• Tribology and Lubricants
• /
• v.34 no.6
• /
• pp.292-299
• /
• 2018

The objective of this research is to investigate the impact of engine oil aging on PM(Particulate Matter), exhaust gases, and DPF. It is widely known that the specification of a lubricant and its consumption in an ICE considerably influences the release of regulated harmful emissions under normal engine operating conditions. Considering DPF clogging phenomena associated with lubricant-derived soot/ash components, a simulated aging mode is designed for DPF to facilitate engine dynamometer testing. A PM/ash accumulation cycle is developed by considering real-world engine operating conditions for the increment of engine oil consumption and natural DPF regeneration for ash accumulation. The test duration for DPF aging is approximately 300 h with high- and low-SAPs engine oils. Detailed engine lubricant properties of new and aged oils are analyzed to evaluate the effect of engine oil degradation on vehicle mileage. Furthermore, physical and chemical analyses are performed using X-CT, ICP, and TGA/DSC to quantify the engine oil contribution on the PM composition. This is achieved by sampling with various filters using specially designed PM sampling equipment. Using high SAPs engine oil causes more PM/ash accumulation compared with low SAPs engine oils and this could accelerate fouling of the EGR in the engine, which results in an increase in harmful exhaust gas emissions. These test results on engine lubricants under operating conditions will assist in the establishment of regulated and unregulated toxic emissions policies and lubricant quality standards.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.153-161
• /
• 1998

The knock in a spark ignition engine has been investigated to avoid the damage to the engine and unpleasant feeling caused by the pressure waves propagating across the combustion chamber. Knock intensity and knock onset angle were used as physical parameters to quantify the knock characteristics. The knock intensity is defined as a peak to peak value of the bank pass filtered combustion pressure signal and the knock onset angle is determined as the crank angle at which this signal exceeded the threshold level on each cycle. The cyclic variation of knock in four valve single cylinder engine was investigated with these two parameters. The location of autoignition was also examined by ion probes in the cylinder head gasket and squish region in the combustion chamber. For this measurement, a single cylinder engine was modified to accept the pressure transducer, 18 ion probes in the squish region and 8 ion probes in the specially designed PCB (Printed \ulcornerCircuit Board) cylinder head gasket.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.24 no.1
• /
• pp.30-35
• /
• 1988

An electrical power generation system driven by main engine shaft, briefly SG system for middle or small size fishing boat is studied experimently. In the SG system, power transmission is performed by a variable displacement hydraulic pump driven by the main engine and a constant displacement hydraulic motor. It was verified that the SG system enabled the generation of electrical power with constant frequency regardless main engine speed. In the SG system, setting reference frequency, sensing generator output frequency and setting controller parameters are performed by performed by programming in a microcomputer, so a countermeasure for physical situations of control object is very easy. Futhermore, the SG system has following features; low initial installation cost, wide freedom of installation in engine room, advantage of application in existing ships, especially fishing boat with hydraulic fishing equipments.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.846-851
• /
• 2001

For the successful development of the main engine of KSR(Korea Sounding Rocket)-III, Korea Aerospace Research Institute(KARI) carried out the experimental study on the subscale model engines. Several types of engines were tested on the Small Liquid Rocket Engine Test Facility. One of the typical test results of a Sub. engine(Sub. Mod.3) is presented here. It uses the Jet A-1 as fuel, liquid oxygen as oxidizer, and Tri-Ethyl Aluminium(TEA1) as ignition agent. The gas pressure feed system is adopted as a feeding mechanism and the design chamber pressure is 200psia. The physical phenomena are described in three regimes(ignition, transient, and steady state) with the pressure, thrust, flowrate and image data. And the pressure oscillation is analyzed in Fourier domain (<500Hz). Then we conclude that in this experiment, the engine shows the characteristic low frequency of 80Hz and it is stable for that frequency of pressure oscillation.

• Tribology and Lubricants
• /
• v.22 no.5
• /
• pp.260-268
• /
• 2006

The dielectric constants of used gasoline engine oils were obtained at a few temperatures and a frequency. Through analyzing the characteristics of dielectric constant, the related correlation between the changes in dielectric constants of oil and the degree of oil deterioration is going to be found. The dielectric constant was calculated using cross capacitances measured by a sensor tube. As results of the measurement of the fresh engine oil's dielectric constant, it was found that the value of dielectric constant was set down below $60^{\circ}C$ regardless changing frequency. Further, above 6 kHz, the dielectric constant was set down even if temperature was above $100^{\circ}C$ Therefore, for the measurement of used oils, it was selected the frequency of 6 kHz,,and the temperature of $80^{\circ}C$ preventing a certain ionic-conduction effects on the measured dielectric constant and the evaporation of a certain fluid mixed with engine oil. Specially, the effects of the mixing fluid like coolant, water and fuel on the fresh engine oil's dielectric constant were studied. It was found that the oil mixed with coolant showed the highest value, next water, and the lowest fuel. As results of the measurement of the used engine oil's dielectric constant, it was found that the possible changed rate of the used engine oil's dielectric constant based on the warning limit for engine oil in service was below 4% for gasoline engine oil.

• Tribology and Lubricants
• /
• v.22 no.5
• /
• pp.290-300
• /
• 2006

The dielectric constants of used diesel engine oils were obtained at a few temperatures and a frequency. Through analyzing the characteristics of dielectric constant, the related correlation between the changes in dielectric constants of oil and the degree of oil deterioration is going to be found. The dielectric constant was calculated using cross capacitances measured by a sensor tube. As results of the measurement of the fresh engine oil's dielectric constant, it was found that the value of dielectric constant was set down below $60^{\circ}C$ regardless changing frequency. Further, above 6 kHz, the dielectric constant was set down even if temperature was above $100^{\circ}C$. Therefore, for the measurement of used oils, it was selected the frequency of 6 kHz, and the temperature of $80^{\circ}C$ preventing a certain ionic-conduction effects on the measured dielectric constant and the evaporation of a certain fluid mixed with engine oil. Specially, the effects of the mixing fluid like coolant, water and fuel on the fresh engine oil's dielectric constant were studied. It was found that the oil mixed with coolant showed the highest value, next water, and the lowest fuel. As results of the measurement of the used engine oil's dielectric constant, it was found that the possible changed rate of the used engine oil's dielectric constant based on the warning limit for engine oil in service was below 10% for diesel engine oil.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.3
• /
• pp.83-94
• /
• 2000

A systematic humidity correction technique that can be used for any type of engine control mode is developed to predict the variation of engine performance due to inlet humidity. Limitation of conventional method is rot identified and then, a new method is proposed to take into account the humidity effects on each engine component characteristics and to find the variation of equilibrium running point through a re-match process between the components with a given engine control variable depending on the humidity of inlet. Comparisons are made between two methods for a single spool gas turbine engine, and it was found that the conventional method leads to invalid correction when a physical variable such as rotational speed is controlled for engine operation in humid environment. It was also found that the accuracy of the conventional method depends on the engine control mode and the engine configuration whereas the proposed method can be used for any type of engine control mode and engine configuration.

• Journal of Power System Engineering
• /
• v.21 no.3
• /
• pp.66-73
• /
• 2017

In order to identify the design parameters of a hydraulic engine mount with a nonlinear characteristics, an experimental method has been used generally. The method takes a considerable time and expense because of preparing an experimental apparatus, conducting a test, and analyzing results. Therefore, this paper presents a simple method to identify the design parameters of a cylindrical hydraulic engine mount, and optimize the design parameters. The physical model and mathematical equations of the mount were derived, and values of the design parameters of the mount were identified by optimization method with minimizing difference between the analytical results with the equations and the experimental results. This method is more simpler than the conventional experiment method and identify successfully the design parameters. In addition, the technique can optimize the design parameters of the mount to improves the isolation performance of the mount.

• Proceedings of the IEEK Conference
• /
• 2009.05a
• /
• pp.156-158
• /
• 2009

A graphic simulator is efficient to see what will happen to the target robot. But it is not exactly same as the real world. Because there are so many physical laws to be concerned. In this paper, we propose a simulator with physics engine to create motions for quadruped robot. It is not only to show more real simulations but also to be more efficient for teaching motions to quadruped robot. To solve the quadruped robot's dynamics or inverse kinematics, It takes much times and hard effort. Using physics engine make it easy to setup motions without calculating inverse kinematics or dynamics.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.4
• /
• pp.534-542
• /
• 1998

In this paper a simulation model for the powertrain control of gasoline engines with automatic transmission is presented. A modular programming approach has been pursued and the MATLAB/SIMULINK has been utilized as the programming environment. The engine/transmission system is analyzed in the object-oriented fashion whereby easy transferal of the modules, which represent physical parts or analysis subsystems, is guaranteed. Some mathematical models are adopted from the literature to compare the simulation results with the model and the experimental results in the literature. It is expected that the whole program or individual module constructed in this paper are useful for the automotive engineers in designing a new engine/transmission system and/or in modifying parts of existing systems.