• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.4
• /
• pp.212-215
• /
• 2018

The phase evolution, microstructure, and microwave dielectric properties of $Ba(Mg_{0.5-2x}Y_{2x}W_{0.5-x}Ti_x)O_3$ (x = 0.005~0.05) ceramics sintered at $1,700^{\circ}C$ for 1h were investigated. All compositions exhibited a 1:1 ordered cubic perovskite structure. The field emission scanning electron microscopy image revealed a dense microstructure in all the compositions. As the value of x increased, the lattice parameter, dielectric constant, and quality factor increased. The temperature coefficient of resonant frequency changed from $-19.6ppm/^{\circ}C$ to $-5.9ppm/^{\circ}C$ with increasing x value. The dielectric constant, quality factor, and temperature coefficient of resonant frequency of $Ba(Mg_{0.40}Y_{0.10}W_{0.45}Ti_{0.05})O_3$ were 21.7, 132,685 GHz, and $-5.9ppm/^{\circ}C$, respectively.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.1
• /
• pp.16-28
• /
• 2007

The results of experimental investigation of coherent structures beneath wind-generated waves in deep water are presented. Vorticity fields of deepwater wind waves were visualized by analyzing the velocity fields obtained by PIV measurements under different wind and fetch conditions. In addition, spatio-temporal evolution of the coherent structures and subsequent changes in vertical profiles of the instantaneous vorticity were qualitatively examined. It was found that a coherent structure is formed right underneath the wave crest and traveled in phase with the surface wave. The direction of rotation of the coherent structure was contrary to the wave orbital motion when wind speed is less than 10 m/s, while was same as the wave orbital motion when wind speed is approximately 13 m/s and wave breaking occurs at the wave crest. In the near-surface region, complex vortex-vortex interactions were observed according to the traveling of the coherent structure. In contrast, coherent structures far below the water surface changed little due to weak influence of orbital motion by the surface waves.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.383-383
• /
• 2010

Gas-phase hydrogen atoms create a variety of chemical and physical phenomena on Si surfaces: adsorption, abstraction of pre-adsorbed H, Si etching, Si amorphization, and penetration into the bulk lattice. Thermal desorption/evolution analyses exhibited three distinct peaks, including one from the crystalline bulk. It was previously found that thermal-energy gaseous H(g) atoms penetrate into the Si(100) crystalline bulk within a narrow substrate temperature window(centered at ~460K) and remain trapped in the bulk lattice before evolving out at a temperature as high as ~900K. Developing and sustaining atomic-scale surface roughness, by H-induced silicon etching, is a prerequisite for H absorption and determines the $T_s$ windows. Issues on the H(g) absorption to be further clarified are: (1) the role of the detailed atomic surface structure, together with other experimental conditions, (2) the particular physical lattice sites occupied by, and (3) the chemical nature of, absorbed H(g) atoms. This work has investigated and compared the thermal H(g) atom absorptivity of Si(100), Si(111) and Si(110) samples in detail by using the temperature programmed desorption mass spectrometry (TPD-MS). Due to the differences in the atomic structures of, and in the facility of creating atom-scale etch pits on, Si(100), (100) and (110) surfaces, the H-absorption efficiency was found to be larger in the order of Si(100) > Si(111) > Si(110) with a relative ratio of 1 : 0.22 : 0.045. This intriguing result was interpreted in terms of the atomic-scale surface roughening and kinetic competition among H(g) adsorption, H(a)-by-H(g) abstraction, $SiH_3(a)$-by-H(g) etching, and H(g) penetraion into the crystalline silicon bulk.

• Korean Journal of Materials Research
• /
• v.22 no.10
• /
• pp.562-568
• /
• 2012

Metal nanowires can be coated on various substrates to create transparent conducting films that can potentially replace the dominant transparent conductor, indium tin oxide, in displays, solar cells, organic light-emitting diodes, and electrochromic windows. One issue with these metal nanowire based transparent conductive films is that the resistance between the nanowires is still high because of their low aspect ratio. Here, we demonstrate high-performance transparent conductive films with silver nanofiber networks synthesized by a low-cost and scalable electrospinning process followed by two-step sequential thermal treatments. First, the PVP/$AgNO_3$ precursor nanofibers, which have an average diameter of 208 nm and are several thousands of micrometers in length, were synthesized by the electrospinning process. The thermal behavior and the phase and morphology evolution in the thermal treatment processes were systematically investigated to determine the thermal treatment atmosphere and temperature. PVP/$AgNO_3$ nanofibers were transformed stepwise into PVP/Ag and Ag nanofibers by two-step sequential thermal treatments (i.e., $150^{\circ}C$ in $H_2$ for 0.5 h and $300^{\circ}C$ in Ar for 3 h); however, the fibrous shape was perfectly maintained. The silver nanofibers have ultrahigh aspect ratios of up to 10000 and a small average diameter of 142 nm; they also have fused crossing points with ultra-low junction resistances, which result in high transmittance at low sheet resistance.

• Korean Journal of Materials Research
• /
• v.19 no.6
• /
• pp.293-299
• /
• 2009

The microstructures and mechanical properties of Dual Phase (DP), Transformation-Induced Plasticity (TRIP), and Quenching & Partitioning (Q&P) steels were investigated in order to define the strengthening mechanism of 0.2 C steel. An intercritical annealing between Ac1 and Ac3 was conducted to produce DP and TRIP steel, followed by quenching the DP and TRIP steel being quenched at to room temperature and by the TRIP steel being austemperingaustempered-air cooling cooled the steel toat room temperature, respectively. The Q&P steel was produced from full austenization, followed by quenching to the temperature between $M_s$ and $M_f$, and then enriching the carbon to stabilize the austenite throughout the heat treatment. For the DP and TRIP steels, as the intercritical annealing temperature increased, the tensile strength increased and the elongation decreased. The strength variation was due to the amount of hard phases, i.e., martensite and bainite, respectively in the DP and TRIP steels. It was also found that the elongation also decreased with the amount of soft ferrite in the DP and TRIP steels and with the amount of the that was retained in the austenite phasein the TRIP steel, respectively for the DP and TRIP steels. For the Q&P steel, as the partitioning time increased, the elongation and the tensile strength increased slightly. This was due to the stabilized austenite that was enriched with carbon, even when the amount of retained austenite decreased as the partitioning time increased from 30 seconds to 100 seconds.

• Korean Journal of Materials Research
• /
• v.18 no.1
• /
• pp.45-50
• /
• 2008

Microstructural evolution and the intermetallic compound (IMC) growth kinetics in an Au stud bump were studied via isothermal aging at 120, 150, and $180^{\circ}C$ for 300hrs. The $AlAu_4$ phase was observed in an Al pad/Au stud interface, and its thickness was kept constant during the aging treatment. AuSn, $AuSn_2,\;and\;AuSn_4$ phases formed at interface between the Au stud and Sn. $AuSn_2,\;AuSn_2/AuSn_4$, and AuSn phases dominantly grew as the aging time increased at $120^{\circ}C,\;150^{\circ}C,\;and\;180^{\circ}C$, respectively, while $(Au,Cu)_6Sn_5/Cu_3Sn$ phases formed at Sn/Cu interface with a negligible growth rate. Kirkendall voids formed at $AlAu_4/Au$, Au/Au-Sn IMC, and $Cu_3Sn/Cu$ interfaces and propagated continuously as the time increased. The apparent activation energy for the overall growth of the Au-Sn IMC was estimated to be 1.04 eV.

• The KIPS Transactions:PartD
• /
• v.16D no.4
• /
• pp.549-560
• /
• 2009

The Agile movement is a phenomenon that is part of the next phase of the software engineering evolution. At the same time, globally distributed software development is another trend delivering high-quality software to global users at lower costs. In this paper, Agile Framework for Distributed Software Development (AFDSD) has been suggested, and Chameleon project of Yahoo! Inc. has been implemented based on the framework. Also, the project has been evaluated by measuring Agile adoption and improvement levels, degrees of agility and agile project success, and comparing the performance and quality with the previous version. The overall performance and satisfaction with Chameleon increased by more than 30% since Agile techniques were adopted. Our objective is to highlight successful practices and suggest a framework to support adoption and evaluation of Agile techniques in a distributed environment.

• Metals and materials international
• /
• v.24 no.6
• /
• pp.1346-1358
• /
• 2018

A novel additive manufacturing method with TIG-MIG hybrid heat source was applied for fabricating 5356 aluminum alloy component. In this paper the microstructure evolution, mechanical properties and fracture morphologies of both as-deposited and heat-treated component were investigated, and how these were affected by different heat-treated temperature. The as-deposited microstructure showed dominant equiaxed grains with second phase, and the size of them is coarse in the bottom region, medium in the middle region and fine in the top region owing to different thermal cycling conditions. Compared with as-deposited microstructure, the size of grain becomes large and second phases gradually dissolve in the matrix as heat-treated temperature increase. Different microstructures determine the mechanical properties of component. Results show that average ultimate tensile strength enhances from 226 to 270 MPa and average microhardness increases from 64.2 to 75.3 HV0.1 but ductility decreases from 33 to 6.5% with heat-treated temperature increasing. For all components, the tensile properties are almost the same in the vertical direction (Z) and horizontal direction (Y) due to equiaxed grains, which exhibits isotropy, and the mechanisms of these are analyzed in detailed. In general, the results demonstrate that hybrid arc heat source has the potential to fabricate aluminum alloy component.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.68-70
• /
• 2014

Korean e-goverment has shown its development phase upgrade following the world' e-government evolution. By United Nations, Korea was ranked number one in e-government yet it was not even in top ten for past years. Even now, a number of Korean government organizations such as Ministry of Security and Public Administration and Ministry of Science, ICT and Future Planning have presented and executed various directions and strategies (for example, e-gov 3.0). On the other hand, World Economic Forum put Korea out of top 10 in Networked Readiness Index and hence wireless mobile communication of Korea is a weak point making difficulties for smart office and Bring Your Own Device (BYOD) implementation. This paper details the analysis of leading countries' strategies and policies on m-Government and provides some suggestions for Korean m-government.

• Korean Journal of Metals and Materials
• /
• v.47 no.10
• /
• pp.605-612
• /
• 2009

The suitability of twin roll strip casting for Ag-27.5%Cu-20.5%Zn-2.5%Mn-0.5%Ni brazing alloy (known as HS-49D) was examined in the present work and the mechanical properties and microstructure of the strip were also investigated. The effect of annealing heat treatment on the properties was also studied. The new manufacturing process has applications in the production of the brazing alloy. XRD and microstructural analyses of the Ag-27.5%Cu-20.5%Zn-2.5%Mn-0.5%Ni strip revealed a eutectic microstructure of an Ag-rich matrix (FCC) and a Cu-rich phase (FCC) regardless of heat treatment. The results of mechanical tests showed tensile strength of 434 MPa and 80% elongation for the twin roll casted strip. Tensile results showed decreasing strengths and increasing elongation with annealing heat treatment. Microstructural evolution and fractography were also investigated and related to the mechanical properties.