• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1668-1670
• /
• 2002

Since more than two decades, the conventional PD detecting systems have been employed in order to detect the partial discharges occurring inside the HV power apparatus for their diagnosis by use of different type of detection such as acoustic and UHF detection method. Regardless of their wide on-site application, a certain number of technical inconveniences have been disclosed as follows : multistage amplification. large volume, susceptible to external noise and high price. In this respect, the optical measurement techniques are widely proposed in these days in this concerned field ascribed to the following advantages : immune to external EMI noise and broad band response of the Pockels cell covering from DC to GHz. However, the reliability of several proposed techniques enabling to measure the electric field inside the large high power apparatus has not yet been well approved In this work, an optical measuring system, based on the Pockels effect, has been developed for measuring the field variation due to the corona discharges occurring in air and in oil. This system consists of He-Ne laser, single mode optical fiber, multi mode optical fiber, polarizing film, Y-cut LiNbO3 cell, photo detector, digital oscilloscope and personal computer with GPIB. For this purpose, optical probe has been specially designed and realized and put into the needle-plane electrode. Afterward, same measurement is carried out in oil. We demonstrate the characteristic of the optical measuring system and the measurement results.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.112-119
• /
• 1993

A strength and durability estimation system of involute cylindrical gears which are commonly used as power transmission devices is developed on the personal computer, which analyzed and/or evaluates the gear design and the service performance at the point of view of strength and durability. The typical considerations are the bending strength and the sunface durability, and the strength and durability estimations are carried out using the reliable standards of AGMA&ISO. In addition, the finite element analysis (FEM) of tooth bending stress is conducted in order to compare the real maximum stress with the estimaed bending stress by the standard. Therefore, the system is built so that the variables or factors considered differently in those standards and the strength & durability are appraised seperately by each method, and a series of the estimation processes is integrated into the system can be used in the initial design at the view point of strength and durability. And it is useful to the purpose of the trouble-shooting of gear system and the purpose of introducing the methods for maintaining design strength in service, with appraising the strength and durability after design or with appraising the influencing factors, as a whole. Therefore, this strength and durability estimation system can help the aim of automatic design of cylindrical gears.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.5
• /
• pp.805-815
• /
• 2001

Glaucoma is an eye disease which is caused by abnormal high IOP (Intra Ocular Pressure). High IOP is caused by the aqueous humor which is produced consistently but not drained due to malfunction of the trabecular system which has a role of draining the aqueous humor into the venous system. Currently, there are three methods to treat glaucoma-using medicines, surgical operation, and using implant device. The first and second methods are not long acting, so the use of implants is increasing in these days in order to drain out the aqueous humor compulsory. However, though conventional implants have a capability of pressure regulation, they cannot maintain IOPs desired for different patients, and too much aqueous humor are usually drained, to cause hypotony. To solve these problems, it is needed to develop a new implant which is capable of controling the IOP actively and copes with personal difference of patients. An active glaucoma implant consists of the valve actuator, pressure sensor, controller, and power supply. In this paper, firstly, we make an analysis of the operation of a conventional implant using a bond graph and show defects and limitations of the conventional valve analytically. Secondly, we design and analyze a valve actuator considering actuation principles, resistance elements, control methods, and energy sources focused on power saving problem. Finally, using simulations the possibility of the proposed valve actuator is investigated.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.2
• /
• pp.1070-1088
• /
• 2017

Recently, the applications of Internet of Things (IoTs) are growing rapidly. Wireless Sensor Network (WSN) becomes an emerging technology to provide the low power wireless connectivity for IoTs. The IPv6 over low-power wireless personal area networks (6LoWPAN) has been proposed by IETF, which gives each WSN device an IPv6 address to connect with the Internet. The transmission congestion in IoTs could be a problem when a large numbers of sensors are deployed in the field. Therefore, it is important to consider whether the WSN devices have be completely integrated into the Internet with proper quality of service (QoS) requirements. The Software Defined Network (SDN) is a new architecture of network decoupling the data and control planes, and using the logical centralized control to manage the forwarding issues in large-scale networks. In this research, the SDN-based 6LoWPAN Border Router (6LBR) is proposed to integrate the transmission from WSNs to Internet. The proposed SDN-based 6LBR communicating between WSNs and the Internet will bring forward the requirements of end-to-end QoS with bandwidth guarantee. Based on our experimental results, we have observed that the selected 6LoWPAN traffic flows achieve lower packet loss rate in the Internet. Therefore, the 6LoWPAN traffic flows classified by SDN-based 6LBR can be reserved for the required bandwidth in the Internet to meet the QoS requirements.

• Journal of Broadcast Engineering
• /
• v.13 no.5
• /
• pp.612-621
• /
• 2008

Due to the various constraints such as feasible size of data payload and low transmission power, no technical specifications on the voice communication are included in the Zigbee standard. In this paper, a voice coding technique for application to the IEEE 802.15.4 standard, which is the basis of Zigbee communication, is presented. Here, both high compression and good waveform recovery are essential. To meet those requirements, a multi-stage discrete wavelet transform (DWT) block and a binary coding block consisting of two different pulse-code modulations are exploited. Theoretical analysis and simulation results in an indoor wireless channel show that the voice coder with 2-stage DWT is most appropriate from the viewpoint of compression and waveform recovery. When the line-of-sight component is dominant, the voice coding scheme has good recovery capability even in the moderate signal-to-noise power ratios. Hence, it is considered that the presented scheme will be a technical reference for the future recommendation of voice communication exploiting Zigbee.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.2
• /
• pp.95-103
• /
• 2011

This paper proposes a 6b 1.2 GS/s 47.8 mW 0.17 $mm^2$ 65 nm CMOS ADC for high-rate wireless personal area network systems. The proposed ADC employs a source follower-free flash architecture with a wide input range of 1.0 $V_{p-p}$ at a 1.2 V supply voltage to minimize power consumption and high comparator offset effects in a nanometer CMOS technology. The track-and-hold circuits without source followers, the differential difference amplifiers with active loads in pre-amps, and the output averaging layout scheme properly handle a wide-range input signal with low distortion. The interpolation scheme halves the required number of pre-amps while three-stage cascaded latches implement a skew-free GS/s operation. The two-step bubble correction logic removes a maximum of three consecutive bubble code errors. The prototype ADC in a 65 nm CMOS demonstrates a measured DNL and INL within 0.77 LSB and 0.98 LSB, respectively. The ADC shows a maximum SNDR of 33.2 dB and a maximum SFDR of 44.7 dB at 1.2 GS/s. The ADC with an active die area of 0.17 $mm^2$ consumes 47.8 mW at 1.2 V and 1.2 GS/s.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.9
• /
• pp.2229-2236
• /
• 2014

In this paper, we proposed and implemented the automated cable-spreading program which can be done effectively cabling plan for electrical equipment in power plant. Cause the process of existing cable-spreading design was written in by hand, there are grossly inefficient gain by a personal and time investment with cable omission and unfixed overfill value. Proposed automation program for cable-spreading, which is coded cable and raceway, can calculate the overfill value and raceway change. Some experiments are conducted so as to verify the proposed model, and as a result, implemented cable-spreading program is well performed.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.37 no.8
• /
• pp.1029-1043
• /
• 2013

The pearl is a highly valuable gem that has historically represented wealth and power. Pearl necklaces have developed intro various types and represent an essential status item for modern women. This study first examines the symbolic and various meanings of pearls. Second, this study examines wearing types and pearl necklace patterns based on historical figures and modern fashion icons famous for personal displays of pearls. This study examines and analyzes various specialty publications about jewels, history of costumes, fashion magazines, academic research data, and internet search results. The conclusion of this study is as follows. Pearls have various symbolic meanings that are unlike other gems. Pearls represent purity, innocence, marital fidelity, an intimate relationship with the moon, frozen tears of God, solitude, triumph over adversity, wisdom, and sensual attraction. The societies and people traditionally famous for pearls were the Roman Empire, Queen Cleopatra of Egypt, Queen Theodora of the Byzantine Empire, Queen Elizabeth I, Queen Marie Antoinette, Empress of Eugenie Napoleon III, and Queen Alexandra. They showed a special affection for pearl necklaces and various wearing patterns unique to the time. Their pearl necklaces became a historic and symbolic legacy. Reestablished through the costume jewelry of cultivated pearls designed by Coco Chanel in the $20^{th}$ century, the pearl necklace has showed a variety of fashion trends in addition to a traditional symbolism of wealth and power. Josephine Baker, Louise Brooks, Marilyn Monroe, Elizabeth Taylor, Jacqueline Kennedy, Queen Elizabeth II, Princess Diana, Michelle Obama and Sarah Jessica Parker have worn notable pearl necklaces and established an individual style that utilizes the adornment of fashionable and stylish pearl necklaces. They have worn pearl necklaces while applying various fashion trend motifs to symbolic pearl features of that have changed the perception of the pearl and themselves.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.441-443
• /
• 2005

According as CCFL(Cold Cathode Fluorescent lamp) of light source in Backlight unit for Note PC (Personal computer) is presently needed to low power consumption and long life time, the development focus of CCFL is going on the discharge gas, phosphor and electrode material. First of all, discharge voltage characteristic of CCFL is closely connected with electrode material For low discharge voltage, the characteristic of electrode material is needed to low work function, low sputtering ratio and superior manufacturing property. We developed new CCFL with Nb/Ni Clad electrode superior to conventional CCFL. Because Nb/Ni Clad electrode with Ni material and Nb material, the electrical characteristic is superior to other electrode materials. The electrode of Nb/Ni Clad is composed that Ni of outside material has superior manufacturing property and Nb of inside material has low work function. Nb/Ni Clad of new electrode material is made by process of Rolling mill at high pressure and heat treatment. We compared electrical characteristic of Nb/Ni clad electrode with conventional Mo electrode by measurement. Mo electrode and Nb/Ni Clad electrode of cup type with diameter 1.1 mm and length 3.0mm are used to this experiment. Material content of Mo electrode is Mo 100%. But, Nb/Ni Clad electrode is composed by content of Nb 40% and Ni 60%. The result of comparison measurement between new CCFL with Nb/Ni Clad electrode and conventional CCFL was appeared that CCFL with Nb/Ni Clad electrode had superior characteristic than conventional CCFL. As a result of experiment, we completed Note PC with low power consumption and long life time by application of new CCFL with Nb/Ni Clad electrode.

• Journal of Power System Engineering
• /
• v.15 no.5
• /
• pp.10-15
• /
• 2011

This paper describes the engine performance and combustion characteristics of a CRDI diesel engine, operated by electronically controlled diesel fuel injector with variable injection timing. This experiment focused on fuel injection timing and pressure about combustion characteristics of CRDI diesel engine. EGR was excepted because it would be furtherly analyzed with additional experiments. The experiment was conducted under the circumstance of engine torque for 4, 8, 12 and 16 kgf-m and fuel injection timing for $15^{\circ}$, $10^{\circ}$ and $5^{\circ}$ BTDC, at the engine speed of 1100, 1400, 1700 and 2000 rpm. Fuel injection was controlled to retard or advance initiation of the injection event by electronically controlled fuel injection unit injector on the personal computer. When fuel was injected into the cylinders of a CRDI diesel engine it would go through ignition delay before starting of combustion. Therefore, fuel injection timing of CRDI diesel engine had a significant effect upon performance and combustion characteristics. Depending on the injection timing the fuel consumption rate following the rotational speed and torque was 3~78 g/psh (1.7~30.6%). The range of fuel injection timing that resulted in low fuel consumption overall was BTDC 15-10 degrees.