• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.40 no.4
• /
• pp.96-104
• /
• 2017

A one-shot system (device) refers to a system that is stored for a long period of time and is then disposed of after a single mission because it is accompanied by a chemical reaction or physical destruction when it operates, such as shells, munitions in a defense weapon system and automobile airbags. Because these systems are primarily related with safety and life, it is required to maintain a high level of storage reliability. Storage reliability is the probability that the system will operate at a particular point in time after storage. Since the stored one-shot system can be confirmed only through inspection, periodic inspection and maintenance should be performed to maintain a high level of storage reliability. Since the one-shot system is characterized by a large loss in the event of a failure, it is necessary to determine an appropriate inspection period to maintain the storage reliability above the reliability goal. In this study, we propose an optimal inspection policy that minimizes the total cost while exceeding the reliability goal that the storage reliability is set in advance for the one-shot system in which periodic inspections are performed. We assume that the failure time is the Weibull distribution. And the cost model is presented considering the existing storage reliability model by Martinez and Kim et al. The cost components to be included in the cost model are the cost of inspection $c_1$, the cost of loss per unit time between failure and detection $c_2$, the cost of minimum repair of the detected breakdown of units $c_3$, and the overhaul cost $c_4$ of $R_s{\leq}R_g$. And in this paper, we will determine the optimal inspection policy to find the inspection period and number of tests that minimize the expected cost per unit time from the finite lifetime to the overhaul. Compare them through numerical examples.

• Journal of dental hygiene science
• /
• v.11 no.4
• /
• pp.325-332
• /
• 2011

To get the evidences for decreasing the discomfort, dissatisfaction, and for improving management of the implant prothesis through assessment implant patients' awareness and discomforts about care of the prostheses. The subjects were 300 implant patients who treated in the 20 dental clinics in Pusan, Ulsan and Daegu. The general characteristics, recognition, maintenance, discomfort and dissatisfaction, and oral hygiene status were collected. Level of the discomfort and dissatisfaction was measured by a 5 Likert scale, and analyzed by the equivalent of 100. The life-span of the implants was overestimated, however, periodic recall check and scaling were underwent. The level of discomfort and dissatisfaction was generally good, but many of them (65.3%) complained the food impaction. As a result of the multiple regression analysis, level of the discomfort and dissatisfaction increased in case of more number of the prosthesis ($\beta$=0.864), however decreased in case of more frequent teeth brushing ($\beta$=0.737), more frequent periodic check ($\beta$=-0.737), longer duration from the implantation ($\beta$=-0.090). It is very important for the implant patients to be recognized that the lack of care may shorten the life-span of the implant prosthesis. Therefore, efforts of the continuous oral hygiene care such as, periodic recall check, scaling, teeth brushing, the correct using of additional oral hygiene product, and education would be more emphasized.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.6
• /
• pp.589-597
• /
• 2010

Steel structures have a higher probability of being damaged by fatigue than by other causes of deterioration. As such, their maintenance to prevent fatigue damage is essential to sustain their safety and performance during their service period. In their maintenance, the current state of their fatigue cracks must be assessed to determine appropriate reinforcement methods and the suitable time intervals of periodic inspections when fatigue cracks are detected. Determining the crack growth rate is a successful method of predicting fractures, but it requires technical knowledge on fracture mechanics and experience in numerical methods and software for finite element analysis. In this study, a fatigue crack growth test on through-thickness cracked steel plates was conducted to assess the crack growth rate without superior technical knowledge and experience. The relationship between the Crack Opening Displacement (COD) and the crack growth rate was found in relatively long fatigue cracks.

• The Journal of Korean Academy of Prosthodontics
• /
• v.58 no.4
• /
• pp.385-391
• /
• 2020

Denture adhesive is a material used to improve the retention and stability of the denture. And denture adhesive is divided into soluble and insoluble type. It improves the retention, stability of dentures, and masticatory functions of patients. Maintenance like cleansing and periodic follow up is essential. Almost of dental clinicians are only simply aware of the effects of denture adhesives and often rely on the manufacturer's instructions on precautions and maintenance. The purpose of this study is to examine the properties, effects, and precautions of denture adhesives, and to present clinical guidelines for patients and professionals.

• The Journal of the Korean dental association
• /
• v.47 no.9
• /
• pp.585-595
• /
• 2009

Purpose : The aim of this study was to compare surgical complications between simple implant placement and implant placement combined with complicated surgical procedures. We also evaluated prosthetic complications according to the specific types of prosthesis. Material and Method : A retrospective analysis of dental chart of patients who was performed implant therapy during the period from June 2003 to December 2005 was carried out. This study was performed on 408 patients (208 male, 200 female). In addition, 1671 implants were performed. Based on their medical record and radiographs, the authors evaluated surgical and prosthetic complications, surgical procedures accompanied at the time of implant, risk factors of implant failure etc. Result : Surgical complications were developed on 358 implants(21.4% on total placed implants) and wound dehiscence was most prevalent complication. On maxillary posterior area, surgical complications developed more frequently on implants with major surgery and showed a significant difference. And complication rate of implants accompanied with GBR was higher than that of simple implants placement and also showed significant difference. The implant supported prosthesis showed no statistical difference in the occurrence of complications according to the types of prosthesis, and food retention was the most common post-prosthetic complication. Also we speculated that length and width of implant showed significant correlation to the failure of implant primary osseointegration. Conclusion : Based on the result, clinician should provide more careful maintenance for patients with implant placement accompanied by complicated surgical procedure. And periodic maintenance for the patient is requested for long-term survival of implant therapy.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.7
• /
• pp.679-683
• /
• 2016

Boilers of large-sized coal-fired power plants are being operated under very poor conditions such as continuous operation or repeating of start-up and shutdown for a stable supply of electricity. Thus periodic inspection and maintenance are required to ensure reliability of operation. The loads of existing scaffolding systems for the maintenance of boilers are concentrated in the lower parts structurally, which may cause a serial collapse of the overall scaffolding system when there are problems in some members. Therefore, in this study, a safe furnace scaffolding system is developed by dispersing the loads in the upper part, as well as minimizing the hazards of serial collapsing. In addition, for cases where the direct installation of furnace scaffolding is challenging owing to the structure of the boiler tube, a lifting system for the installation of furnace scaffolding is developed so that furnace scaffolding can be supported to secure the integrity of the power generating facility.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.1
• /
• pp.147-156
• /
• 2003

In this research, multiple corrosion factors of buried environments were measured in order to establish a formula for the corrosion character of corrugated steel structures in domestic environments. By substituting corrosion factors for each predicting formula, the durable lifetime was measured, and the measured lifetime was compared with the estimated lifetime by applying existing thickness-measuring techniques. A new usage standard was proposed with these results, in order to create the conclusion below. There are known differences in the soil factors used as variables in estimating the duration caused by the seasonal effects of rainfall and temperature. Comparing the durable lifetime estimated by each predicting formula, the findings show that the California technique is conservative. This study demonstrates that the error range of the AISI technique, which is mostly used as a duration technique, is a very narrow predicting technique as compared with many other countries. Considering that there is on average, a 13% error margin in this study, a proposed safety factor of 0.87 could be used to more accurately predict the duration. The laying time in the California technique is not longer than the whole durability, and as a result, this error margin exists. It is concluded that this study on the open area has been overdue. Based on these findings, it's proposed that this error margin should be applied to the domestic environment through periodic observation, in order to establish the predicting techniques of durable lifetime.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.05a
• /
• pp.178-180
• /
• 2016

TMDE(Test Measurement and Diagnostic Equipment) which is using in the military weapon system should perform the periodic calibration to maintain a measurement reliability during the life cycle, organizations are faced with increasing pressures to minimize costs while improving the reliability of test equipment. Previous studies suggest that reliability models are determined by considering simple size and characteristics of equipment, however an applying single Model may not be fit well maintenance data of many kinds of TMDEs. This paper presents that recommending an optimal calibration interval through the goodness of fit test with verifying statistical significance level among the several intervals which are computed with using major reliability models. According to the result of applying the actual proposed of calibration interval analysis method for various types of equipment, reliabilities are maintained for the end of calibration intervals.

• The KIPS Transactions:PartD
• /
• v.8D no.3
• /
• pp.221-232
• /
• 2001

Due to rapid advance of wireless communication technology, demand on data services in mobile environment is gradually increasing. Caching at a mobile client could reduce bandwidth consumption and query response time, and yet a mobile client must maintain cache consistency. It could be efficient for the server to broadcast a periodic cache invalidation report for cache consistency in a cell. In case that long period of disconnection prevents a mobile client from checking validity of its cache based solely on the invalidation report received, the mobile client could request the server to check cache validity. In doing so, some schemes may be more efficient than others depending on the number of available channels and the mobile clients involved. In this paper, we propose new cache consistency schemes, effects, efficient especially (1) when channel capacity is enough to deal with the mobile clients involved or (2) when that is not the case, and evaluate their performance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7893-7901
• /
• 2015

It is important to the periodic collection and analysis of the maintenance and management information of bridges for a more safe and efficient management of the bridges. To enhance the reliability and ease of acquisition of the bridge inspection information that is the basis for a strategy for safe and economic management using the bridge management system (BMS), this study develops a smart phone application for bridge inspection and ensures the actual applicability of the application. The developed application that is linked with the BMS for life-cycle management of bridges is possible to real-time query, modify and transmit of the maintenance-related information, and the application is able to greatly relieve the time and cost for the bridge inspection through the automatic creation of site inspection reports. The proposed method using the application is directly or indirectly expected to be very high effects of value improvement, such as ease of use, improved accuracy, sustainability of information, and future utilization, compared to conventional inspection method.