• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.5 s.170
• /
• pp.175-180
• /
• 2005

The application of focused ion beam (FIB) technology in micro/nano machining has become increasingly popular. Its use in micro/nano machining has advantages over contemporary photolithography or other micro/nano machining technologies such as small feature resolution, the ability to process without masks and being accommodating for a variety of materials and geometries. In this research, fabrication of micro plasma electrode was carried out using FIB. The one of problems of FIB-sputtering is the redeposition of material including Ga+ ion source during sputtering process. Therefore the effect of the redeposition was verified by EDX. And the micro plasma electrode of copper was fabricated by FIB.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.11
• /
• pp.992-998
• /
• 2009

We investigated the influence of organic solvents on the droplet properties of 6,13-bis (triisopropylsilylethynyl) pentacene (TIPS-pentacene), which was used for semiconductor of organic thin film transistors (OTFTs) and deposited by ink jet printing. From the result of the investigation, the conditions of a suitable solvent is that boiling point should be above $200^{\circ}C$ to reduce coffee stain and the surface tension above 32 dyn/cm to decrease the droplet size. Consequently, we selected tetralin which have a high boiling point ($207^{\circ}C$) and high surface tension (34.3 dyn/cm) as the solvent for TIPS-pentacene, and applied it to OTFTs. In fabrication process the conventional bank process employing photolithography and etching process was replaced by ink jet printed bank process, resulting in simplifying the process. Especially, polyvinylphenol was used for the bank, and the high hydrophobicity could improve the confinement of TIPS molecules inside the bank, enhancing the performance over the conventional hydrophilic polyvinylalcohol bank. The mobility was $0.18\;cm^2/Vs$, current on/off ratio $2.09{\times}10^5$, subthreshold slope 0.42 V/dec, and off state current $0.049\;pA/{\mu}m$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.155-158
• /
• 2007

Printed organic thin-film transistor(OTFT) to use as a switching device for an organic light emitting diode(OLED) were fabricated in the microcontact printing and direct printing processes at room temperature. The gate electrodes($5{\mu}m$, $10{\mu}m$, and $20{\mu}m$) of OTFT was fabricated using microcontact printing process, and source/drain electrodes ($W/L=500{\mu}m/5{\mu}m$, $500{\mu}m/10{\mu}m$, and $500{\mu}m/20{\mu}m$) was fabricated using direct printing process with hard poly(dimethylsiloxane)(h-PDMS) stamp. Printed OTFT with dielectric layer was formed using special coating system and organic semiconductor layer was ink-jet printing process. Microcontact printing and direct printing processes using h-PDMS stamp made it possible to fabricate printed OTFT with channel lengths down to $5{\mu}m$, and reduced the process by 20 steps compared with photolithography. As results of measuring he transfer characteristics and output characteristics of OTFT fabricated with the printing process, the field effect characteristic was verified.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.10
• /
• pp.546-550
• /
• 2004

Two fabrication approaches are proposed to planarize the sacrificial layer over hollow structures. One is the photoresist filling method that makes use of photolithography, thermal curing and plasma ashing. The other is the lamination method that is applying pressure and temperature to the organic film over the hollow structures. The fabrication results are compared with those of CMP process. Trenches and cavities with various dimensions have been made for the porposed process. Upon measuring the planarization levels, they are dependent on planarization methods and the geometrical size of hollow structures. The photoresist filling method is so strongly dependent on the width and depth of trenches that we have problems to use it for large dimensional trenches. To the contrary, the flatness of sacrificial layer over the trenches was found to be almost independent of trench dimensions for the lamination method. A CMP process shows the most excellent results, but the fabrication is complicated and the access to it is not so easy. It is important to choose the proper planarization method by considering the required flatness levels, materials to be planarized, and connection between the planarization step and the previous or the following process of it.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.71-71
• /
• 2003

Hot embossing has been widely accepted as an alternative to photolithography in generating patterns on polymeric substrates. The optimization of embossing process should be accomplished based on polymer substrate materials. In this paper, the effect of polymer substrates on nano scale hot embossing process was studied. Silicon molds with nano size patterns were fabricated by e-beam direct writing. Molds were coated with self-assembled monolayer (SAM) of (1, 1, 2.2H -perfluorooctyl)-trichlorosilane to reduce the stiction between mold and substrates. For an embossing, pressure of 55, 75 bur, embossing time of 5 min and temperature of above transition temperature were peformed. Polymethylmethacrylates (PMMA) with different molecular weights of 450,000 and 950,000, MR-I 8010 polymer (Micro Resist Technology) and polyaliphatic imide copolymer were applied for hot embossing process development in nano size. These polymers were spun coated on the Si wafer with the thickness between 150 and 200 nm. The nano size patterns obtained after hot embossing were observed and compared based on the polymer properties by scanning electron microscopy (SEM). The imprinting uniformity dependent on the Pattern density and size was investigated. Four polymers have been evaluated for the nanoimprint By optimizing the process parameters, the four polymers lead to uniform imprint and good pattern profiles. A reduction in the friction for smooth surfaces during demoulding is possible by polymer selection.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.11
• /
• pp.2056-2060
• /
• 2007

A successful combination of “oxygen-assisted chemical vapor deposition (CVD) process” and Co catalyst nanoparticles to grow highly pure single walled carbon nanotubes (SWNTs) was demonstrated. Recently, it was reported that addition of small amounts of oxygen during CVD process dramatically increased the purity and yield of carbon nanotubes. However, this strategy could not be applied for discrete Fe nanoparticle catalysts from which appropriate yields of SWNTs could be grown directly on solid substrates, and fabricated into field effect transistors (FETs) quite efficiently. The main reason for this failure is due to the carbothermal reduction which results in SiO2 nanotrench formation. We found that the oxygen-assisted CVD process could be successfully applied for the growth of highly pure SWNTs by switching the catalyst from Fe to Co nanoparticles. The topological morphologies and p-type transistor electrical transport properties of the grown SWNTs were examined by using atomic force microscope (AFM), Raman, and from FET devices fabricated by photolithography.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.3
• /
• pp.181-187
• /
• 2014

Micro patterns are used to maximize the performance and efficiency of the product in many industries such as energy, display, printing, biology, etc. Nowadays, the fabrication technology for micro patterns has been developed in various ways such as photolithography, laser machining, electrical discharge machining and mechanical machining. Recently, mechanical machining the size of smaller than 1 micrometer could be tried, because the technology related to the machining was developed brilliantly. This paper shows the experiments using cutting processes in order to fabricate the micro pattern. Micro patterns of the size of several micrometers were machined by the diamond tools of two different shape, the deformation and generation of burr were investigated.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.1
• /
• pp.138-144
• /
• 2008

Micro-machining of a brittle material such as glass, silicon, etc., is important in micro fabrication. Particularly, micro-abrasive jet machining (${\mu}-AJM$) has become a useful technique for micro-machining of such materials. The ${\mu}-AJM$ process is mainly based on the erosion of a mask which protects brittle substrate against high velocity of micro-particle. Therefore, fabrication of an adequate mask is very important. Generally, for the fabrication of a mask in the ${\mu}-AJM$ process, a photomask based on the semi-conductor fabrication process was used. In this research a rapid mask fabrication technology has been developed for the ${\mu}-AJM$. By scanning the focused UV laser beam, a micro-mask pattern was fabricated directly without photolithography process and photomask. Two kinds of mask patterns were fabricated using SU-8 and photopolymer (Watershed 11110). Using fabricated mask patterns, abrasive-jet machining of Si wafer were conducted successfully.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.8
• /
• pp.47-54
• /
• 2012

In this paper, we have fabricated the Schottky diode for THz applications by heterogeneous resist patterning method. The Schottky diode was developed using electron beam lithography and photolithography to connect the anode and the anode pad for a simple process. The measured performance of developed Schottky diode are $11.2{\Omega}$ of series resistance, 25.96 fF of junction capacitance, 1.25 of ideality factor and 547.6 GHz of cut-off frequency.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.375.2-375.2
• /
• 2016

그래핀(Graphene)은 원자 한 층 두께의 얇은 특성에 기인하여 우수한 투과도(~97.3%)를 나타내며, 높은 전자 이동도($200,000cm^2V^{-1}s^{-1}$)로 인하여 전기 전도도가 우수한 2차원 전자소재이다. 또한 유연하고 우수한 기계적 물성을 가지고 있어 실제로 다양한 소자에서 활용되고 있다. 그래핀을 이용하여 다양한 소자로 응용하기 위한 과정 중 하나인 포토리소그래피 공정(Photolithography process)은 원하는 패턴을 만들기 위해 제작하고자 하는 기판 위에 포토레지스트(Photoresist)를 코팅하는 과정을 거치게 된다. 하지만 이러한 과정은 소자 제작에 있어서 포토레지스트 잔여물을 남기게 된다. 그래핀 위에 남은 포토레지스트 잔여물은 그래핀의 우수한 전기적 특성을 저하시켜 소자특성에 불이익을 주게 된다. 본 연구에서는 수소 플라즈마를 이용하여 그래핀 위에 남은 중합체(Polymer) 잔여물을 제거한다. 사용한 그래핀은 화학 기상 증착법(Chemical vapor deposition)을 이용하여 성장시켰으며, PMMA(Poly(methyl methacrylate))를 이용하여 이산화규소(silicon dioxide) 기판에 전사하였다. 그래핀의 손상 없이 중합체 잔여물을 제거하기 위해 플라즈마 처리시간을 15초부터 1분까지 늘려가며 연구를 진행하였으며, 플라즈마 처리 시간에 따른 중합체 잔여물의 제거 정도와 그래핀의 보존 여부를 확인하기 위해 라만 분광법(Raman spectroscopy)과 원자간력현미경(Atomic force microscopy)을 사용하였다. 본 연구 결과를 통해 간단한 플라즈마 처리로 보다 나은 특성의 그래핀 소자를 얻게 됨으로써, 향상된 특성을 가진 그래핀 소자로 산업적 응용 가능성을 높일 수 있을 것이라 생각된다.