• 한국해양공학회지
• /
• 제23권3호
• /
• pp.40-45
• /
• 2009

With the increase in the annealing temperature, the volume fraction of austenite phase increased and the volume fraction of ferrite phase decreased. In compliance with the addition of N, not only the volume fraction of austenite phase was increased but also the austenite structure was made larger. Volume fraction of ${\sigma}$ phase was increased by decreasing of the volume fraction of ferrite phase, with the increase in the aging time and in compliance with the addition of N. As increasing in volume fraction of ${\sigma}$ phase, tensile strength and hardness increased, while elongation and impact value decreased. Elongation slowly decreased and impact value rapidly decreased at the early stage of aging. By the added N, tensile strength, elongation, hardness and impact value was increased.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.94-97
• /
• 1998

The conceptual design of integrated three phase superconducting fault current limiter (SFCL) is presented. And through simulation of power system where this SFCL is installed, the characteristics of this SFCL is analyzed. It is like three-phase transformer. So it has the same characteristics with inductive single phase SFCL. But it has more merits than single phase SFCL. Differently to single phase SFCL, integrated three phase SFCL induces impedance at all phase by any single phase fault to protect the power system more safely.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.227-230
• /
• 2001

A new control method of three phase converter without measuring input Phase-voltage and DC-link voltage is Proposed. Input Phase-voltage of these required voltages is estimated using EKF(Extended Kalman Filter) and DC-link voltage is estimated from the measured line currents and the estimated input phase-voltage. This control method is achieved without PLL(Phase Locked Loop) which senses the angle of input phase-voltage and DC-link voltage sensor. In additon, the proposed method controls high power factor and DC-link voltage utilizing the estimated phase angle. This paper describes the effectiveness of the proposed estimated algorithm through simulations.

• Advances in nano research
• /
• 제1권2호
• /
• pp.93-103
• /
• 2013

An ultrasonic-mediated assisted stepwise method has been developed for depositing transparent ZnO films from aqueous solution. Rinsing in low ethylene glycol temperature was easy to produce intermediate phase of $Zn(OH)_2$, rinsing in $120^{\circ}C$ ethylene glycol was observed the diffraction peak of intermediate $Zn(OH)_2$ in early report, the rinsing temperature plays an important role in the process of $Zn(OH)_2$ phase transformed to ZnO, high rinsing temperature actually improved the intermediate phase. However, the effect of rinsing on the intermediate phase is yet to be understood clearly. The effect of different rinsing procedures, involving either of or a combination of successive ionic layer adsorption and reaction (SILAR) and ultrasonic-assisted rinsing, prior to hydrolysis in ethylene glycol was found to improve the occurrence $Zn(OH)_2$ in ZnO thin films. In the zinc complex ($[Zn(NH_3)_4]^{2+}$) solution, excess ($[Zn(NH_3)_4]^{2+}$) absorbed in glass substrate transformed incompletely to ZnO and exist as $Zn(OH)_2$ phase in thin films. In films deposited at low temperature, rinsing procedure is applied to improve excess $Zn(OH)_2$ and obtain smoother transparent thin films.

• 한국재료학회지
• /
• 제24권11호
• /
• pp.610-616
• /
• 2014

In this study, we investigated the precipitation behavior of the R-phase precipitated at the initial stage of aging and its effect on the pitting corrosion of 25%Cr-7%Ni-4%Mo super duplex stainless steel. The R-phase in super duplex stainless steel was mainly precipitated at the interface of ferrite/austenite phases and inside of the ferrite phase during the initial stage of aging, and it was transformed into the ${\sigma}$-phase with an increase in aging time. The ferrite phase was decomposed into a new austenite phase and ${\sigma}$-phase. The R phase was an intermetallic compound, which represented a lower Ni and higher Mo than the matrix, and also had a higher Mo and Cr concentration than the ${\sigma}$ phase. With an increasing aging time, the pitting potential $E_p$ was increased slowly by the precipitation of the R-phase, and it was then steeply decreased by the precipitation of the ${\sigma}$-phase. The R-phase was decreased the pitting potential, but its effect was smaller than effect of ${\sigma}$-phase.

• Journal of Electrical Engineering and Technology
• /
• 제8권5호
• /
• pp.1107-1115
• /
• 2013

A new PWM technique for a two-phase BLDC motor fed by a two-phase eight-switch inverter is proposed in this paper. It is well known that a two-phase eight-switch inverter can significantly improve power output compared with a two-phase six-switch inverter in a two-phase motor drive. To drive the two-phase BLDC motor simply and effectively, two normal PWM strategies are investigated to manage speed regulation. However, under the conditions of low speed and light load, especially during the braking process, the current in a short time of one period is near zero, which is a discontinuous waveform every half period. To solve it, a novel PWM technique is investigated to improve the operational performance of normal technique. Using the new PWM scheme, the current continues every half period and the braking performance is improved. The effectiveness of the proposed PWM method is verified through the experiments.

• ETRI Journal
• /
• 제24권2호
• /
• pp.161-171
• /
• 2002

This paper proposes a novel decision feedback differential phase detection (DF-DPD) for M-ary DPSK. A conventional differential phase detection method for M-ary Differential Phase Shift Keying (DPSK) can simplify the receiver architecture. However, it possesses a poorer bit error rate (BER) performance than coherent detection because of the prior noisy phase sample. Multiple-symbol differential detection methods, such as maximum likelihood differential phase detection, Viterbi-DPD, and DF-DPD using L-1 previous detected symbols, have attempted to improve BER performance. As the detection length, L, increases, the BER performance of the DF-DPD improves but the complexity of the architecture increases dramatically. This paper proposes a simplified DF-DPD architecture replacing the conventional delay and additional architecture with an accumulator. The proposed architecture also improves BER performance by minimizing the current differential phase noise through the accumulation of previous differential phase noise samples. The simulation results show that the BER performance of the proposed architecture approaches that of a coherent detection with differential decoding.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.254-254
• /
• 2010

Cu-Pc(copper(II)-phthalocyanine)는 박막의 형성과정에서 열처리 방식과 온도에 따라 박막의 구조가 변하며, 구조로는 열적으로 준 안정적인 $\alpha$-phase와 열적으로 안정적인 $\beta$-phase가 있다. 본 연구에서는 Cu-Pc 박막의 열적으로 안정적인 $\beta$-phase 구조에 대해 온도 조건 변화에 따른 표면 결정 성장의 특성을 연구하고자 한다. 진공증착 방법 중 하나인 thermal evaporation deposition을 이용하여 glass 기판위에 전열 처리 및 후열 처리에 대해 온도 조건 변화에 따른 $\beta$-phase type의 표면 결정 특성을 연구하였다. Cu-Pc 박막의 성장두께는 50nm 일정한 두께로 fluxmeter 및 thickness monitor를 이용하여 제어하였다. 50nm의 두께에 따른 기판온도를 $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$로 전열 처리한 후 각각 전열 처리한 기판온도에 대해 1hour, 2hour, 3hour 후열 처리하여 온도 조건에 따른 박막을 성장한 후, $\beta$-phase type에 대한 결정 구조 및 표면 특성 변화를 분석하였다. 제작된 Cu-Pc의 박막은 $\beta$-phase type으로, 열처리에 따른 $\beta$-phase transition 현상을 연구하였다. XRD(X-ray diffraction)를 통하여 박막에 대한 결정 구조 분석 및 FE-SEM(field emission scanning electron microscopy)을 이용하여 Cu-Pc 박막의 구조적 결정성과 방향성 등, 표면 상태와 형상구조에 대해 표면의 특성을 분석하며, 광 흡수도(UV-visible absorption spectra)을 이용하여 온도 조건에 따른 투과/흡수 현상을 비교분석하였다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.49.1-49.1
• /
• 2011

태양전지 모듈의 25년 이상 보증을 위해 태양전지 모듈을 구성하는 부품 소재의 신뢰성이 부각되고 있다. 현재까지 알려진 태양전지 모듈용 에틸렌 아세테이트 비닐(ethylene Vinyl Acetate, EVA)의 주요 열화 메카니즘은 황변(yellowing)과 박리(delaminaation)이다. 따라서 본 연구에서는 태양전지 모듈을 구성하는 재료 중 EVA 소재의 열화 메커니즘을 도출하기 위해 이미 알려진 스트레스 인자를 이용한 가속 열화시험을 설계한 후 가속열화시험을 실시하였으며, 이로부터 EVA의 열화 메카니즘을 규명하였다. 열화모드 재현을 위해 소형 태양광 모듈을 제작하였으며, Weather-Ometer를 이용하여 열화시험을 수행하였다. 시험조건은 4종 Phase가 1 사이클이 되도록 실험하였으며, Dark 조건 1 Phase 및 Light 조건 3 Phase 조건으로 실시하였다. 태양전지 모듈의 열화량은 매 500 사이클 마다 Light I-V 변화량을 측정하여 분석하였다. EVA의 물리 화학적 열화분석을 위해 단면분석, 적외선분광기(Fourier Transform-Infra Red, FT-IR) 및 주사전자현미경을 이용하여 열화 특성에 대한 분석을 실시하였고, 이를 근거로 EVA의 열화 메커니즘을 규명하였다.

• 대한금속재료학회지
• /
• 제50권3호
• /
• pp.248-255
• /
• 2012

AlN thin films containing various amounts of Co, AlN-Co, and Al-Co alloy particles were prepared using a two-facing-target type dc reactive sputtering (TFTS) system. The as-deposited films exhibited the variable nature expected from an AlN-rich phase, and an amorphous-like phase, depending on the Co content in the films. Specific favorable microstructures were prepared by optimizing annealing conditions. Those microstructures and their magnetic properties and resistivity were investigated. As-deposited films showed very small saturation magnetization and an amorphous-like structure. However, when annealed, the as-deposited amorphous-like phase decomposes into phases of AlN, Co and Al-Co. These annealing induced changes in the microstructure improve the magnetization and resistivity of the films. Further improvement of soft magnetic properties could lead to the material being used for high density magnetic recording head material.