• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.5
• /
• pp.238-242
• /
• 2001

In this paper, we extracted design parameters for re-entrant mode microstrip directional coupler using FE(finite element) calculations. The microstrip directional coupler suffers from a poor directivity due to effect of the inhomogeneous dielectric including both dielectric substrate and air in microstrip transmission lines. Thus, the phase velocity of even mode is not equal to that of odd mode. In order to improve the directivity of microstrip directional coupler, a novel re-entrant mode microstrip directional coupler was employed. In microstrip configuration, the high directivity can be reached by matching the even- and odd-mode effective phase velocities. Through the values of capacitance obtained from 2-dimensional FE calculations, the phase velocities for each mode and the design parameter were extracted for the proposed parallel coupled-line configuration. Based on the extracted design parameter with phase matching condition, we designed and fabricated a 30dB directional coupler at 0.85GHz. Experimental results show good performance with excellent, isolation and directivity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.197-201
• /
• 2002

This paper presents optimized design, fabrication and thermal characteristics of micro-heaters for thermal MEMS (micro electro mechanical system) applications using SOI and trench structures. The micro-heaters are based on a thermal measurement principle and contains thermal isolation regions of 10 ${\mu}m$-thick Si membranes consisting of oxide-filled trenches in the SOI membrane rim. The micro-heaters were fabricated with Pt-RTD on the same substrate via MgO buff layer between Pt thin-film and $SiO_2$ layer. The thermal characteristics of micro-heater with trench-free SOI membrane structure was $280^{\circ}C$ at input power 0.9 W; in the presence of 10 trenches, it was $580^{\circ}C$ due to reduction of the external thermal loss. Therefore, a micro-heater with trenches in SOI membrane rim structure provides a powerful and versatile alternative technology for enhancing the performance of micro-thermal sensors and actuators.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.379-380
• /
• 2012

A bidirectional full-bridge CLLC resonant converter using a digital control method is proposed for a LVDC power distribution system. This converter can operate under high power conversion efficiency since the CLLC resonant network has soft switching capability for primary switches and output rectifiers. In addition, the power conversion efficiency of any directions is exactly the same as each other because of the symmetric structure of the converter. Intelligent digital control methods are proposed to regulate output voltage under any power flow directions. A 5kW prototype converter was designed for a high-frequency galvanic isolation of 380V dc buses using a digital signal processor to verify the performance of the proposed topology and algorithms.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.715-720
• /
• 2005

The rotating transmission is made up of belts, mass disks and gears. This precise piece of equipment is controlled electro-mechanically by the mote. and operation program. The control strategy and the transmission can be changed by belts' stiffness and change of the mass and gear. This transmission can be modeled as a rigid body, and also finds broad application in such diverse fields as machine tools, the cruise control system in automobiles, and control in the attitude and gimbals of spacecraft. The study of the rotating transmission excited by its base motion is not only able to predict the rotational performance, but obtain the fundamental data for vibration isolation. In this thesis, we studied the response abilities such as steady overshoot, undershoot and ect. and the response velocities such as rising time, settling time, and ect. in the rotating transmission through PD control experiment.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.7
• /
• pp.799-804
• /
• 2012

Recently micro-nano structures has widely been reported to improve the performance of waterproof, heat isolation, sound and light absorption in various fields of electric devices such as mobiles, battery, display and solar panels. A lot of micro-sized holes on the surface of thin film provide excellent sound, or heat, or light transmission efficiency more than solid film and simultaneously nano-sized protrusions around micro hole increase the hydrophobicity of the surface of thin film because of lotus leaf effects as generally known previously. In this paper new rapid fabrication process with 355 nm UV laser ablation was proposed to get micro-nano structures on the surface of thin film, which have only been observed at higher laser fluence. Developed thin micro-nano structured film was also investigated the hydrophobic property by measuring the contact angle and demonstrated the possibility to apply to water droplet separation.

• Journal of Mechanical Science and Technology
• /
• v.19 no.6
• /
• pp.1304-1312
• /
• 2005

The ride and noise characteristics of a vehicle are significantly affected by the vibration transferred to the body through the chassis mounting points in the engine and suspension. It is known that body attachment stiffness is an important factor of idle noise and road noise for NVH performance improvement. The body attachment stiffness serves as a route design aimed at isolating the vibration generated inside the car due to the exciting force of the engine or road. The test result of the body attachment stiffness is shown in the FRF curve data; the stiffness level and sensitive frequency band are recorded by the data distribution. The stiffness data is used for analyzing the parts that fail to meet the target stiffness at a pertinent frequency band. The analysis shows that the target frequency band is between 200 and 500 Hz. As a result of the comparison in a mounted suspension, the analysis data is comparable to the test data. From these results, there is a general agreement between the predicted and measured responses. This procedure makes it possible to find the weak points before a proto car is produced, and to suggest proper design guidelines in order to improve the stiffness of the body structure.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1144-1149
• /
• 2001

In this paper, a sliding mode controller of a fluid engine mount using MR (Magneto-Rheological) fluid was discussed When the MR fluid is applied to a fluid mount, resistance of MR fluid can be controlled by electro-magnetic valve installed in the inertia track. Since the rheological property of the MR fluid shows a function of shear rate, the damping characteristics of the mount will be change according to the frequency. Changing an applied magnetic field to the valve changes the property of the mount, such as the resistance of the MR fluid, the notch and the resonant frequencies due to the fluid passing, quantity of the fluid passing, the effective piston area of the volumetric damping and stiffness. Therefore, the fluid mount using MR fluid can be regarded as a variable structure system The sliding mode control known well as a particular type of variable structure control was introduced in this study. The sliding mode control, which has inherent robustness, is also expected to improve the control performance in the engine mount The sliding mode controller for the mount formatted by taking into account the response property with a time constant to MR fluid and the variable mount property. The motion equations of the fluid mount are derived from Newton's law of motion and used in numerical simulation. Numerical simulations illustrate the effectiveness of the sliding mode controller.

• Food Science and Biotechnology
• /
• v.17 no.6
• /
• pp.1246-1253
• /
• 2008

Phyllosticta melochiae, an endophytic fungus isolated from the healthy leaves of Melochia corchorifolia, was screened for the production of an anticancer drug, taxol on modified liquid medium and potato dextrose broth medium in culture for the first time. The presence of taxol was confirmed by spectroscopic and chromatographic methods of analysis. The amount of taxol produced by this fungus was quantified by high performance liquid chromatography. The maximum amount of fungal taxol production was recorded as $274{\mu}g/L$. The production rate was increased to $5.5{\times}1,000$ fold than that found in the culture broth of earlier reported fungus, Taxomyces andreanae. The fungal taxol extracted also showed a strong cytotoxic activity in the in vitro culture of tested human cancer cells by apoptotic assay. The results designate that the fungal endophyte, P. melochiae is an excellent candidate for an alternate source of taxol supply and can serve as a potential species for genetic engineering to enhance the production of taxol to a higher level.

• ETRI Journal
• /
• v.43 no.3
• /
• pp.414-426
• /
• 2021

In the task of data routing in Internet of Things enabled volatile underwater environments, providing better transmission and maximizing network communication performance are always challenging. Many network issues such as void holes and network isolation occur because of long routing distances between nodes. Void holes usually occur around the sink because nodes die early due to the high energy consumed to forward packets sent and received from other nodes. These void holes are a major challenge for I-UWSANs and cause high end-to-end delay, data packet loss, and energy consumption. They also affect the data delivery ratio. Hence, this paper presents an energy efficient watchman based flooding algorithm to address void holes. First, the proposed technique is formally verified by the Z-Eves toolbox to ensure its validity and correctness. Second, simulation is used to evaluate the energy consumption, packet loss, packet delivery ratio, and throughput of the network. The results are compared with well-known algorithms like energy-aware scalable reliable and void-hole mitigation routing and angle based flooding. The extensive results show that the proposed algorithm performs better than the benchmark techniques.

• Korean Journal of Pharmacognosy
• /
• v.50 no.3
• /
• pp.226-231
• /
• 2019

Prunus yedoensis Matsum. (Rosaceae) has been used for cough, urticaria, pruritus, dermatitis, asthma and relaxation in traditional Korean medicine. In this study, naringenin, sakuranetin and prunetin were isolated from the barks of P. yedoensis and quantification were performed by using high performance liquid chromatography (HPLC) method with diode array detector. The structures of naringenin and sakuranetin, prunetin were identified NMR spectroscopic data analysis. The content of each compound was analyzed by HPLC and the analytical method was validated through linearity, precision, accuracy and specificity test. The result showed that calibration curves of three compounds naringenin, sakuranetin and prunetin indicated great linearity with a correlation coefficient ($R^2$) of 1.00, 1.00 and 0.99. Intra and inter day measurement accuracy of the three compounds ranged from 92.70 ~ 112.70%, and showed precision was less than 3%. Therefore, the content analysis showed that naringenin ($0.132{\pm}0.016%$), sakuranetin ($0.108{\pm}0.023%$), and prunetin ($0.059{\pm}0.014%$).