• Journal of Biomedical Engineering Research
• /
• v.41 no.5
• /
• pp.179-184
• /
• 2020

Purpose: The purpose of this study was to evaluate the effect according to the NEX, VENC, targeted cardiac phases on the velocity measurement of 4D phase-contrast MRI. Materials and Methods: The abdominal aortic phantom was made to experiment. The working fluid was mixed with water and glycerin to mimic the density and viscosity of human blood. The inlet velocity was Reynolds number 2000. The experimental conditions were NEX 1 and 4, VENC 102 cm/s and 200 cm/s, and 10 and 15 targeted cardiac phases, respectively. The average flow rate, average velocity, maximum velocity, and cross-section area were measured. Results: As a result of the case-by-case comparison, the error rate was less than 5%. There was no significant difference (p > 0.05). Conclusion: It is expected that this result will be useful for acquiring blood flow information in clinical practice.

• Journal of the Korean Society for Heat Treatment
• /
• v.1 no.1
• /
• pp.8-12
• /
• 1988

This study has been carried out to evaluate gaseous nitrocarburizing treatment undertaken for pure iron at $570^{\circ}C$ in an atmosphere containing 50% endothermic gas, generated from natural gas, and 50% ammonia. The results obtained from the experiment are as follows ; 1) The microstructure of gaseous nitrocarburized pure iron consists of the compound layer on the surface and the diffusion zone beneath it. The compound layer progresses uniformly into ferrite with a thickness of $20{\mu}$ obtained after treating for 3 hours. 2) Chemical analysis has shown that the compound layer has a C/N ratio of 0.19 and that the average combined interstitial content of the compound layer is about 30 atomic percent, which is close to the lower limit of the ${\varepsilon}$-carbonitride phase field in Fe-C-N phase diagram. 3) X-ray diffraction analysis has revealed that the compound layer consists mainly of the c.p.h. phase, ${\varepsilon}-Fe_3$(C.N) and a small amount of $Fe_4N$ and traces of ferrite are also present in the compound layer. 4) The microhardness of the compound layer is about 600 V.H.N and shows a relatively sharp fall-off at the compound layer/diffusion zome interface. 5) The average actual degree of ammonia dissociation is calculated to be 27% for a gaseous nitrocarburizing treatment carried out at $570^{\circ}C$.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.172-179
• /
• 2004

Average Bi-directional flow tube was suggested to measure single and two phase flow rate. Its working principle is similar with Pilot tube, however, it makes it possible to eliminate the cooling system which is normally needed to prevent from flashing in the pressure impulse line of Pilot tube when it is used in the depressurization condition. The suggested instrumentation was tested in the air-water vertical test section which has 80mm inner diameter and 10m length. The flow tube was installed at 120 of L/D from inlet of test section. From the test, single air and water flow rate was measured successfully. For the emasurement of two phase flow rate, Chexal drift-flux correlation was used. In the test a new correlation of momentum exchange factor was suggested. The test result shows that the suggested instrumentation using the measured void fraction and Chexal drift-flux correlation can predict the mass flow rates within $10\%$ error of measured data.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.1
• /
• pp.27-33
• /
• 2001

This paper presents a digital instrument for a DSP based power quality analysis in three phase power system where current waveform is non-sinusoidal. it is based on stand alone type TMS320C31 DSP(digital signal processor)board and on a special high-speed data acquisition system. Power quality of low power motor drives are analyzed and processed by using a simple average power algorithm, and result of power analysis are displayed by LCD in the proposed system. This paper also goes on to discuss the performance of an instrument prototype, both in terms of accuracy and speed of measurement under the transient and steady state condition.

• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.589-594
• /
• 1999

The effect of $\beta$-heat treatment on th microstructure, mechanical properties and texture in the nuclear fuel cladding of Zircaloy-4 tubes was chosen at 1000, 1100 and 120$0^{\circ}C$, and the tubes were heat-treated by a high frequency vacuum induction furnace. Morphology of the second phase particles and $\alpha$-grain of as-received tubes were markedly changed by heat treatment. The average sizes of second phase particles of as-received and $\beta$-heat treated tubes were 0.1$\mu\textrm{m}$ and 0.076$\mu\textrm{m}$, respectively. However, the average sizes of second phase particles were not much changed in the $\beta$-heated temperatures. With increasing heat treatment temperatures, the 0.2% yield strength and the hoop strength were decreased because of changes in preferred orientation as will as $\alpha$-plate width. Heat treated Zircaloy-4 tubes exhibited texture changes but the preferred orientation of grains still remained.

• Journal of KIISE
• /
• v.42 no.9
• /
• pp.1071-1077
• /
• 2015

In this paper, we adopt PCM (phase-change memory) as a virtual memory swap device and present a new page replacement policy that considers the characteristics of PCM. Specifically, we aim to reduce the write traffic to PCM by considering the dirtiness of pages when making a replacement decision. The proposed policy tracks the dirtiness of a page at the granularity of a sub-page and replaces the least dirty page among the pages not recently used. Experimental results show that the proposed policy reduces the amount of data written to PCM by 22.9% on average and up to 73.7% compared to CLOCK. It also extends the lifespan of PCM by 49.0% and reduces the energy consumption of PCM by 3.0% on average.

• Journal of Korean Academy of Oral Health
• /
• v.42 no.4
• /
• pp.109-117
• /
• 2018

Objectives: The purpose of this study was to evaluate the customized oral health promotion program for North Korean defectors (NKDs). Methods: Using a pre-survey comprising phases 1-5 of the PRECEDE-PROCEED model, a customized oral health promotion program was created. The participants, a total of 129 NKDs, were allocated to the experimental group (n=64; 43 females and 21 males) or the control group (n=65; 46 females and 19 males). After the interventions, phases 7 to 9 of the PRECEDE-PROCEED model were executed to determine the effect of the program. Results: The results for phase 7 revealed high satisfaction with the program, with an average of 2.89 out of 3 points. In phase 8, concerning the impact evaluation, it was found that oral health beliefs and oral health knowledge were improved, with statistically significance differences before and after the experiment. Phase 9, concerning the outcome evaluation, showed that there were statistically significant differences in the average within groups before and after education in oral health beliefs (OHB), O'Leary index scores, and CPI. In terms of the difference between the groups, there were statistically significant improvement in OHB, O'Leary index scores, and CPI after the education program. Conclusions: The oral health promotion program developed in this study has made a positive contribution to improve the oral health status of NKDs.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.19 no.2
• /
• pp.11-25
• /
• 2023

With the increasing advancement of VLSI technology, health care system is also developing to serve the humanity with better care. Therefore, biomedical implantable devices are one of the amazing important invention of scientist to collect data from the body cell for the diagnosis of diseases without any pain. This Biomedical implantable transceiver circuit has several important issues. Oscillator is one of them. For the design flexibility and complete transistor-based architecture ring oscillator is favorite to the oscillator circuit designer. This paper represents the design and analysis of the a 9-stage CMOS ring oscillator using cadence virtuoso tool in 180nm technology. It is also designed to generate the carrier signal of 403.5MHz frequency. Ring oscillator comprises of odd number of stages with a feedback circuit forming a closed loop. This circuit was designed with 9-stages of delay inverter and simulated for various parameters such as delay, phase noise or jitter and power consumption. The average power consumption for this oscillator is 9.32㎼ and average phase noise is only -86 dBc/Hz with the source voltage of 0.8827V.

• The Journal of Korean Society for Radiation Therapy
• /
• v.26 no.1
• /
• pp.69-76
• /
• 2014

Purpose : To evaluate the changes of the motion of abdominal cavity between interfraction and intrafraction by using abdominal compression for reducing abdominal motion. Materials and Methods : 60 MVCT images were obtained before and after tomotherapy from 10 prostate cancer patients over the whole radiotherapy period. Shift values ( X -lateral Y -longitudinal Z -vertical and Roll ) were measured and from it, the correlation of between interfraction set up change and intrafraction target motion was analyzed when applying abdominal compression. Results : The motion changes of interfraction were X-average $0.65{\pm}2.32mm$, Y-average $1.41{\pm}4.83mm$, Z-average $0.73{\pm}0.52mm$ and Roll-average $0.96{\pm}0.21mm$. The motion changes of intrafraction were X-average $0.15{\pm}0.44mm$, Y-average $0.13{\pm}0.44mm$, Z-average $0.24{\pm}0.64mm$ and Roll-average $0.1{\pm}0.9mm$. The average PTV maximum dose difference was minimum for 10% phase and maximum for 70% phase. The average Spain cord maximum dose difference was minimum for 0% phase and maximum for 50% phase. The average difference of $V_{20}$, $V_{10}$, $V_5$ of Lung show bo certain trend. Conclusion : Abdominal compression can minimize the motion of internal organs and patients. So it is considered to be able to get more ideal dose volume without damage of normal structures from generating margin in small in producing PTV.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.275-279
• /
• 1998

The influence of $WO_3$ (0.5-4.0mol%) on the microstructural and electrical properties of ZnO varistors was investigated. The major part of a tungsten segregated to the nodal point. SEM, EDAX, and XRD analysis revealed that three phase, such as W-rich phase, Bi-rich phase, and spinel phase, coexist at the nodal point. The average grain size increased in the range of 15.5-29.9pm with increasing $WO_3$ content. This may be probably attributed to liquid phase formed by $WO_3$, $WO_3$ acted as promotion additive of grain growth. As $WO_3$ content increase, the varistor voltage greatly decreased in the range 186.82-35.87V/mm due to the increase of grain growth. The barrier height decreased in the range 1.93-0.42eV with increasing $WO_3$content.