• Journal of the Korean Vacuum Society
• /
• v.17 no.4
• /
• pp.311-316
• /
• 2008

Since the presence of the chemical impurities and defect at surfaces and interfaces greatly influence the properties of various semiconductor devices, an unambiguous chemical characterization of the metal and semiconductor surfaces become more important in the view of the miniaturization of the devices toward nano scale. Among the various conventional surface characterization tools, Electron-induced Auger Electron Spectroscopy (EAES), X-ray Photoelectron Spectroscopy (XPS) and Secondary Electron Ion Mass Spectroscopy (SIMS) are being used for the identification of the surface chemical impurities. Recently, a novel surface characterizaion technique, Positron-annihilation induced Auger Electron Spectroscopy (PAES) is introduced to provide a unique method for the analysis of the elemental composition of the top-most atomic layer. In PAES, monoenergetic positron of a few eV are implanted to the surface under study and these positrons become thermalized near the surface. A fraction of the thermalized positron trapped at the surface state annihilate with the neighboring core-level electrons, creating core-hole excitations, which initiate the Auger process with the emission of Auger electrons almost simultaneously with the emission of annihilating gamma-rays. The energy of electrons is generally determined by employing ExB energy selector, which shows a poor resolution of $6{\sim}10eV$. In this paper, time-of-flight system is employed to measure the electrons energy with an enhanced energy resolution. The experimental result is compared with simulation results in the case of both linear (with retarding tube) and reflected TOF systems.

• Korean Journal of Materials Research
• /
• v.25 no.8
• /
• pp.391-397
• /
• 2015

NiO catalysts/$Al_2O_3$/FeCrAl alloy foam for hydrogen production was prepared using atomic layer deposition (ALD) and subsequent dip-coating methods. FeCrAl alloy foam and $Al_2O_3$ inter-layer were used as catalyst supports. To improve the dispersion and stability of NiO catalysts, an $Al_2O_3$ inter-layer was introduced and their thickness was systematically controlled to 0, 20, 50 and 80 nm using an ALD technique. The structural, chemical bonding and morphological properties (including dispersion) of the NiO catalysts/$Al_2O_3$/FeCrAl alloy foam were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, field-emission scanning electron microscopy and scanning electron microscopy-energy dispersive spectroscopy. In particular, to evaluate the stability of the NiO catalysts grown on $Al_2O_3$/FeCrAl alloy foam, chronoamperometry tests were performed and then the ingredient amounts of electrolytes were analyzed via inductively coupled plasma spectrometer. We found that the introduction of $Al_2O_3$ inter-layer improved the dispersion and stability of the NiO catalysts on the supports. Thus, when an $Al_2O_3$ inter-layer with a 80 nm thickness was grown between the FeCrAl alloy foam and the NiO catalysts, it indicated improved dispersion and stability of the NiO catalysts compared to the other samples. The performance improvement can be explained by optimum thickness of $Al_2O_3$ inter-layer resulting from the role of a passivation layer.

• Korean Journal of Materials Research
• /
• v.10 no.4
• /
• pp.295-300
• /
• 2000

Uniform silicon tip arrays were fabricated using the reactive ion etching followed by the reoxidation sharpening, and the effect of Pd-coated layer on electron emission characteristics was studied. The electron emission from Si field emitter arrays(FEAs) was a little, but improved by removing surface oxide on the FEA, but pronounced drastically by coating a $100-{\AA}-thick$ Pd metal layer. The turn-on voltage in the Pd-coated Si FEAs was reduced by 30 V in comparison with that in uncoated ones. This results from the increase of surface roughness at the tip apex by the Pd coating on Si FEA, via the decrease of the apex radius at which electrons are emitting. The Pd-coated emitters showed superior operating stability over a wide current range to that of the uncoated ones. This suggests that Pd coating enhances the high temperature stability and the surface inertness Si FEA.

• Korean Journal of Materials Research
• /
• v.14 no.2
• /
• pp.90-93
• /
• 2004

Silicon dioxide thin films were deposited on p-type Si (100) substrates by atomic layer deposition (ALD) method using alternating exposures of $SiH_2$$Cl_2$ and $O_3$ at $300^{\circ}C$. $O_3$ was generated by corona discharge inside the delivery line of $O_2$. The oxide film was deposited mainly from $O_3$ not from $O_2$, because the deposited film was not observed without corona discharge under the same process conditions. The growth rate of the deposited films increased linearly with increasing the exposures of $SiH_2$$Cl_2$ and $O_3$ simultaneously, and was saturated at approximately 0.35 nm/cycle with the reactant exposures over $3.6 ${\times}$ 10^{9}$ /L. At a fixed $SiH_2$$Cl_2$ exposure of $1.2 ${\times}$ 10^{9}$L, growth rate increased with $O_3$ exposure and was saturated at approximately 0.28 nm/cycle with $O_3$ exposures over$ 2.4 ${\times}$ 10^{9}$ L. The composition of the deposited film also varied with the exposure of $O_3$. The [O]/[Si] ratio gradually increased up to 2 with increasing the exposure of $O_3$. Finally, the characteristics of ALD films were compared with those of the silicon oxide films deposited by conventional chemical vapor deposition (CVD) methods. The silicon oxide film prepared by ALD at $300^{\circ}C$ showed better stoichiometry and wet etch rate than those of the silicon oxide films deposited by low-pressure CVD (LPCVD) and atmospheric-pressure CVD (APCVD) at the deposition temperatures ranging from 400 to $800^{\circ}C$.

• Korean Chemical Engineering Research
• /
• v.43 no.3
• /
• pp.401-406
• /
• 2005

In this work, the effect of chemical treatment of multiwalled carbon nanotubes (MWNTs) on glass transition temperature (Tg), thermal stability, and dynamic viscoelastic behaviors of MWNTs-reinforced epoxy matrix composites has been studied by differencial scanning calorimeter (DSC), thermogravimetric analysis (TGA), and dynamic mechanical analysis (DMA) measurements. The MWNTs were chemically treated with 35 wt％ $H_3PO_4$ (A-MWNTs) or 35 wt％ KOH (B-MWNTs) solutions and the changes of surface properties of chemically treated MWNTs were examined by pH, acid and base values, Fourier transfer-infrared spectroscopy (FT-IR), and x-ray photoelectron spectroscopy (XPS) analyses. The chemical treatments based on acid and base reactions led to a significant change of surface characteristics and chemical compositions of the MWNTs, especially A-MWNTs/epoxy composites had higher thermal stability and dynamic viscoelastic properties than those of B-MWNTs and non-treated MWNTs/epoxy composites. These results were probably due to the improvement of interfacial bonding strength, resulting from the acid-base interaction and hydrogen bonding between the epoxy resins and the MWNT fillers.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.851-856
• /
• 2002

Tribological behavior of plasma-sprayed $Cr_2O_3$-based coatings containing $MoO_3$ at 450$^{\circ}C$ was investigated to understand the influence of $MoO_3$. A reciprocal disc-on-plate type tribo-tester was employed to examine fricition and wear behavior of the specimens. The microstructure and phase composition of the coating was characterized with Transmission Electron Microscopy(TEM). The TEM analysis indicated that $MoO_3$ was dispersed into the grain boundary, resulting in the increase of the hardness and density of the coating. Worn surfaces were investigated by scanning electron microscopy and chemistry of the worn surfaces was analyzed using a X-ray Photoelectron Spectrometer(XPS). The results showed that the friction coefficient of the $MoO_3$-added coatings was lower than that without $MoO_3$ addition. The larger protecting layers were observed at the worn surface of plasma spray coated specimens with $MoO_3$ composition in the protecting layer appears to be more favorable in reducing the friction.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.4
• /
• pp.11-16
• /
• 2002

In this study, the dry etching characteristics of $SrBi_2Ta_2O_9$ (SBT) thin films were investigated by using ICP-RIE (inductively coupled plasma-reactive ion etching). The etching damage and degradation were analyzed with XPS (X-ray photoelectron spectroscopy) and C-V (Capacitance-Voltage) measurement. The etching rate increased with increasing the ICP power and the capacitively coupled plasma (CCP) power. The etch rate of 900$\AA$/min was obtained with 700 W of ICP power and 200 W of CCP power. The main problem of dry etching is the degradation of the ferroelectric material. The damage-free etching characteristics were obtained with the $Ar/C1_2/CHF_3$ gas mixture of 20/14/2 when the ICP power and CCP power were biased at 700 W and 200 W, respectively. The experimental results show that the dry etching process with ICP-RIE is applicable to the fabrication of the single transistor type ferroelectric memory device.

• Journal of Sensor Science and Technology
• /
• v.5 no.5
• /
• pp.79-84
• /
• 1996

A $1\;{\mu}m$ thick n-type GaAs layer with Si doping density of $1{\times}10^{17}/cm^{3}$ and a $500{\AA}$ thick undoped single crystalline AlAs layer were subsequently grown by molecular beam epitaxy on the $n^{+}$ GaAs substrate. The AlAs/GaAs layer was oxidized in $N_{2}$ bubbled $H_{2}O$ vapor($95^{\circ}C$) ambient at $400^{\circ}C$ for 2 and 3 hours. From the result of XPS analysis, small amounts of $As_{2}O_{3}$, AlAs, and elemental As were found in the samples oxidized up to 2 hours. After 3 hours oxidation, however, various oxides related to As were dissolved and As atoms were diffused out toward the oxide surface. The as-grown AlAs/GaAs layer was selectively converted to $Al_{2}O_{3}/GaAs$ at the oxidation temperature $400^{\circ}C$ for 3 hours. The oxidation temperature and time is very critical to stop the oxidation at the AlAs/GaAs interface and to form a defect-free surface layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.116-116
• /
• 2007

21 세기에 접어들면서 인터넷을 통한 정보 통신의 발달과 개인 휴대용 이동 통신기기의 활발한 보급에 따라 휴대형 전자기기들의 소형화와 고성능화로 나아가고 있다. 이러한 전자기기에 사용될 IC의 내장 메모리 또한 집적화 및 고속화, 저 전력화가 이루어져야 한다. 이러한 전자기기들에 필수적인 압전 세라믹스 부품 중 압전 부저 및 기타 음향 부품등을 각종 전자기기와 무선 전화기에 채택함으로써 압전 부품에 대한 수요와 생산이 계속 증가할 것으로 전망된다. 이처럼 압전 세라믹스를 이용한 그 응용 범위는 대단히 방대하며, 현재 모든 압전 부품들은 PZT 계열 재료로 만들어지고 있고, 차후 모두 비납계열 재료로 대체될 것이 확실시된다. Pb의 환경오염은 이미 오래전부터 큰 문제점으로 인식되고 있었으며 그 일례로 미국의 캘리포니아 주에서는 1986년부터 약 800종의 유해물질, 그 중에서도 Pb 사용을 300ppm 이하로 규제하는 Proposition 65를 제정하여 실행하고 있다. 그리고 2003년 2월에 EU (European Union) 에서 발표한 전자산업에 관한 규제 사항중 하나인 위험물질 사용에 관한 지칭 (Restriction of Hazardous Substance, RoHS) 에 의하면, 2006 년 7월부터 전기 전자 제품에 있어서 위험 물질인 Pb을 포함한 중금속 물질(카드늄, 수은, 6가 크롬, 브롬계 난연재)의 사용을 금지한다고 발표하였다. 비록 전자세라믹 부품에 함유된 Pb는 예외 사항으로 두었지만 대체 가능한 물질이 개발되면 전자세라믹 부품에서도 Pb의 사용을 금지한다고 규정하였다. 더욱이 일본은 2005 년부터 Pb 사용을 금지시켰다. 이와 같이 Pb가 환경에 미치는 영향 때문에 비납계 강유전 물질 및 압전 세라믹스 재료에 대한 연구가 전 세계적으로 활발히 진행되고 있다. 본 연구에서는 비납계 강유전체의 patterning을 위해서, NKN 박막을 고밀도 플라즈마원인 ICP를 이용하여 식각 mechanism을 연구하고, 식각변수에 따른 식각 공정을 최적화에 대하여 연구하였다. 가스 혼합비에 따라 식각 할때 700 W의 RF 전력과 - 150 V의 직류 바이어스 전압을 인가하였고, 공정 압력은 2 Pa, 기판 온도는 $23^{\circ}C$로 고정하였다. 식각 속도는 Tencor사의 Alpha-step 500을 이용하여 측정되었으며 식각 시 NKN 박막 표면과 라디칼과의 화학적인 반응을 분석하고 식각 메커니즘을 규명하기 위하여 XPS(x-ray photoelectron spectroscopy)를 사용하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.113-113
• /
• 2000

직접천이형 wide band gap(3.4eV) 반도체중의 하나인 GaN를 청색 및 자외선 laser diode, 고출력 전자장비 등으로 응용하기 위해서는 낮은 접합저항을 갖는 Ohmic contact이 선행되어야 한다. 그러나 만족할만한 p-type GaN의 Ohmic contact은 아직 실현되고 있지 못하며, 이는 GaN와 접합 금속과의 구체적인 반응의 연구를 필요로 한다. 본 연구에서 앞서 Pt, Pt, Ni등의 late transition metal을 p-GaN에 접합시킨 결과 이들은 접합 당시 비교적 평탄하나 후열 처리과정에서 비교적 낮은 온도에서 기판과 열팽창계수의 차이로 인하여 평탄성을 잃어버리면서 barrier height가 증가한다는 사실을 확인하였다. 따라서 본 연구에서는 이러한 열적 불안정성을 극복하기 위하여 Ni과 Pd를 차례로 증착하고 가열하면서 interfacial reaction, film morphology, Fermi level의 움직임을 monchromatic XPS(x-ray photoelectron spectroscopy) 와 SAM(scanning Auger microscopy) 그리고 ex-situ AFM을 이용하여 밝히고자 하였다. 특히 후열처리에 의한 계면 반응에 수반되는 구성 금속원소 간의 합금현상과 금속 층의 평탄성이 밀접한 관계가 있다는 것을 확인하였다. 이러한 합금과정에서 나타나는 금속원소들의 중심 준위의 이동을 체계적으로 규명하기 위해서 Pd1-xNix와 Pd1-xGax 합금들의 표준시료를 arc melting method로 만들어 농도에 따른 금속원소들의 중심 준위의 이동을 측정하여, Pd/Ni/p-GaN 및 Ni/Pd/p-GaN 계에서 열처리 온도에 따른 interfacial reaction을 확인하였다. 그 결과 두 계가 상온에서 nitride 및 alloy를 형성하지 않고 고르게 증착되고, 열처리 온도를 40$0^{\circ}C$에서 $650^{\circ}C$까지 증가시킴에 따라 계면반응의 부산물인 metallic Ga은 증가하고 있으마 nitride는 여전히 형성되지 않는 것을 확인하였다. 증착당시 Ni이 계면에 있는 Pd/Ni/p-GaN의 경우에는 52$0^{\circ}C$까지의 열처리에 의하여 Ni과 Pd가 골고루 섞이고 그 평탄성도 유지되고 barier height의 변화도 없었다. 더 높은 $650^{\circ}C$ 가열에 의해서는 surface free energy가 작은 Ga의 활발한 편석 현상으로 인해 표면은 Ga이 풍부한 Pd-Ga의 합금층으로 덮이고, 동시에 작은 pinhole들이 발생하며 barrier height도 0.3eV 가량 증가하게 된다. 반면에 증착당시 Pd이 계면에 있는 Ni/Pd/p-GaN의 경우에는 40$0^{\circ}C$의 가열까지는 두 금속이 그들 계면에서부터 섞이나, 52$0^{\circ}C$의 가열에 의해 이미 barrier height가 0.2eV 가량 증가하기 시작하였다. 더 높은 $650^{\circ}C$가열에 의해서는 커다란 pinhole, 0.5eV 가량의 barrier height 증가, Pd clustering이 동시에 관찰되었다. 따라서 Ni과 Pd의 일함수는 물론 thermal expansion coefficient가 거의 같으며 surface free energy도 거의 일치한다는 점을 감안하면, 이렇게 뚜렷한 열적 안정성의 차이는 GaN와 contact metal과의 반응시작 온도(disruption onset temperature)의 차이에 기인함을 알 수 있었다. 즉 계면에서의 반응에 의해 편석되는 Ga에 의해 박막의 strain이 이완되면, pinhole 등의 박막결함이 줄어 들고, 이는 계면의 N의 out-diffusion을 방지하여 p-type GaN의 barrier height 증가를 막게 된다.