulus of elasticity is $390\times10^3\;∼\;465\times10^3$ kg f/$\textrm{cm}^2$, respectively These recycled aggregate concrete can be used for high strength concrete.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11b
• /
• pp.118-121
• /
• 2005

The acoustical performance of porous materials is determined by their seven or more macroscopic physical properties. However, it is not easy to measure all these properties in many cases. Furthermore, the measurement is compels engineers to spend much times. The effect of each property on the normal incidence absorption coefficient and normalized surface impedance was studied to estimate the properties of porous materials by numerical method. According to the investigation, Properties of porous materials are divided into several groups and estimated by each group. This paper is focused on the estimation procedure of porous materials by the numerical method.

• Explosives and Blasting
• /
• v.22 no.2
• /
• pp.45-54
• /
• 2004

Samples examined in this study were acquired from Machun building stone, Dukwoo building stone in Kyungnam province The aim of this study is to examine physical features of Machun rock from specific gravity, porosity. absorption, point load test. triaxial compressive test, Brazilian test, petrology test, and chemical analysis test.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.97-100
• /
• 1994

The present paper is devoted to the physical and electrical characteristics of N-docosyl- quinolinium-TCNQ films compared with the films doped with I$_2$. Iodine affects the degree of charge transfer and the conductivity of the films. The UV-visible absorption spectra of the film doped with I$_2$ shows that the peak of I$_3$ which had electronic transition at 300∼350nm and (TCNQ-)$_2$ dimer absorption disappered. The in-plane electrical conductivity of the films doped with I$_2$ were 1.4${\times}$10$\sub$-6/S/cm, which is two orders of magnitude higher conductivity than undoped LB films. The film structural difference between Y and Z-type may cause the conductivity. Another possible reasons of the structural difference was the overlapping TCNQ anion radical in LB films.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.51 no.1
• /
• pp.21-26
• /
• 2009

This study was performed to evaluate the physical and mechanical properties of concrete using waste activated carbon. Materials used were ordinary portlant cement, crushed coarse aggregate, natural fine aggregate, waste activated carbon, and superplasticizer. The substitution ratios of waste activated carbon were 0,1,2,3,4,5,6,7,8,9 and 10%. The unit weight was decreased and water absorption ratio was increased with increasing the waste activated carbon content, respectively. When the substitution ratio of waste activated carbon was 3%, compressive strength, flexural strength and dynamic modulus of elastisity were more higher than that of the ordinary portland cement (OPC), and it was decreased with increasing the waste activated carbon content, respectively. The most effective contents of waste activated carbon was 2% in performance and 4% in practical use Accordingly, waste activated carbon can be used for concrete material.

• Fashion & Textile Research Journal
• /
• v.13 no.1
• /
• pp.130-134
• /
• 2011

In the study, the physical properties of the raw sample, non-circular(+ type) DTY yarn(50d level) with absorption and quick-dry function, were examined before and after being twisted(1000T/M). The results are as follows: The shrinkage of non-cricular(+type) DTY yarn(50d/36f) at $180^{\circ}$ was about 6-7% with twisted samples, but the samples without twisting went 8 to 10%. The elongation of the non-twisted and twisted samples at $180^{\circ}$ and 30-minute treatment time reached 50% and 40%, respectively. The tenacity of non-cricular(+type) DTY yarn(50d/36f) was affected less by treatment temperature in the twisted condition.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05b
• /
• pp.141-144
• /
• 2005

This paper reports the results of experimental study on the effect of an amount of mortar attached to the surface of original aggregate on the physical properties of recycled aggregates such as specific gravity, and water absorption. An amount of attached mortar was evaluated by hydrochloric acid precipitation method. Test results indicated that a water absorption of recycled aggregates was proportional to the amount of mortar attached to the original aggregate.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.22 no.6
• /
• pp.609-609
• /
• 1998

This paper surveys the effect of rice straw ash solution to the physical properties of Sappan Wood dyeing fabrics. In the quantitative analysis of rice straw ash solution, the quantities of absorbed ingredients in fabrics were increased by bath pull treatment but the amount of absorption(K/S value) was increased by bath pH4.5 treatment. This is related to the metal ion. Among the metal ion, effect of Fe iou and Al ion were related. In case added extracted dye solution to mordants, the color dye solution became dark and increased reddish. The changes of mechanical properties of fabrics tensile resilience, bending rigidity(B), compressional resilience(RC) were increased. Generally mechanical properties were increased by rice straw ash solution treatment, specially bath pH9 treatment. Rice straw ash solution treatment of dyeing fabrics made the improvement in tensile strength and elongation and in the amount of absorption, dye ability, color fastness, mechanical properties, tensile strength, elongation.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.22 no.6
• /
• pp.699-705
• /
• 1998

This paper surveys the effect of rice straw ash solution to the physical properties of Sappan Wood dyeing fabrics. In the quantitative analysis of rice straw ash solution, the quantities of absorbed ingredients in fabrics were increased by bath pull treatment but the amount of absorption(K/S value) was increased by bath pH4.5 treatment. This is related to the metal ion. Among the metal ion, effect of Fe iou and Al ion were related. In case added extracted dye solution to mordants, the color dye solution became dark and increased reddish. The changes of mechanical properties of fabrics tensile resilience, bending rigidity(B), compressional resilience(RC) were increased. Generally mechanical properties were increased by rice straw ash solution treatment, specially bath pH9 treatment. Rice straw ash solution treatment of dyeing fabrics made the improvement in tensile strength and elongation and in the amount of absorption, dye ability, color fastness, mechanical properties, tensile strength, elongation.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.3
• /
• pp.96-104
• /
• 1997

The objective of this research project was to develop the wooden footpath block to reuse of wood waste. Some physical and mechanical properties of the wooden block such as water absorption, thickness swelling, modulus of rupture, internal bond, density profile and impact resistance were studied. Water absorption and thickness swelling of the wooden block were greatly reduced when the wooden block was pressed inside the forming device than by conventional hot pressing. Also, Modulus of rupture and internal bond of the wooden block were increased greatly when the pressing was completed inside the forming device. The density profile of the wooden block was improved up to 93.5%, minimum to average density ratio. The wooden block manufactured in this study have excellent physical and mechanical prperties in comparison with existing wood based materials. So, these wooden blocks are applicable to footpth block or other exterior members.