• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.85-93
• /
• 1991

Engine oil of the vehicle is very important to reduce friction and wear of the moving parts as long as possible without deterioration. As the technique of engine design and manufacturing improves, the performance of engine was increased greatly with the improvement of the quality of engine oil. All the additives and formulations skill of engine oil produced in our country are imported from foreign country. So it is necessary to study the basic knowledge of the mechanism of friction and wear of engine oil for the development of our own formula and additives. From this research, the basic mechanism of tribology and the change of oil properties were studied with a home made oil and two foreign oils by bench and engine test and laboratory works.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.26-36
• /
• 2010

This paper provides a description of the combustion model to obtain an accurate dynamic engine phenomena that satisfies real-time simulation for model-based engine control. The combustion chamber is modeled as a storage device for mass and energy. The combustion process is modeled in terms of a two-zone model for the burned and unburned gas fractions. The mass fraction burnt is modeled in terms of a Wiebe function. The instantaneous net engine torque is calculated from the engine speed and the instantaneous piston work. The modeling accuracy has been tested with a cylinder pressure data on a test bench and also the ability of real-time simulation has been checked. The results show that combustion model yields sufficiently good performance for the model-based control logic design. However the influence factors effected on model accuracy are some room for improvement.

• 한국연소학회:학술대회논문집
• /
• 2004.06a
• /
• pp.165-172
• /
• 2004

Co-incineration of coal and wastewater sludge was r;erfonn:rl in a O.lMWth bench scale circulating fluidized bed combustor(CFBC) Sludge was received from a wastewater treatment plant in a dye industrial complex in Busan. Metropolis. Moisture content of received sludge was 80%. Coal and sludge mixture was prepared with weight ratio of 90/10, 85/15 and 80/20. Co-combustion characteristics of the coal and sludge mixture demonstrated stable combustion conditions. Component analysis, incineration characteristics, boiler performance was measured before and after the test and application for commercial 59MWth CFBC boiler. The release of hazardous components such as $SO_2$ and Cl was suppressed by the presence of inherent minerals of Ca, Na, K in coal and sludge mixture. Pre-drying was not essential but it was recommended for the benefits of manageability of sludge.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.7-11
• /
• 2008

This paper describes design procedure and control strategy of HDC(High side DC/DC Converter) and MCU(Motor Control Unit) for diesel hybrid electric vehicle. In designing HDC and MCU for HEV high power density and reliability is strongly needed to meet the demand of automotive industry. In order to achieve the high performance of a controller, MPC5554 based control board is developed. An optimized film capacitor and inductor are also developed for high efficiency driving. Skim 63 IGBT module of SEMIKRON for automotive is used for power switching device. The most efficient cooling model for optimal size and reliability were verified by simulation. These procedures are verified by bench or driving test and the results are present in this paper.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.2
• /
• pp.475-483
• /
• 1993

A computer simulation model of a hermetic reciprocating type of refrigeration compressor has been developed. The compressor simulation model constitutes 6 control volumes, to each of which conservation laws of mass and energy are applied to yield full description of the refrigerant state along its passage. Instead of ideal gas assumption. real gas equation is employed. Some of valve-related input data required for the simulation are acquired from test bench experiments. The refrigerant states such as pressure and temperature, etc., mass flow rates, and valve motions can be predicted by the simulation. The calculated P-V diagram shows a good agreement with experimental result.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.6 no.4
• /
• pp.16-23
• /
• 2009

The major system of an agricultural shuttle power-shift tractor is the transmission, using power-shift. Because the shifting performance depends on the hydraulic control system, the most important aspect of the optimization is the design of the hydraulic control system. This study was conducted to develop the simulation model of hydraulic control system for the shuttle power-shift transmission by using Easy5 software. Bench test was conducted to verify the simulation. Also, the design parameters which influence the pressure modulation characteristics were investigated.

• Journal of Energy Engineering
• /
• v.23 no.2
• /
• pp.170-174
• /
• 2014

This paper presents the influences of ethanol addition to gasoline on bench test a spark ignition engine performances and emissions characteristics. The use of ethanol gasoline blended fuels decrease the brake power and brake torque, and increases the brake specific fuel consumption (BSFC). Ethanol gasoline blended fuels show lower brake torque and brake power and higher BSFC than gasoline. When ethanol containing oxygen is blended with gasoline, the combustion of the engine becomes better and therefore CO emission is reduced. HC emissions decrease to some extent as ethanol added to gasoline increase, as the percentage of ethanol in the blends increased, NOx emission was decreased under various engine speeds.

• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.49-57
• /
• 1991

Natural gas is one of the most promising alternative fuels for automative vehicles, because it has lower exhaust emissions and better fuel economy characteristics than gasoline and can be used in conventional engines with a little modification. In the present study, a conventional gasoline engine was modified to a CNG dedicated engine, which can be operated with CNG( compressed natural gas) only, and a engine bench test was performed at various compression ratios. As a result, it was revealed that the prototype CNG engine can be operated with lower exhaust emissions, better fuel economy and better thermal efficiency, but with a sightly reduced brake horse power, compared to the conventional gasoline engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.4
• /
• pp.196-203
• /
• 2003

This study was performed to design the optimal block type expansion valve through analyzing the characteristics of the block type expansion valve in automotive air conditioning system using HFC-134a. Because an alternative refrigerant (HFC-l34a) is being used instead of CFC-12 for automotive air conditioning system, newly designed air conditioning components are necessary due to changes in characteristics. The performance tests were accomplished through the test bench, that is manufactured based on the study. And then it was carried out to measure the variation of temperature and pressure at each part of the air conditioning system according to the compressor speed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.10
• /
• pp.833-839
• /
• 2013

Thermal vacuum test should be performed prior to launch to verify satellites' functionality in a harsh space environment which is represented by extremely cold temperatures and vacuum conditions. A thermal vacuum chamber which consists of a vacuum vessel, a pumping system, and a thermal control system are used to perform thermal vacuum tests of a satellite system and its components. A cryogenic blower is a core component of the closed loop thermal control system for thermal vacuum chambers. This paper describes the fan design of the cryogenic blower, the design of the thermal protection interface between the driving part and the fluid part, which were verified by thermal and structural analyses. The performance of the cryogenic blower is confirmed by similarity test on the test bench.