• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.11
• /
• pp.904-911
• /
• 2001

High-density lead zirconate titanate(Pb(Zr$\_$0.53/Ti$\_$0.47/)O$_3$, PZT) ceramics were fabricated by a new milling-precipitation(MP) process improved from the conventional solid state process. This process was progressed by a milling impregnation through mixing ZrO$_2$ and TiO$_2$ powders with lead nitrate(Pb(NO$_3$)$_2$) water solution in zirconia ball media, and then milling precipitation was induced from precipitation of PbC$_2$O$_4$ by adding ammonium of oxalate monohydrate((NH$_4$)$_2$C$_2$O$_4$$.$H$_2$O) as a precipitant. As a result of this process, single-phase perovskite structure was formed at the calcination temperature of 750$\^{C}$ for Pb(Zr$\_$0.53/Ti$\_$0.47/)O$_3$ powders. In addition, the highest density at the sintering temperature of 1100$\^{C}$ was obtained, because of the highly sinterable PZT Powders ground through the re-milling process. Piezoelectric and dielectric properties of sintered sample were improved by MP process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.136-139
• /
• 1999

The post-annealing treatments on RF (Radio Frequency) magnetron sputtered PZI(Pb$\_$1.05/(Zr$\_$0.52/, Ti$\_$0.48/)O$_3$thin films(4000${\AA}$) have been investigated. for a structure of PZT/Pt/Ti/SiO$_2$/Si Crystallization pproperties of PZT films were strongly dependent on RTA(Rapid Thermal Annealing) annealing temperature. We were able to obtain a perovskite structure of PZT at a low temperature of 600$^{\circ}C$. P-E curves of Pd/PZT/Pt capacitor annealed at 700$^{\circ}C$ demonstrate typical hysteresis loops. The measured values of P$\_$r/, E$\_$c/, by post annealed at 700$^{\circ}C$ were 12.1 ${\mu}$C/$\textrm{cm}^2$, 120KV/cm respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.885-888
• /
• 2000

The effects of deposition temperature and post annealing process of ferroelectric PbZr$\sub$0.52/Ti$\sub$0.48/O$_3$(PZT) thin films by pulsed laser deposition (PLD) were investigated. The PZT thin films were deposited at 400, 450, 500, and 550$^{\circ}C$, with/without post annealing at 650$^{\circ}C$ for 30 min. The PZT thin films deposited above 500$^{\circ}C$ without post annealing were crystallized into peroveskite phase, but the PZT thin films deposited below 450$^{\circ}C$ had pyrochlore phase. The PZT thin films deposited below 450$^{\circ}C$ with post annealing also crystallized into pure perovskite. Compared to the PZT thin films which were deposited at 450$^{\circ}C$ and post annealed, the films deposited at 550$^{\circ}C$ have a columnar microstructure and high remnant polarization 28 (${\mu}$C/cm$^2$). With in-situ annealing at oxygen ambient, the PZT thin films reduced oxygen vacancies and increased retained polarization.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.51-54
• /
• 2003

Tb-doped lead zirconate titanate($Pb_{1.1}(Zr_{0.6}Ti_{0.4})O_3$; PZT) thin films on $Pt(111)/Ti/SiO_2/Si(100)$ substrates prepared by a sol-gel method. Films have a Zr/Ti ratio of 60:40 and perovskite phase structure. The effect on the structural and electrical properties of films measured according to Tb content. Dielectric and ferroelectric properties of PZT thin films were altered significantly by Tb-doping. The PZT thin film with higher dielectric constant and improved leakage current characteristic was obtained by adding 0.3 mol% Tb. At 100 kHz, the dielectric constant and the dielectric loss of the 0.3 mol% Tb-doped PZT thin film were 1611 and 0.24, respectively The remanent polarization(2Pr) of the 0.3 mol% Tb-doped PZT thin film was $61.4\;{\mu}C/cm^2$ and the coercive field was 61.9 kV/cm. Tb-doped PZT thin films showed improved fatigue characteristics comparing to the undoped PZT thin film.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.365-366
• /
• 2005

PZT films are the most intensively investigated because PZT has advantages such as low processing temperature and large remnant values. In this paper, the microstructure and electric properties of $Pb(Zr_x,Ti_{(1-x)})O_3/BaTiO_3$ heterolayered thick films with Zr mole ranging from 30 to 70 % screen printed onto a alumina substrate were studied. $Pb(Zr_x,Ti_{(1-x)})O_3$ and $BaTiO_3$ powders were prepared by the sol-gel method. The $BaTiO_3$ powders were calcined at $700^{\circ}C$ for 2 hours. Structural properties of $Pb(Zr_x,Ti_{(1-x)})O_3/BaTiO_3$ multilayered thick films were investigated. As a result of the X-ray diffraction (XRD) analysis, $Pb(Zr_x,Ti_{(1-x)})O_3/BaTiO_3$ exhibited a perovskite polycrystalline phase without pyrochlore phase or any preferred orientation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.340-341
• /
• 2005

Three different composition 130um thickness PZT were fabricated by extrusion method and burned out at $550^{\circ}C$ and sintered at $1260^{\circ}C$/2.5hrs. Actuator was fabricated using glass and Si(100) wafer by MEMS process. From XRD data, in case of DECH, perovskite phase peak strength is higher than others. We were able to obtain the information of grain growth and porosity by SEM images. Also DECH PZT on glass membrane(100um thickness) have larger displacement than others.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.489-490
• /
• 2006

The Ce-doped YAG(Yttrium Aluminum Garnet, $Y_3Al_5O_{12}$) phosphor powders were synthesized by Sol-gel method. The luminescence, formation process and structure of phosphor powders were investigated by means of XRD, SEM and PL. The XRD patterns show that YAG phase can form through sintering at $1000^{\circ}C$ for 2h. This temperature is much lower than that required to synthesize YAG phase via the conventional solid state reaction method. There were no intermediate phases such as YAP(Yttrium Aluminum Perovskite, $YAlO_3$) and YAM(Yttrium Aluminum Monoclinic, $Y_4Al_2O_9$) observed in the sintering process. The powders absorbed excitation energy in the range 410~510nm. Also, the crystalline YAG:Ce showed broad emission peaks in the range 480~600nm and had maximum intensity at 528nm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.366-367
• /
• 2006

Different orientated SBN thin films were deposited by Ion Beam Sputtering, and electric properties were measured on each orientation. Ferroelectric $Sr_xBa_{1-x}Nb_2O_6$(SBN) has excellent electro-optic, photo-refractive, piezoelectric, pyroelectric properties. SBN thin film has been deposited by various method, of sol-gel, PLD, CVD, sputtering, etc.. To avoid lead pollution of Pb-system perovskite ferroelectric materials. SBN thin films were fabricated for pyroelectric IR sensor. Using the ceramic target of the same composition and Pt(100)/$TiO_2/SiO-2$/Si(100) substrate, crystallization and orientation behavior as well as electric properties of the films were examined. Seed layer and thin films thickness was controlled to observe the effect on preferred orientation. We measured I-V, C-V, P-E hysteresis to characterize electric-properties on each orientations.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.276-277
• /
• 2006

1mm-thick BLT ceramics were sintered in accordance with a bulk ceramic fabrication process. AII XRD peaks detected in the sintered ceramics were indexed as the Bi-layered perovskite structure without secondary phases. Density was increased with increasing the sintering temperature up to $1050^{\circ}C$ and the maximum value was about 98% of the theoretical density. The remanent polarization (2Pr) value of BLT ceramic sintered at $1050^{\circ}C$ was approximately $6.5\;{\mu}C/cm^2$ at the applied voltage of 4.5 kV. The calculated electromechanical coupling factor ($k_t$) of it was about 5% and the mechanical quality factor (Qm) was about 2200. From these results, a BLT ceramic target for pulsed laser deposition (PLD) system was successfully fabricated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.7
• /
• pp.521-524
• /
• 2010

Low loss perovskite niobates and tantalates have been placed on a short list of functional materials for future technologies. In this study, we fabricated Ag(Ta,Nb)$O_3$ thick films on the $Al_2O_3$ substrates by the screen printing method. The Ag(Ta,Nb)$O_3$ powders were fabricated by the mixed oxide method. The sintering temperature and time were $1150^{\circ}C$ and 2 hrs, respectively. The results of XRD analysis showed that the specimens employed in this study had the pesudo cubic structure. The dielectric permittivity and loss tangent of the films have been characterized from 1 kHz to 1 MHz. Also the dielectric permittivity and loss tangent were measured from 303 K to 393 K. The electrical properties of the film are also discussed.