• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_2
• /
• pp.1003-1008
• /
• 2022

This paper proposes a method related to fault tolerance operation and characteristic analysis of asymmetric 6-phase permanent magnet synchronous motor. In general, motor drive systems with multi-phase structures can be continuously operated despite a reduction of power and speed by using a phase changeover or control techniques according to the failures. As a result, it is widely used in industrial fields such as aviation and defense, which require high efficiency and high reliability. In this paper, the second order ripple of the electrical fundamental freuqnecy occurs in the dq-axis currents of the synchronous coordinate system through mathematical analysis according to the switch open of the dual 3-phase inverter. Therefore, the fault tolerant operation method is presented by applying the fault detection method with a constant cycle for continuous operations. The effectiveness of the proposed fault tolerance operation method is verified through the several experiments.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.1
• /
• pp.7-13
• /
• 2021

This paper proposes a method to minimize the target's direction detection error using RADAR. The radar system cannot accurately detect the target direction due to the phase error of he received signal. The proposed method of this study obtains a phase by applying an root mean square to each antenna incident signal, and reduces the phase error by using an optimal signal to noise ratio. In the simulation result, the probability of detecting the target direction is the best when the antenna spacing is half wavelength. The conventional method of direction detection probability 10-1.7 and the proposed method is 10-3.3. The target detection direction of the existing method represents [-8°,8°] with an error of 2 degrees. The target detection direction of the proposed method is shown in [-10°,10°], and all target directions are accurately detected. In the future, There is need for a method to reduce the phase error even though the resolution decrease.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1513-1525
• /
• 2016

Rapid and accurate phase synchronization is critical for the reliable control of grid-tied inverters. However, the commonly used software phase-locked loop methods do not always satisfy the need for high-speed and accurate phase synchronization under severe grid imbalance conditions. To address this problem, this study develops a novel open-loop phase locking scheme based on a synchronous reference frame. The proposed scheme is characterized by remarkable response speed, high accuracy, and easy implementation. It comprises three functional cascaded blocks: fast orthogonal signal generation block, fast fundamental-frequency positive sequence component construction block, and fast phase calculation block. The developed virtual orthogonal signal generation method in the first block, which is characterized by noise immunity and high accuracy, can effectively avoid approximation errors and noise amplification in a wide range of sampling frequencies. In the second block, which is the foundation for achieving fast phase synchronization within 3 ms, the fundamental-frequency positive sequence components of unsymmetrical grid voltages can be achieved with the developed orthogonal signal construction strategy and the symmetrical component method. The real-time grid phase can be consequently obtained in the third block, which is free from self-tuning closed-loop control and thus improves the dynamic performance of the proposed scheme. The proposed scheme is adaptive to severe unsymmetrical grid voltages with sudden changes in magnitude, phase, and/or frequency. Moreover, this scheme is able to eliminate phase errors induced by harmonics and random noise. The validity and utility of the proposed scheme are verified by the experimental results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.7
• /
• pp.1511-1517
• /
• 2014

Based on the simulation model for phase noise effect, the phase noise performance of communication system using the M-ary APSK modulation method is analyzed in this paper. The phase noise effects for APSK higher order modulation method are modeled by considering the signal constellations of the modulation methods. The simulation model is verified by comparing the analytic results for lower order modulation signals with simulated results for those modulation signals. Based on the simulation model, then, the phase noise effects for M-ary APSK are analyzed. The simulated results for PSK lower order modulation signals are in agreement with the results by the analytic model in the order of 1 %. The proper phase noise effects for M-ary APSK modulation signals are deduced by the simulation model. Also, the required signal-to-noise ratios of phase noise are proposed for phase noise degradations, which are used as the design parameter that considers the phase noise effect.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.1030-1036
• /
• 1994

The ceramics in the system 0.5[Pb(Ni1/3Nb2/3)O3]-0.5[0.65PbTiO3-0.35PbZrO3] were prepared by conventional solid state reaction method, double calcined method (columbite precursor method) and flux method using NaCl-KCl. Amount of pyrochlore phase for the calcined powders, sintering charateristrics, dielectric and piezoelectric properties were then investigated. Sintering temperature was 1000~120$0^{\circ}C$ and in case of flux method, the amount of flux to oxide was 1 : 1 mole ratio. The dielectric and piezoelectric properties of ceramics prepared by double calcined method and flux method were found to be better than those by conventional method. It was also possible to lower sintering temperature and reduce the amount of pyrochlore phase either by double calcined method or flux method. But with increasing sintering temperature, the difference in characteristrics due to diffrent fabrication method gradually.

• Journal of the Korea Convergence Society
• /
• v.8 no.1
• /
• pp.1-6
• /
• 2017

In this paper, we propose a new method for a correlative phase comparison direction finding(DF) which detects the arrival direction of radio waves by data fusing the calculated phase difference and the measured phase difference between the antennas when the radio waves are incident on the circular array antenna composed of 7 antennas respectively. The correlation type phase comparison method uses a uniform circular array(UCA) and a linear array method. The phase difference data calculated formally and the phase difference data measured in the test environment are fused with a correlation function, therefore, it is superior to the currently used phase comparison direction detection method. When the signal-to-noise ratio (SNR) of the received signal is 20dB and the inter-antenna distance to the wavelength of the received signal($L/{\lambda}$) is 0.5, the accuracy of the correlative DF is $1.7^{\circ}$ while measurement phase comparison's is larger than $2.5^{\circ}$, It can be used for electromagnetic signal monitoring and military direction detection.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.3
• /
• pp.125-131
• /
• 2007

Electric motor efficient improvement from home appliance field is important to the effect reducing the energy consumption. But the electric motor design/analysis technology is still insufficient. Specially the electric motor design/analysis technology of satisfying characteristic of both the induction motor and the synchronous motor such as Line start permanent motor. Therefore the electric motor design/analysis technology is urgently demanded reliability. This paper proposes the sing1e-phase line-start permanent magnet motor to develop the motor it with be able to alternate the sing-phase induction motor it is a refrigerator compressor motor. The sing-phase induction motor is analyzed in the steady state. And we have a certification test to compare our single-phase line-start permanent magnet motor with the sing-phase induction motor. In order to improve the performance, the stator of the single-phase line-start permanent magnet motor is same as the stator of the sing-phase induction motor and changes the rotor form and has the permanent magnet. It used the Finite Element Method(FEM) which is widely used with electronic-magnetic field numerical analysis method.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.2
• /
• pp.304-310
• /
• 2016

This paper proposes a fault diagnosis method for an open-fault in inverter driving five-phase induction motor. The five-phase induction motor has a high output torque and small torque ripple in comparison to three-phase. The best advantage of the five-phase induction motor is fault diagnosis and tolerant control using redundancy of phases. This paper uses an inverter as a power converter for driving a five-phase induction motor. If a switch of inverter occurs to the open-fault, this problem is the influence on the output current and output torque. To solve this problem, there is need of an accurate diagnosis and fault switch distinction. Therefore, this paper propose a fault detection method of the open-fault switches for the fault diagnosis. First, analyzing the pattern for the open-circuit fault of one phase. next, analyzing the pattern for the open-circuit fault of each inverter switches. Through the pattern analysis, It defines the scope of each of the failure switch. Thereafter, By using an algorithm that proposes to perform a fault diagnosis method. The proposed algorithm is verified from the experiment with the 1.5 kW five-phase induction motor.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.13 no.5
• /
• pp.24-29
• /
• 1976

In the phase locked AM signal detection, phase locked loop is used to extract a synchronous carrier from an input AM signal. Under the assumption that input noise is white Gaussian and free-running frequency of voltage controlled oscillator is the same that of an input carrier, operational behaviours of phase locked loop is analyzed and signal to noise ratio of the detection is derived quentitatively. The results show that the phase locked AM signal detection method offers a higher degree of noise mmunity than conventional AM signal detections.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.6
• /
• pp.38-46
• /
• 2012

In this paper, the necessity for the identification of the absolute phase value is introduced and analyzed for a particular conductor line of a 3-phase type distribution network and the recent methods are also introduced. For the determination of the exact phase value for a specific point in the line, as compared with the phase reference point, the measured phase value must be within a range of ${\pm}60[^{\circ}]$. However, the phase of a particular point can fluctuate depending on the line constant, transformer wiring method, line length, line amperage, etc. A theoretical formulation such as Simulink modeling and analysis for a distribution network are conducted for the identification of phase at a specific point in the line. In particular, through evaluating the effects of unbalanced current loads at the time of determination of the phase value, the limitations of the present method for the determination of phases is described.