• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.11
• /
• pp.1128-1134
• /
• 2014

In this paper, the effects of a metamaterial slab with negative permeability in a magnetically coupled wireless power transfer system (WPT) in the overall performance are analyzed quantitatively in terms of the effective quality factors of the loop resonators and coupling coefficient considering the slab losses, based on an equivalent circuit. Using the ideal metamaterial slab(lossless slab), the WPT efficiency is improved considerably by the magnetic flux focusing. However, the practical lossy slab made of RRs or SRRs limits the significant enhancement of WPT efficiency due to the relatively high losses in the slab consisting of RRs or SRRs near the resonant frequency. For the practical loop resonator, other than a point magnetic charge, using the practical lossy metamaterial slab in order to improve the transfer efficiency, the width of the slab needs to be optimized somewhat less than the half of the distance between two loop resonators. For the low-loss slab with its loss tangent of 0.001, the WPT efficiency is maximized at 93 % when the ratio of the slab width and the distance between the two resonators is approximately 0.35, compared with 53 % for the case without the slab. The efficiency in case of employing the high-low slab(loss tangent: 0.2) is maximized at 61 % when the slab ratio is 0.25.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.4
• /
• pp.317-325
• /
• 2020

UAV (Unmanned Aerial Vehicle) photogrammetry has recently emerged as a means of obtaining highly precise and rapid spatial information due to its cost-effectiveness and high efficiency. However, current procedures or regulations for quantitative quality verification methods and certification processes for UAV-images are insufficient. In addition, the current verification method for image quality is not evaluated by an MTF (Modulation Transfer Function) analysis or edge response analysis, which can analyze the degree of contrast including image resolution, and only relies on the GSD (Ground Sample Distance) analysis. Therefore, in this study, the edge response analysis using a Slanted edge target was performed along with GSD analysis to confirm the necessity of analyzing edge response analysis in UAV-images quality analysis. Furthermore, a Matlab GUI-based software tool was developed to help streamline the edge response analysis. As a result, we confirmed the need for edge response analysis since the outputs of the edge response analysis from the same GSD had significantly different outcomes. Additionally, we found that the quality of the edge response analysis of UAV-images is proportional to the performance of the camera mounted on the UAV.

• Journal of the Korean Magnetics Society
• /
• v.25 no.6
• /
• pp.189-197
• /
• 2015

As enforced the regulation of fuel efficiency, the electrification of automotive components in internal combustion vehicle has been applied instead of hydraulic pressure. A typical example of such parts is the EPS (electric power steering), and it is applied to most automotive at present. In electric power steering system, the core component is motor. The reduction of cogging torque and torque ripple is required to improve steering feeling and reduce NVH (Noise Vibration Harshness) in EPS. Generally the skewed design of stator or rotor is applied in order to reduce cogging torque and torque ripple. This paper propose the design and analysis methodology of Brusheless PMSM (Permanent Magnet Synchronous Motor) which is applied to skewed stator. The proposed methodology is as follows: First Intial Design PMSM with skewed stator for EPS, Second Optimal design using RSM (Response surface method), Third Performance Analysis such as Phase Back EMF, Inductance, Load torque using FEA (Finite Element Method). Finally, the reliability of proposed design methodology will be verified through the experiments of prototype sample.

• Journal of Convergence for Information Technology
• /
• v.10 no.11
• /
• pp.55-63
• /
• 2020

The IoT technology is a field that applies and converges the technologies in the existing industrial environment, instead of new technologies. The IoT technology is releasing various application services converged with other industries such as smart home, healthcare, construction, and automobile, and it is also possible to secure the work efficiency and convenience of users of IoT-based technologies. However, the security threats occurring in the IoT-based technology environment are succeeding to the vulnerability of the existing wireless network environment. And the occurrence of new and variant attacks in the combination with the ICT convergence environment, is causing damages. Thus, in the IoT technology-based environment, it would be necessary to have researches on the safe transmission of messages in the communication environment between user and device, and device and device. This thesis aims to design a safe communication protocol in the IoT-based technology environment. Regarding the suggested communication protocol, this thesis performed the safety analysis on the attack techniques occurring in the IoT technology-based environment. And through the performance evaluation of the existing PKI-based certificate issuance system and the suggested communication protocol, this thesis verified the high efficiency(about 23%) of communication procedure. Also, this thesis verified the reduced figure(about 65%) of the issued quantity of certificate compared to the existing issuance system and the certificate management technique.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.1
• /
• pp.1-11
• /
• 2005

Several Solid Freeform Fabrication Systems(SFFS) are commercialized in a few companies for rapid prototyping. However, they have many technical problems including the limitation of applicable materials. A new method of agile prototyping is required for the recent manufacturing environments of multi-item and small quantity production. The objectives of this paper include the development of a novel method of SFFS, the CAFL/sup VM/(Computer Aided Fabrication of Lamination for Various Material), and the manufacture of the various material samples for the certification of the proposed system and the creation of new application areas. For these objectives, the technologies for a highly accurate robot path control, the optimization of support structure, CAD modeling, adaptive slicing was implemented. However, there is an important problem with the conventional 2D lamination method. That is the inaccuracy of 3D model surface, which is caused by the stair-type surface generated in virtue of vertical 2D cutting. In this paper, We design the new control algorithm that guarantees the constant speed, precise positioning and tangential cutting on the 5DOF SFFS. We develop the tangential cutting algorithm to be controlled with constant speed and successfully implemented in the 5DOF CAFL/sup VM/ system developed in this paper. Finally, this paper confirms its high-performance through the experimental results from the application into CAFL/sup VM/ system.

• Journal of IKEEE
• /
• v.21 no.3
• /
• pp.268-271
• /
• 2017

In this paper, we propose the development of high resolution $360^{\circ}$ omnidirectional IP camera with 12 million pixels. The proposed 12-megapixel high-resolution $360^{\circ}$ omnidirectional IP camera consists of a lens unit with $360^{\circ}$ omnidirectional viewing angle and a 12-megapixel high-resolution IP camera unit. The lens section of $360^{\circ}$ omnidirectional viewing angle adopts the isochronous lens design method and the catadioptric facet production method to obtain the image without peripheral distortion which is inevitably generated in the fisheye lens. The 12 megapixel high-resolution IP camera unit consists of a CMOS sensor & ISP unit, a DSP unit, and an I / O unit, and converts the image input to the camera into a digital image to perform image distortion correction, image correction and image compression And then transmits it to the NVR (Network Video Recorder). In order to evaluate the performance of the proposed 12-megapixel high-resolution $360^{\circ}$ omnidirectional IP camera, 12.3 million pixel image efficiency, $360^{\circ}$ omnidirectional lens angle of view, and electromagnetic certification standard were measured.

• Journal of the Korean BIBLIA Society for library and Information Science
• /
• v.26 no.3
• /
• pp.101-128
• /
• 2015

The purpose of this study was to investigate the temporary librarians' employment status that have been placed in over 80% of the school libraries and deduce the issues of their job status for proposing some solutions to improve their job performance. To achieve the above research purposed in this study, the related literature was reviewed and analyzed and an interview was conducted with the librarians in the Chungbuk province and a survey was distributed in the same province. As a result, first, a high correlation was found between the total satisfaction and the factors as follows; 'working satisfaction', 'employment conditions', 'working environment', 'interpersonal relations' etc. In the difference verification based on the satisfaction in accordance with the employment status, a difference of satisfaction was found between the pre and post analyses of the unlimited contractions. Second, the most overall review of the temporary librarians' job performances in relation to the 'reading and lending performances was conducted, regardless of the librarian certification. Third, the temporary librarians working at the school libraries responded that 'the manpower developer' was the most difficult consideration in relation to their employment statuses. And, asked about the solutions for the improvement of their job conditions, most of the librarians wanted their job security.

• Journal of Korean society of Dental Hygiene
• /
• v.18 no.4
• /
• pp.477-488
• /
• 2018

Objectives: The purpose of this study was to investigate career competency, tasks, and job satisfaction of public servants, public institutions, and researchers. Methods: The survey was conducted about career competency, job satisfaction, and satisfaction on work life. Next, they interviewed on the characteristics of each job by two or three dimensions. The following conclusions were obtained from July to August 2017. Results: Career competencies were GPA with 3.87, 818 points of TOEIC score, and ITQ certification. Public servants required the information on literacy skills for employment and job performance, while civil servants need more than one year of clinical experience in the dental hospital. The non-commissioned officer needed a written test and fitness training. The health insurance review and assessment center required more than one year of experience from general hospital or medical institutions. Researchers required a research career, language skill, and professors required research and teaching experiences with clinical experience more than three years. The main job tasks were as follows; for public servants, they were official document processing and community projects. For the civilian workers and military/noncommissioned officers, they were medical assistant and administrative works. The employees of the health insurance review and assessment service are examining the medical expenses and the medical examination, the researchers are experimenting, researching and writing articles, and the teaching staff are lecturing and conducting individual research. Conclusions: The results of job satisfaction survey showed that occupational satisfaction was the highest in civil servants, researchers, and teaching professions. Job security was the highest in health workers and health inspectors' evaluation centers, and time vacancy was the highest in civilian workers and military/noncommissioned officers. If you want to work in such an institution, you should prepare elements that match your basic literacy and job specific characteristics. And we should try to increase the satisfaction of work even after work.

• The Journal of the Korea Contents Association
• /
• v.9 no.6
• /
• pp.289-299
• /
• 2009

This study set out to analyze the perceptions of investigative police officers and division police officers regarding Police Investigation Specialization, which had been in effect for four years, identify the problems, and search for alternative policies. The results led to the following alternative policies; first, the communication among the members should be facilitated by trading the jobs between investigative policemen and division members in certain percentage regularly, integrating job education and special work, and developing diverse support programs for detective activities to provide them with opportunities to experience and understand investigation. The second suggestion concerns the investigation members' morale. There should be a range of measures to boost their moral such as allocating separate budget and personnel to support the investigation department and the treatment of major criminal and civil cases, giving each investigation team an office and investigation room to improve their working environment, readjusting the promotion ratio of Police Investigation Specialization to introduce a promotion system proper for each investigation's characteristics. The third suggestion is to secure job efficiency. It's required to reinforce the current short-term specialized education program to bring up practical and professional investigators, open the certification exam of professional investigators to all members so that every policeman can have their abilities recognized and approved as long as they have the demanded capabilities, and create a system of shedding off the members idle at work by reflecting low performance records when evaluating the members to decide who to dismiss from Police Investigation Specialization. And finally, it's important to divide duties rationally. The rationality of duties division can be guaranteed by setting the guidelines for direct handling for the team leader to help him devote himself to his duties, defining objective criteria of measuring investigation workload, and creating devoted systems and teams for simple and small accidents so that experienced investigators can deal with high-profile cases.

• Journal of the Korean Data Analysis Society
• /
• v.20 no.6
• /
• pp.2993-3002
• /
• 2018

This case study introduces the process of developing the technology rating evaluation model for investment. The technology evaluation rating model for investment is a project that the Financial Services Commission and the Ministry of Commerce, Industry and Energy collaborated to expand the scope of technology finance from loan to investment. The technology evaluation model for investment was developed with the aim of predicting high growth companies. The model consists of a statistical model and an expert model. Here, statistical models were modeled by using logistic regression analysis. Expert models gathered opinions of experts and identified the weight of each evaluation item and set the model. The rating system of the model is composed of 10 grades. The distribution of the model was consistent with KTRS grade distribution. Interestingly, the emphasis is on technology and marketability. In the technology valuation grade model for the goddess, there is a considerable difference from the emphasis on managerial competence or business performance.